tinyurl.com/ycy3fhts in this post you have provided the Mega.nz link for patched boot image of firmware version A05 to A24 but my mobile have firmware version of A26 (Build Version: RMX3085_11_A.26). I completed step-1 and step-2 mentioned by you but can't proceed to step-3 because there is no firmware patch of A26 in mega.nz link that was provided by you. Can you please provide me link for A26 so I can proceed with step-3..
How To Guide [GUIDE][REALME 8][Unofficial] New method Unlock Bootloader, Flash TWRP and Root [RMX3085]
- Thread starter Tony Stark
- Start date
I have downloaded it. But there is no firmware version of A26. In addition, I would like to draw your attention towards that, the latest path provided by you in that zip file is of date 26 January 2022. And the firmware version A26 is released on February 2022. So basically all your patches might not be supported for it.
Hi my friends . I have a problem and I ask you to help me. I successfully unlocked my bootloader, but during the rooting process, my device did not turn on and gives the following error :
'The current image(boot/recovery) have been destroyed and can not boot.'
It should be noted that when I entered the following command in cmd in the third step (rooting your device), my device became like this :
'python mtk w boot,vbmeta boot.patched,vbmeta.img.empty'
Please help me. I have been involved in this problem for 30 days, but I have not reached a conclusion.
my device : Realme 8 ( RMX3085 )
'The current image(boot/recovery) have been destroyed and can not boot.'
It should be noted that when I entered the following command in cmd in the third step (rooting your device), my device became like this :
'python mtk w boot,vbmeta boot.patched,vbmeta.img.empty'
Please help me. I have been involved in this problem for 30 days, but I have not reached a conclusion.
my device : Realme 8 ( RMX3085 )
you did not flashed A.19 preloader, lk1 and lk2
flash them and then unlock bootloader again
for android 12, you better see and translate Russian posts from 4pda
A quick update on RUI3 rooting
Flashed Thailand firmware, applied for deep testing, unlocked bootloader and went back to my original firmware. Then I rooted using magisk.
Flashed Thailand firmware, applied for deep testing, unlocked bootloader and went back to my original firmware. Then I rooted using magisk.
Attachments
bro i also did all process of thai firmware but my device is not connecting on fastboot mode. Which platform tools and drivers you used?
Hello. Does flashing an unofficial ROM solve the problem? No matter how hard I tried, I could not solve this problem. If the problem is solved with an unofficial flash ROM, please introduce a valid free site to download the flash file as well as a way to flash your favorite ROMs for realme 8.
Most of them would have got their boot loaders unlocked officially by now. But couldn't find a step by step instructions anywhere to root the device in Android 12 running RUI3.0.
After trying over 10 times in different firmware A26.C05,C07 back to A22 as this is the only Rom where it doesn't say Dm-verity error & freezes up after 5-7 reboots
After trying over 10 times in different firmware A26.C05,C07 back to A22 as this is the only Rom where it doesn't say Dm-verity error & freezes up after 5-7 reboots
Similar threads
Top Liked Posts
-
There are no posts matching your filters.
-
7Hello guys!
As you all know that there is no deeptest.apk available for our device.
So we have to unlock our bootloader unofficially!
NOTE: IF U HAVEN'T UPGRADED AFTER A19 ROM THEN SKIP FIRST PART !!! And follow the instructions from 2nd part.
Also this method only works on RUI 2.0
DON'T TRY THIS IN RUI 3.0
So Lets Begin the Process:
1. Flashing A19 Partitions:
Requirements:
- PC or Laptop
- Internet connection
- Realme 8
- USB cable
- Take a backup of your data, Just in case if any error happens.
Requirements:
Bypass Tools Pack - (DRIVER AND BYPASS FILES)
SP Flash Tool
Decrypted OFP (OPPO FIRMWARE PACKAGE) Partitions:
Partitions.zip
Install Python from Windows Store
libusb-win32 - Having Issues? Use this.
Get usbdk installer (.msi) from here and install it
Steps:
1) Extract the zip
2) Go to driver folder, find the .inf file right click and press install.
3)Download this file and install it, after installing power off phone and connect to pc while holding Vol+- (don't leave the buttons after connecting) . You might need this driver as well if it's not detected.
Press next, connect your device to PC while holding Vol+- buttons (your device needs to be powered off, and don't leave the buttons) and you will see the mtkdriver down below. Install it.
Choose MediaTek USB Port and install it.
4)Then run the brom.bat under Bypass folder.
5) Now power off the phone and connect the phone while holding volume + and - (Don't leave the buttons until the bypass is done)
6)After the above step Go into Flash Tool folder and open the SPFlash tool and launch flash_tool.exe
7) Click on Options>Options and go to Connections and select UART and set Baud Rate to 921600
8)Now in Sp flash tool select the scatter file which you have extracted from Partitions.zip and make sure that prealoder, lk, and lk2 is selected.
9) You don't need to select auth file as authorization is disabled. Once you do it, it should look like this. ALWAYS MAKE SURE DOWNLOAD ONLY MODE IS SELECTED! DON'T SELECT OTHER MODES!
Make SURE "Download Only" is selected. Don't select ANYTHING ELSE! You will lose your IMEIs, Serial Numbers, Capability of Hardware Attestation etc. if you choose "Format data + Download" make SURE you selected "Download Only".
10) Now, you can start downloading with the button and after that a checkmark will appear. You can reboot your phone
After flashing it should look like this. Download has been complete.
2. UNLOCKING BOOTLOADER:
Requirements
- PC or Laptop
- Internet connection
- USB cable
- Take a backup of your data since it'll be wiped
- Go to About phone > Version and tap build number 7 times
- Go to Settings > advanced settings > Developer options and turn on OEM unlocking and USB debugging
- Install USBDk
- Download this and extract : https://github.com/bkerler/mtkclient/archive/refs/heads/main.zip
- Now open command prompt in that folder
- Now type
pip3 install -r requirements.txtand hit enter - Now type
python mtk e metadata,userdata,md_udchit enter - This command wipes data - Then power off your phone and hold both volume buttons and connect usb cable (DON'T LEAVE THE BUTTONS, KEEP THEM HOLDING THROUGHOUT THE PROCESS) - This boots device into BROM mode
- Now type
python mtk da seccfg unlockThis will unlock the bootloader (If you face waiting for device issue then unplug the device and plug in the device again with holding volume buttons, also don't leave the buttons) -
- After this unplug your phone and turn it on (It'll show your device dm verity corrupted and first boot might take 5-10 mins, don't panic)
- Now your bootloader is unlocked
- Due to realme's limitations you still can't access fastboot after unlocking via this method
3. ROOTING YOUR DEVICE:
Install This Magisk apk
- Download Patched Boot image (According to your device firmware) from the link and put them in MTK client folder.
- Now in pc type
python mtk w boot,vbmeta boot.patched,vbmeta.img.emptyhit enter - Then power off your phone and connect usb while holding both volume buttons (and don't leave them)
-
- Now disconnect and reboot phone
- Now open Magisk app
4. FLASHING TWRP RECOVERY:
- Download TWRP - From here and extract it.
- Download and install Flashify app
- Open Flashify and grant root permission
- Select Recovery image from the extracted twrp folder and install it
- After flashing is done click reboot now or you can reboot to recovery via magisk app
"
Credits:
- Me @Saksham Antil (aka Tony Stark) for this guide and Testing
- @Engrudhy for older guide
- @Skyhuppa for making TWRP
- Elias for finding out the way to ubl
- B Kerler fot MTKClient
If you face any issues lem me know down below111
