[GUIDE] [FIX] YUREKA (AO5510) Touchscreen Calibration Issue

Search This thread

nitesh9

Senior Member
Sep 30, 2015
234
212
Siliguri
www.osbusters.com

Hurray! Finally, I fix the touch calibration issue; many many thanks to God who showed me the right path.

After suffering hard in last 15 days, even not getting any help from YU Officials, finally God bestowed upon me his blessings and provided me the hint to fix the issue.

What caused the Issue?

YU Televentures recently released a new batch of Yureka Plus (YU5510A-LP) devices with VoLTE feature. This created a storm in Yureka /Plus section of the forum. Some users even bricked after flashing the new firmware since it was totally different from the previous Yureka firmware. I got the backup of /system and /boot from a YU5510A-LP user. I deodexed the files and made a ROM out of it and flashed on my device to test whether it boots or not (a common process of ROM porting). It didn’t boot but it went beyond the boot logo and since the Kernel of YU5510-A didn’t have the correct display drivers for AO5510, I was getting strange characters on the screen. After that I rebooted to TWRP recovery. I was shocked the touch was malfunctioning. If I touch up it was working down, it was totally a mess. :mad:

This issue is much dangerous than bricking the device. Even if we brick, we may recover it by following @ricks guide, but with malfunctioning touchscreen phone is utterly useless. It can’t be fixed even after flashing the EMMC backup.

After that I reported to the YU Officials about the touch calibration issue, they didn’t provide any fix, but created a Warning thread regarding it. So sad. :(

They were even not ready to provide me the touch firmware of Yureka AO5510. They told me that they are also trying to find the cause of touch calibration issue and don’t have the required files. Here is the quote of the reply from YU Officials:

I am afraid that we don't have any files for fixing the issue. To make sure that such thing does not happen we internally test every case before releasing the software. In your case, you got the software from unknown sources and flashed it on your device with your own consent and understanding. Yes, we have devs but they work on cases which have higher reproducibility rate like the proximity sensor issue.

After that I analysed the YU5510A-LP VoLTE firmware and found that it was created by Coolpad, a Chinese Smartphone Company. So YU Televentures has imported not only the smartphone (YU5510A-LP) but also the firmware from Coolpad. That’s why it has some unknown bugs which the YU Offical Devs don’t know because they haven’t made the firmware. That’s why the devs didn’t have fix for touch calibration issue. YU is spending very less on service and devs, which very much disappointing. YU, an Indian brand made Yureka for tech freaks and that’s why so many devs engaged in it and even some noobish users like me became devs to raise the company above cheap Chinese brands. But now it’s status is deteriorating, it broke its partnership with Cyanogen and lost the support of so many great devs; and now it is left with some official noobish devs who are taking time like hell to provide a VoLTE patch for other users, this shows how irresponsible is the YU Company. And now it has already been provided by a YU Forum user. Even the Official YU OS is provided by our friend dev @AudioGod.

I hope my above words reaches to the YU Company and they take this criticizing in the right way and improve itself. I want to see this Indian Company rise beyond heights.

After lot of analysis and research I found that the cause of touch calibration issue was the kernel of YU5510A-LP ROM. It changed the TP-Firmware version and touch parameters of Yureka AO5510 (HD) according to Yureka YU5510A-LP (FHD) device and messed up the calibration.

This TP firmware is different in Yureka and Yureka Plus and it never changes after flashing any firmware (fastboot or ROM).

Yureka AO5510 : Each:GT970:0x1039:0x46
Yureka Plus YU5510 : Ofilm:GT970:0x1039:0x48
And mine was : Each:GT970:0x1039:0x47

Yureka (Plus) Touch Panel is manufactured by Goodix, a Chinese Touch Panel and Fingerprint Sensor company.


What didn’t fix the issue?
These are the things which didn't fix the calibration issue:
[/SIZE]
  • Flashing stock COS 12.1 ROM through recovery
  • Flashing COS 12.0/12.1 fastboot firmware
  • Flashing COS 12.0 CPB using YGDP tool (which threw an error of incompatible device before flashing)
  • Flashing all other partitons (=EMMC backup)
  • Using Annabathina’s Yureka Unbricking Tool

How did I find a Fix?
While surfing through internet I found a way to check the touch firmware version. Then I checked mine and also asked about it from other Yureka users. Then I searched about the firmware version and got an XDA Thread and also got to know about Goodix Touch Firmware and Goodix Firmware Upgrade Tool (GTP ADB Tool) from Elephone (another Chinese company) forum which I didn’t get from YU.

I read the XDA thread learned about the whole thing and created a Goodix TP Firmware/Config myself.


How to Fix Yureka AO5510 Touch Calibration Issue?

STEP 1: Download GtpAdbToolV1.7_20140424.zip and GT970_1039_AO5510-TP-Firmware.zip on your Windows PC and extract it. Go to the extracted folder of Gtp Adb Tool and run the GtpAdbTool.exe application. Then connect you YUREKA AO5510 to your PC (be sure USB debugging is enabled in your device). You will see the GTP ADB Tool window similar to the screenshot below:



STEP 2: Now click on the button as indicated in the screenshot below and navigate for the GT970_1039_AO5510-TP-Firmware.cfg file (that you extracted in Step 1) and select it.



STEP 3: Then click on the button indicated in the screenshot below to execute firmware upgrade process. Once completed, you can unplug your device and reboot. Voila touchscreen issue fixed! :)



NOTE (Important):

If the GTP ADB Tool doesn't detect your device or TP firmware, then flash any of the following ROMs:

NucleaROM by @Rakesh Batra
Hexagon ROM by @Rakesh Batra
Or any other ROM

If the above ROMs doesn’t work then try flashing
CoolUI 6.0 for YUREKA (Test build): https://www.androidfilehost.com/?fid=457095661767103935
(After flashing this ROM you may see a 'root' indication on YU LOGO, but you can fix that using Annabathina's Tool)


Important Files

GTP ADB Tool: https://www.androidfilehost.com/?fid=385035244224387037

YUREKA AO5510 TP Firmware: https://www.androidfilehost.com/?fid=385035244224387256


Credits

Special thanks to @iamreal2 (XDA member) and @Ethan (Elephone forum member)
Special thanks to @darshan1205, @ricks and @Men_in_black007 who supported me in bad times
Special thanks to @manis99 for providing me YU5510A-LP VoLTE Firmware :D
Special thanks to @prasoon Mehra for providing me original Yureka AO5510 TP Config.
And finally thanks to me for making this fix. :)
 

Attachments

  • GtpAdbToolV1.7_20140424.zip
    11.9 MB · Views: 743
  • GT970_1039_AO5510-TP-Firmware.zip
    405 bytes · Views: 632
Last edited:

nitesh9

Senior Member
Sep 30, 2015
234
212
Siliguri
www.osbusters.com
Last edited:

shailesh1985

Member
Feb 15, 2013
7
1
Hello nitesh9,

I am also having the same issue and tried above steps.
My phone is not getting detected. in the GTP tool. My Phone is rooted and running STOCK ROM..
it is getting connected in stock rom and GTP tool recognize it in ADB mode but not detecting TP chipset and IC version.

as you instructed , I downloaded nuclearom and tried to install it via CWM_recovery but installation is getting aborted showing error "System7".

ANY OTHER IDEA TO GET THIS DETECTED. PLZ HELP.. ALSO , I REALLY APPRECIATE YOUR EFFORT SHARING THIS KNOWLEDGEBASE.
 

shailesh1985

Member
Feb 15, 2013
7
1
Hello nitesh9,

I am also having the same issue and tried above steps.
My phone is not getting detected. in the GTP tool. My Phone is rooted and running STOCK ROM..
it is getting connected in stock rom and GTP tool recognize it in ADB mode but not detecting TP chipset and IC version.

as you instructed , I downloaded nuclearom and tried to install it via CWM_recovery but installation is getting aborted showing error "System7".

ANY OTHER IDEA TO GET THIS DETECTED. PLZ HELP.. ALSO , I REALLY APPRECIATE YOUR EFFORT SHARING THIS KNOWLEDGEBASE.

Many Thanks to all of you guys.... who have put their efforts a lot.
finally I succeed to repair touch for Yureka. but in little bit different way.

GTP tool was not working in both the custom ROM mentioned above. hence I started in recovery mode and mounted everything, immediately it detected the TP IC and its version and then I flashed the config. and... its done.
 
  • Like
Reactions: Saltmango

nitesh9

Senior Member
Sep 30, 2015
234
212
Siliguri
www.osbusters.com
Many Thanks to all of you guys.... who have put their efforts a lot.
finally I succeed to repair touch for Yureka. but in little bit different way.

GTP tool was not working in both the custom ROM mentioned above. hence I started in recovery mode and mounted everything, immediately it detected the TP IC and its version and then I flashed the config. and... its done.
I am glad that it worked for you...
BTW you better use TWRP Recovery to flash newer ROMs. CWM Recovery is very old and is abandoned and deprecated.
 

dhrtlockeroo9

Senior Member
Sep 24, 2013
251
50
Ahmedabad
Hello Sir, does it works with Yureka plus device also? My devices half touch only works after updating to lollipop. Please help me. I can't use my device. Thanks in Advance, please reply as soon as possible.
 

dhrtlockeroo9

Senior Member
Sep 24, 2013
251
50
Ahmedabad
nitesh9

Added Yureka Plus TP firmware to the second post...Use that. ;)

Sent from my YUREKA using Tapatalk

Can I flash this file via fastboot I can't use my device to enable USB debugging mode because of touch malfunctioning. Please suggest me any other way to flash file sir & Thanks a lot for helping me Sir.
 

nitesh9

Senior Member
Sep 30, 2015
234
212
Siliguri
www.osbusters.com
Can I flash this file via fastboot I can't use my device to enable USB debugging mode because of touch malfunctioning. Please suggest me any other way to flash file sir & Thanks a lot for helping me Sir.
Are you able to go into TWRP recovery?
If yes then mount all the partitions and then try the method.


You can also use mouse on OTG to use the phone.

Sent from my YUREKA using Tapatalk
 

dhrtlockeroo9

Senior Member
Sep 24, 2013
251
50
Ahmedabad
Sorry Sir, every time when while I tried to install TWRP is stuck always & once I succeeded but Touch not works for me I don't know why? Downloaded my own device 5510A TWRP but than also it's not responding like that. Can you tell me whole process to flash TWRP with TWRP IMG file for my Yureka plus device?
 

nitesh9

Senior Member
Sep 30, 2015
234
212
Siliguri
www.osbusters.com
Sorry Sir, every time when while I tried to install TWRP is stuck always & once I succeeded but Touch not works for me I don't know why? Downloaded my own device 5510A TWRP but than also it's not responding like that. Can you tell me whole process to flash TWRP with TWRP IMG file for my Yureka plus device?
Flash twrp through fastboot. Or use Yuware: https://drive.google.com/file/d/0B4X6UMHVd-NKTDQxdTBqaHlLb2M/view?usp=sharing

Sent from my YUREKA using Tapatalk
 

dhrtlockeroo9

Senior Member
Sep 24, 2013
251
50
Ahmedabad

nitesh9

Senior Member
Sep 30, 2015
234
212
Siliguri
www.osbusters.com
iS it possible if I flashed wrong firmware than also touch malfunctioning? But I flashed CM 12.1 official ROM.
What is your device...Wrong may cause the issue... Fastboot error also may cause the issue. It can also be a hardware issue...

If the given method doesn't help then it must be a hardware issue. You must contact YU Service / Care.

Sent from my YU5510A using Tapatalk
 

dhrtlockeroo9

Senior Member
Sep 24, 2013
251
50
Ahmedabad
What is your device...Wrong may cause the issue... Fastboot error also may cause the issue. It can also be a hardware issue...

If the given method doesn't help then it must be a hardware issue. You must contact YU Service / Care.

Sent from my YU5510A using Tapatalk

I Have Yureka plus 5510A device. I don't know what happed my device again hard bricked. I don't know how to recover back. I tried QFil fastboot recovery but always getting error Sahara download failed.
 

Top Liked Posts

  • There are no posts matching your filters.
  • 6

    Hurray! Finally, I fix the touch calibration issue; many many thanks to God who showed me the right path.

    After suffering hard in last 15 days, even not getting any help from YU Officials, finally God bestowed upon me his blessings and provided me the hint to fix the issue.

    What caused the Issue?

    YU Televentures recently released a new batch of Yureka Plus (YU5510A-LP) devices with VoLTE feature. This created a storm in Yureka /Plus section of the forum. Some users even bricked after flashing the new firmware since it was totally different from the previous Yureka firmware. I got the backup of /system and /boot from a YU5510A-LP user. I deodexed the files and made a ROM out of it and flashed on my device to test whether it boots or not (a common process of ROM porting). It didn’t boot but it went beyond the boot logo and since the Kernel of YU5510-A didn’t have the correct display drivers for AO5510, I was getting strange characters on the screen. After that I rebooted to TWRP recovery. I was shocked the touch was malfunctioning. If I touch up it was working down, it was totally a mess. :mad:

    This issue is much dangerous than bricking the device. Even if we brick, we may recover it by following @ricks guide, but with malfunctioning touchscreen phone is utterly useless. It can’t be fixed even after flashing the EMMC backup.

    After that I reported to the YU Officials about the touch calibration issue, they didn’t provide any fix, but created a Warning thread regarding it. So sad. :(

    They were even not ready to provide me the touch firmware of Yureka AO5510. They told me that they are also trying to find the cause of touch calibration issue and don’t have the required files. Here is the quote of the reply from YU Officials:

    I am afraid that we don't have any files for fixing the issue. To make sure that such thing does not happen we internally test every case before releasing the software. In your case, you got the software from unknown sources and flashed it on your device with your own consent and understanding. Yes, we have devs but they work on cases which have higher reproducibility rate like the proximity sensor issue.

    After that I analysed the YU5510A-LP VoLTE firmware and found that it was created by Coolpad, a Chinese Smartphone Company. So YU Televentures has imported not only the smartphone (YU5510A-LP) but also the firmware from Coolpad. That’s why it has some unknown bugs which the YU Offical Devs don’t know because they haven’t made the firmware. That’s why the devs didn’t have fix for touch calibration issue. YU is spending very less on service and devs, which very much disappointing. YU, an Indian brand made Yureka for tech freaks and that’s why so many devs engaged in it and even some noobish users like me became devs to raise the company above cheap Chinese brands. But now it’s status is deteriorating, it broke its partnership with Cyanogen and lost the support of so many great devs; and now it is left with some official noobish devs who are taking time like hell to provide a VoLTE patch for other users, this shows how irresponsible is the YU Company. And now it has already been provided by a YU Forum user. Even the Official YU OS is provided by our friend dev @AudioGod.

    I hope my above words reaches to the YU Company and they take this criticizing in the right way and improve itself. I want to see this Indian Company rise beyond heights.

    After lot of analysis and research I found that the cause of touch calibration issue was the kernel of YU5510A-LP ROM. It changed the TP-Firmware version and touch parameters of Yureka AO5510 (HD) according to Yureka YU5510A-LP (FHD) device and messed up the calibration.

    This TP firmware is different in Yureka and Yureka Plus and it never changes after flashing any firmware (fastboot or ROM).

    Yureka AO5510 : Each:GT970:0x1039:0x46
    Yureka Plus YU5510 : Ofilm:GT970:0x1039:0x48
    And mine was : Each:GT970:0x1039:0x47

    Yureka (Plus) Touch Panel is manufactured by Goodix, a Chinese Touch Panel and Fingerprint Sensor company.


    What didn’t fix the issue?
    These are the things which didn't fix the calibration issue:
    [/SIZE]
    • Flashing stock COS 12.1 ROM through recovery
    • Flashing COS 12.0/12.1 fastboot firmware
    • Flashing COS 12.0 CPB using YGDP tool (which threw an error of incompatible device before flashing)
    • Flashing all other partitons (=EMMC backup)
    • Using Annabathina’s Yureka Unbricking Tool

    How did I find a Fix?
    While surfing through internet I found a way to check the touch firmware version. Then I checked mine and also asked about it from other Yureka users. Then I searched about the firmware version and got an XDA Thread and also got to know about Goodix Touch Firmware and Goodix Firmware Upgrade Tool (GTP ADB Tool) from Elephone (another Chinese company) forum which I didn’t get from YU.

    I read the XDA thread learned about the whole thing and created a Goodix TP Firmware/Config myself.


    How to Fix Yureka AO5510 Touch Calibration Issue?

    STEP 1: Download GtpAdbToolV1.7_20140424.zip and GT970_1039_AO5510-TP-Firmware.zip on your Windows PC and extract it. Go to the extracted folder of Gtp Adb Tool and run the GtpAdbTool.exe application. Then connect you YUREKA AO5510 to your PC (be sure USB debugging is enabled in your device). You will see the GTP ADB Tool window similar to the screenshot below:



    STEP 2: Now click on the button as indicated in the screenshot below and navigate for the GT970_1039_AO5510-TP-Firmware.cfg file (that you extracted in Step 1) and select it.



    STEP 3: Then click on the button indicated in the screenshot below to execute firmware upgrade process. Once completed, you can unplug your device and reboot. Voila touchscreen issue fixed! :)



    NOTE (Important):

    If the GTP ADB Tool doesn't detect your device or TP firmware, then flash any of the following ROMs:

    NucleaROM by @Rakesh Batra
    Hexagon ROM by @Rakesh Batra
    Or any other ROM

    If the above ROMs doesn’t work then try flashing
    CoolUI 6.0 for YUREKA (Test build): https://www.androidfilehost.com/?fid=457095661767103935
    (After flashing this ROM you may see a 'root' indication on YU LOGO, but you can fix that using Annabathina's Tool)


    Important Files

    GTP ADB Tool: https://www.androidfilehost.com/?fid=385035244224387037

    YUREKA AO5510 TP Firmware: https://www.androidfilehost.com/?fid=385035244224387256


    Credits

    Special thanks to @iamreal2 (XDA member) and @Ethan (Elephone forum member)
    Special thanks to @darshan1205, @ricks and @Men_in_black007 who supported me in bad times
    Special thanks to @manis99 for providing me YU5510A-LP VoLTE Firmware :D
    Special thanks to @prasoon Mehra for providing me original Yureka AO5510 TP Config.
    And finally thanks to me for making this fix. :)
    2
    Original TP Firmware Files for Different Devices

    These are Original Stock Touch Panel Firmware/Configs for users who are suffering calibration issue not due to VoLTE firmware but due to other unknown causes.

    YUREKA (AO5510) : https://www.androidfilehost.com/?fid=457095661767104421 (Thanks to @Prasoon Mehra)
    YUREKA PLUS (YU5510) : https://www.androidfilehost.com/?fid=385035244224388338 (Thanks to @darshan1205)

    Users of other YU Devices may share their working TP Firmware to help others.... :)
    1
    Hello nitesh9,

    I am also having the same issue and tried above steps.
    My phone is not getting detected. in the GTP tool. My Phone is rooted and running STOCK ROM..
    it is getting connected in stock rom and GTP tool recognize it in ADB mode but not detecting TP chipset and IC version.

    as you instructed , I downloaded nuclearom and tried to install it via CWM_recovery but installation is getting aborted showing error "System7".

    ANY OTHER IDEA TO GET THIS DETECTED. PLZ HELP.. ALSO , I REALLY APPRECIATE YOUR EFFORT SHARING THIS KNOWLEDGEBASE.

    Many Thanks to all of you guys.... who have put their efforts a lot.
    finally I succeed to repair touch for Yureka. but in little bit different way.

    GTP tool was not working in both the custom ROM mentioned above. hence I started in recovery mode and mounted everything, immediately it detected the TP IC and its version and then I flashed the config. and... its done.
    1
    Hello Sir, does it works with Yureka plus device also? My devices half touch only works after updating to lollipop. Please help me. I can't use my device. Thanks in Advance, please reply as soon as possible.
    Added Yureka Plus TP firmware to the second post...Use that. ;)

    Sent from my YUREKA using Tapatalk