Galaxy Note 4 Unbrick/Debrick.img for N910G/F/T/W8 [unbrick] [unbrick image]

Was this helpful


  • Total voters
    95
Search This thread

yashthemw

Senior Member
Dec 11, 2015
818
471
Mumbai
First of all,

I would like to thank @Trex888 , for providing the debrick creator .

A special thanks to @dyasten for providing a working method of debricking n910f .

NOTE: DEBRICK IMAGES ARE AVAILABLE FOR N910G/F, IF YOU HAVE N910W8/T, SEE THE REFERENCE SECTION BELOW.
************************************************
Read this before proceeding any further.
>Please mention your model number while posting a query.
>Before trying any of these methods, load your note 4 in a bag and put it in the freezer (not kidding, i am serious).
>Keep it for a whole night, before removing it from freezer, these things should be ready:
Recovery firmware or stock rom loaded in odin, with every file in its respective slot, if you are using the recovery firmware, then uncheck auto reboot and tick f.reset time, repartition in odin's option tab.
My advice is, try to flash the stock rom first, if it doesnt works, then go for recovery firmware.

>Once you remove it from freezer, without any delay, connect it to pc and flash the firmware.


DEBRICKS:


This is the procedure:
-Open win32diskimager, load the debrick.img(3.74gb for n910f and 16mb for n910g).
-Flash it on a blank sd card, the card should be completely formatted and should be in fat32 format.
[/B ]-Once done, put that sd card in your bricked device.
-Connect it to your pc.
-Hold the power button for at least 10 sec or try the download mode key trio.
-It should vibrate.
-If it doesnt, hold it in front of an air conditioner,
let it cool( this has been tested).
-If it still doesnt vibrates, remove the battery, hold the power button for 10sec and then insert the battery.
-Now again try to press power button.
>So, once it vibrates, leave it for around 5min.
-Then press the volume down key+power+home.
-It should boot in to download mode.
-Now you can flash stock rom or recovery firmware.


RECOVERY FIRMWARES:

The correct way of flashing a recovery firmware:

- Load all the files in their respective slots ( ap, bl, cp, csc, pit ).
- select f.reset time, re-partition and uncheck auto reboot.
- Flash
- If it fails, then try without csc.
-Done
-Your phone will be back to normal.

Incase if any hardware buttons are not working, you can use this tool to get into download mode:
https://mega.nz/#!il9XXS6a!6yXq6uCBYpWzG0PLeAXhNpGqRZRmp4Oj3cRnTvNDPao
Turn your phone off, connect it to pc and put it in download mode via that software.

You dont even have to read any further unless you have a different variant of note 4.


If the device still acts weird, then refer this:
https://forum.xda-developers.com/showthread.php?p=70971598


Dont forget to press thanks.

****************************************************
REFERENCE:
If you are in a hurry to debrick your note 4 ,then go to these link, without reading any further, but don't forget to press thanks button :

■N910F:
http://forum.xda-developers.com/showthread.php?p=69489251
Or else:
People with bricked N910F can refer this page :
pastebin (dot) com/7KQxRRNF ,
just replace "(dot)" with " . "


■N910G users can try this :
http://forum.xda-developers.com/showthread.php?p=70006957

■N910W8:
https://mega.nz/#!TM8FUKrL!2tX2hrk3Oakxydw0GlkcXRkw7F3Oq6AHRlPPqGgtcPU ( by @Valentinez).

■For N910P refer this thread:
http://forum.xda-developers.com/showthread.php?t=3525923

■For n910t:
https://mega.nz/#!XRE1DbRL!uRcj8knB4QNV85QUDbXQe_9GLxrdcTYJC_DxNoyXkAA


Follow these steps for unbricking your device:
http://forum.xda-developers.com/showthread.php?p=69481229
************************************************


Here are qualcomm drivers , install them on pc :
https://mega.nz/#!4lNliRYJ!3blyZgKugEcdztDfyCjz_jrg_l4nO2UjUIckEFhMRks



************************************************
METHOD TO CREATE A DEBRICK VIA ODIN:
>PREREQUISITES:
-APQ 8084.pit file ( get it from here: https://mega.nz/#F!GscxXTgL!vBFl9ovSxsHM3xNo2jK40w)
-a Bootloader of your device(use the one from your recovery firmware)
-Any Samsung device having download mode.
-A SDHC CLASS 10 micro SD card(4gb, 16gb), it should blank and in FAT32 format.
- ODIN.
>PROCEDURE:
-Load the APQ 8084.pit file in the PIT section of ODIN.
-Load the Bootloader file in BL section of ODIN.
-In the options tab select: Auto Reboot, Re-Partition, F.Reset Time and T flash.
- Insert the blank sd card in a Samsung device and put the phone in Download mode.
-Connect the device to PC.
-Press START in ODIN.
That's it, you have your own debrick sd card, now you just have to insert it in your bricked device




************************************************

Reportedly , working on N910G and N910F.


Trex888 has already created a Debrick.img for n910t , hope all the other variants also get it.
Thanks to @Kurisoft , for sharing information about creating a debrick.img.


Don't forget to Press thanks .

Paypal ID: https://www.paypal.me/yashthemw
Reporting Via N910G
 
Last edited:

Trex888

Senior Member
Jul 26, 2016
1,490
1,126
40
Dubai
Check pm

First of all, I would like to thanks @Trex888 , for providing the debrick creator .

Note : If you want the debrick img , then you will have to make one for yourself.
I will be doing it for n910g , it will take some time, cause i will need a spare note 4 .
Anyways , if you want , create it and share .

Procedure :
So basically , you have to flash this zip file in recovery :
https://mega.nz/#!fJlWwawA!tsRI-0DMFyMcw8SVP1b7_nTyLK6xjiLzS6l1eZcJzxM

As stated by trex888 , this will create a file named Debrick.img in your internal storage .
Then you will have to put that debrick.img file on a sd-card(it should SDHC and I would advice a 32gb card ).

This can be done through PC , by using win32diskimager .
You can download win32diskimager from here :

http://forum.xda-developers.com/attachment.php?attachmentid=2598667&d=1393277797 )

Before putting this file on sd-card , make sure that it is formatted.
Once you got the file on your sd-card , just insert it into your costly paper weight (bricked note 4) .

Try to enter the download mode with the three key combination, if it doesnt enters the download mode, try all the possible key combinations .
Hope it helps .


Trex888 has already created a Debrick.img for n910t , hope all the other variants also get it.
Thanks to @Kurisoft , for sharing this information .

Reporting Via N910G

Check pm
 

rakieta

Senior Member
Oct 3, 2014
113
19
Question. When I create a Debrick.img I must first stock Fimware Flashen or does it go during Costom Rom?
 

yashthemw

Senior Member
Dec 11, 2015
818
471
Mumbai
Question. When I create a Debrick.img I must first stock Fimware Flashen or does it go during Costom Rom?
If you want to create a debrick.img , then you have to be on a stock rooted firmware .
But why are you making one more ,
I have already made one .
Try it and report here.

Sent from my SM-N910G using Tapatalk
 

rakieta

Senior Member
Oct 3, 2014
113
19
If you want to create a debrick.img , then you have to be on a stock rooted firmware .
But why are you making one more ,
I have already made one .
Try it and report here.

Sent from my SM-N910G using Tapatalk

Because my device is N910F and your image. Is N910G. Or does it not matter? I can not test it at the moment because my cell phone is not bricked, but be prepared is good;)
 

yashthemw

Senior Member
Dec 11, 2015
818
471
Mumbai
Because my device is N910F and your image. Is N910G. Or does it not matter? I can not test it at the moment because my cell phone is not bricked, but be prepared is good;)
No one has tested it yet on n910f , but if your n910f gets bricked (hope it doesnt) , then you can try your luck .

Reporting Via N910G
 

yashthemw

Senior Member
Dec 11, 2015
818
471
Mumbai
debrick.img for N910F not working. The phone does not even begin to read SDcard
Sad to know .
I hope , you followed the correct steps .
Anyways thanks for reporting .
If you know a functional n910f user , then ask him to create a debrick.img for F variant.
It wont brick his device .
I would have done it , but i have n910g .
The only requirement for creating debrick.img, is to be on a stock rooted firmware.

Reporting Via N910G
 

Top Liked Posts

  • There are no posts matching your filters.
  • 106
    First of all,

    I would like to thank @Trex888 , for providing the debrick creator .

    A special thanks to @dyasten for providing a working method of debricking n910f .

    NOTE: DEBRICK IMAGES ARE AVAILABLE FOR N910G/F, IF YOU HAVE N910W8/T, SEE THE REFERENCE SECTION BELOW.
    ************************************************
    Read this before proceeding any further.
    >Please mention your model number while posting a query.
    >Before trying any of these methods, load your note 4 in a bag and put it in the freezer (not kidding, i am serious).
    >Keep it for a whole night, before removing it from freezer, these things should be ready:
    Recovery firmware or stock rom loaded in odin, with every file in its respective slot, if you are using the recovery firmware, then uncheck auto reboot and tick f.reset time, repartition in odin's option tab.
    My advice is, try to flash the stock rom first, if it doesnt works, then go for recovery firmware.

    >Once you remove it from freezer, without any delay, connect it to pc and flash the firmware.


    DEBRICKS:


    This is the procedure:
    -Open win32diskimager, load the debrick.img(3.74gb for n910f and 16mb for n910g).
    -Flash it on a blank sd card, the card should be completely formatted and should be in fat32 format.
    [/B ]-Once done, put that sd card in your bricked device.
    -Connect it to your pc.
    -Hold the power button for at least 10 sec or try the download mode key trio.
    -It should vibrate.
    -If it doesnt, hold it in front of an air conditioner,
    let it cool( this has been tested).
    -If it still doesnt vibrates, remove the battery, hold the power button for 10sec and then insert the battery.
    -Now again try to press power button.
    >So, once it vibrates, leave it for around 5min.
    -Then press the volume down key+power+home.
    -It should boot in to download mode.
    -Now you can flash stock rom or recovery firmware.


    RECOVERY FIRMWARES:

    The correct way of flashing a recovery firmware:

    - Load all the files in their respective slots ( ap, bl, cp, csc, pit ).
    - select f.reset time, re-partition and uncheck auto reboot.
    - Flash
    - If it fails, then try without csc.
    -Done
    -Your phone will be back to normal.

    Incase if any hardware buttons are not working, you can use this tool to get into download mode:
    https://mega.nz/#!il9XXS6a!6yXq6uCBYpWzG0PLeAXhNpGqRZRmp4Oj3cRnTvNDPao
    Turn your phone off, connect it to pc and put it in download mode via that software.

    You dont even have to read any further unless you have a different variant of note 4.


    If the device still acts weird, then refer this:
    https://forum.xda-developers.com/showthread.php?p=70971598


    Dont forget to press thanks.

    ****************************************************
    REFERENCE:
    If you are in a hurry to debrick your note 4 ,then go to these link, without reading any further, but don't forget to press thanks button :

    ■N910F:
    http://forum.xda-developers.com/showthread.php?p=69489251
    Or else:
    People with bricked N910F can refer this page :
    pastebin (dot) com/7KQxRRNF ,
    just replace "(dot)" with " . "


    ■N910G users can try this :
    http://forum.xda-developers.com/showthread.php?p=70006957

    ■N910W8:
    https://mega.nz/#!TM8FUKrL!2tX2hrk3Oakxydw0GlkcXRkw7F3Oq6AHRlPPqGgtcPU ( by @Valentinez).

    ■For N910P refer this thread:
    http://forum.xda-developers.com/showthread.php?t=3525923

    ■For n910t:
    https://mega.nz/#!XRE1DbRL!uRcj8knB4QNV85QUDbXQe_9GLxrdcTYJC_DxNoyXkAA


    Follow these steps for unbricking your device:
    http://forum.xda-developers.com/showthread.php?p=69481229
    ************************************************


    Here are qualcomm drivers , install them on pc :
    https://mega.nz/#!4lNliRYJ!3blyZgKugEcdztDfyCjz_jrg_l4nO2UjUIckEFhMRks



    ************************************************
    METHOD TO CREATE A DEBRICK VIA ODIN:
    >PREREQUISITES:
    -APQ 8084.pit file ( get it from here: https://mega.nz/#F!GscxXTgL!vBFl9ovSxsHM3xNo2jK40w)
    -a Bootloader of your device(use the one from your recovery firmware)
    -Any Samsung device having download mode.
    -A SDHC CLASS 10 micro SD card(4gb, 16gb), it should blank and in FAT32 format.
    - ODIN.
    >PROCEDURE:
    -Load the APQ 8084.pit file in the PIT section of ODIN.
    -Load the Bootloader file in BL section of ODIN.
    -In the options tab select: Auto Reboot, Re-Partition, F.Reset Time and T flash.
    - Insert the blank sd card in a Samsung device and put the phone in Download mode.
    -Connect the device to PC.
    -Press START in ODIN.
    That's it, you have your own debrick sd card, now you just have to insert it in your bricked device




    ************************************************

    Reportedly , working on N910G and N910F.


    Trex888 has already created a Debrick.img for n910t , hope all the other variants also get it.
    Thanks to @Kurisoft , for sharing information about creating a debrick.img.


    Don't forget to Press thanks .

    Paypal ID: https://www.paypal.me/yashthemw
    Reporting Via N910G
    15
    Debrick.img for n910g and n910f created .
    I dont have a bricked note 4 , therefore someone with a bricked device will have to try.
    I have created it for g and f , with my functional note 4 , so please press thanks.

    Reporting Via N910G
    7
    Hi guys,
    I have created another debrick.img with my functianal note4, this time with the APQ RECOVERY PIT file via odin.
    I will be uploading it on mega.
    This is for n910g, there is nothing more I can do, this is like a last resort.
    Use win32diskimager to write this file on a blank sdcard, the card should be in fat32 format and should be SDHC.
    *Most of the People who have successfully debricked their n910g, have used a 32gb samsung evo card.

    Here is the debrick image for n910g:
    https://mega.nz/#!z4l3DAxT!5AiKk-itj3En2FGUcnqXA2sLI0O7nEupKyqk4bdofQ4

    Try and report here.


    If you are able to debrick your device, and think i deserve a thank, then dont hesitate to press the thanks button.[emoji13] [emoji13] [emoji13]
    Reporting Via N910G.
    6
    This is for N910F:

    For avoiding any more confusions , i have gathered all the links that are important .

    These are the only files that you will need to debrick a n910f ,download them all and you are good to go :

    This is the debrick.img :
    https://mega.nz/#!PpVXga4R!AAAAAAAAAABD2gFb4Kaw2QAAAAAAAAAAQ9oBW-CmsNk
    Google drive link for debrick:
    https://drive.google.com/open?id=0B3fU3AHc0FpCNWs0MHltUUR2dEE

    The next is win32diskimager :
    https://mega.nz/#!PtUDGArB!AAAAAAAAAAA60v-lpzEsZwAAAAAAAAAAOtL_pacxLGc

    Qualcomm drivers: https://mega.nz/#!4lNliRYJ!3blyZgKugEcdztDfyCjz_jrg_l4nO2UjUIckEFhMRks

    This is the recovery firmware for n910f (go to note4/511 and download each and every file ):
    https://mega.nz/#F!QIMmFRIT!Ns3AM-n0FUoMqOOWUif9ng
    ( thanks to @dyasten for this folder ) .

    You don't need anything else, just follow these steps:
    pastebin (dot) com/7KQxRRNF , just replace "(dot)" with " . "

    N910G USERS CAN ALSO TRY THESE STEPS , THE ONLY DIFFERENCE IS , TO FLASH THE CORRECT RECOVERY FIRMWARE , ONCE YOU GET INTO DOWNLOAD MODE :
    https://www.androidfilehost.com/?fid=24411628330025773


    HOPE THIS HELPS...

    Reporting via N910G.
    5
    Made a N910W8 Debrick.img!
    Made from Canadian N910W8 that I flashed with TWRP recovery, and was using Custom ROM, but Base firmware is COK3 5.1.1
    I have a Puerto Rico N910W8 that I Bricked HARD trying to flash Canadian Firmware [Marshmallow firmware to...]
    Computer Reads as Qualcomm QDLoader 9008
    Using steps in OP, created Debrick SD Card.
    I removed my Battery, insert debrick SD Card, put battery from NEW Note 4 into phone,
    [Somehow old battery went bad, maybe from bad flashing?]
    Volume Down+Home+Power...

    DOWNLOAD MODE, THANK GODS~!

    So I believe this Debrick.img will save all N910W8, from Canada or otherwise~!
    I just made a free Mega Account to upload the file, so bandwidth/number of uploads might be limited.

    N910W8 Debrick.img