How To Guide [GUIDE][UNBRICK] Realme 8i/Narzo 50 Unbrick Free without Auth [RMX3151][RMX3286]

Search This thread

renatobab

New member
Dec 21, 2021
4
0
Hi, first of all thanks for a nice guide.

I've bricked my Realme 8i that had A30 Global stock firmware. Using this guide I was able to flash it with decrypted A32 Global that you provided here. Now the phone boots but touchscreen doesn't work(and possibly other things, not sure because I can't get past the Choose region screen, power and volume buttons work in the UI though).

I presume it should be flashed with A30 firmware not the A32? If so, could you help with merging the super.img? I've decrypted the stock A30 but don't know the information needed to merge it(partition size, etc).

Any other advice is welcome. Thank you.
 
Hi, first of all thanks for a nice guide.

I've bricked my Realme 8i that had A30 Global stock firmware. Using this guide I was able to flash it with decrypted A32 Global that you provided here. Now the phone boots but touchscreen doesn't work(and possibly other things, not sure because I can't get past the Choose region screen, power and volume buttons work in the UI though).

I presume it should be flashed with A30 firmware not the A32? If so, could you help with merging the super.img? I've decrypted the stock A30 but don't know the information needed to merge it(partition size, etc).

Any other advice is welcome. Thank you.
Yes let me give you tool to merge super image
 
Hi, first of all thanks for a nice guide.

I've bricked my Realme 8i that had A30 Global stock firmware. Using this guide I was able to flash it with decrypted A32 Global that you provided here. Now the phone boots but touchscreen doesn't work(and possibly other things, not sure because I can't get past the Choose region screen, power and volume buttons work in the UI though).

I presume it should be flashed with A30 firmware not the A32? If so, could you help with merging the super.img? I've decrypted the stock A30 but don't know the information needed to merge it(partition size, etc).

Any other advice is welcome. Thank you.
 

renatobab

New member
Dec 21, 2021
4
0

NBC ft85

New member
May 2, 2014
3
0
Realme 8i
Great job - and everything explained very clearly! Thank you very much for that.

For me, the bypass works so far and I can also flash with the SP tool - up to an image file: oplusreserve2.img. for this, SP Tool asks for a verified file or should I switch the verification off. If I leave the file away, it runs through. I am surprised that it doesn’t seem to appear here ?! What am I doing wrong?
 

Attachments

  • Screenshot 2021-12-25 125625.png
    Screenshot 2021-12-25 125625.png
    125.4 KB · Views: 54

Top Liked Posts

  • There are no posts matching your filters.
  • 2
    Hello everyone! So after the new mediatek DAA and SLA protection bypasses you can find github repo of here , using the bypass we are able to use SPFlash Tool, here is a guide how you can do it! This guide is for RMX3151 (Realme 8i) and RMX3286 (Narzo 50) ONLY. DON'T DO ANY OF THESE IF YOU HAVE SOMETHING ELSE!

    ALWAYS USE DOWNLOAD ONLY MODE OF SP FLASH TOOL.
    DON'T TOUCH ANYTHING RELATED TO FORMAT ON SP FLASH TOOL! (IT'S WRITTEN EVERYWHERE, YOU WILL LOSE YOUR IMEIS IF YOU USE FORMAT ALL + DOWNLOAD. YOU ARE SAFE IF YOU USE DOWNLOAD ONLY.)

    Windows Method

    Requirements:
    Bypass Tools Pack - (DRIVER AND BYPASS FILES)
    SP Flash Tool

    Decrypted OFP (OPPO FIRMWARE PACKAGE) Files:

    FULL FIRMWARE - INCLUDES THE "USERDATA" PARTITION, HENCE LARGER.
    A.32 (Indian) - Mega | GDrive
    A.32 (Global) - Mega | GDrive
    A.30 (Indian) - Mega | GDrive
    These firmwares are from Realme 8i but will work for Narzo 50 also (I will add Narzo 50 firmwares soon)

    Install Python from Windows Store
    libusb-win32 - Having Issues? Use this.
    Get usbdk installer (.msi) from here and install it

    1) Extract the zip
    2) Go to driver folder, find the .inf file right click and press install.
    1611352830350.png


    3)Download this file and install it, after installing power off phone and connect to pc while holding Vol+- (don't leave the buttons after connecting) . You might need this driver as well if it's not detected.

    3a6d351fec8ab9961a5e3.png


    Press next, connect your device to PC while holding Vol+- buttons (your device needs to be powered off, and don't leave the buttons) and you will see the mtkdriver down below. Install it.
    310b8508659201f6729f7.png


    Choose MediaTek USB Port and install it.
    4)Then run the brom.bat under Bypass folder.
    Screenshot (63).png


    5) Now power off the phone and connect the phone while holding volume + and - (Don't leave the buttons until the bypass is done)
    IMG_20211204_142400_352.png


    6)After the above step Go into Flash Tool folder and open the SPFlash tool go to Options>Option
    Screenshot (65).png


    Click on Connections and select UART and set Baud Rate to 921600
    Screenshot (68).png


    7) after that choose scatter file and also if not set, set your download-agent. You don't need to select auth file as authorization is disabled. Once you do it, it should look like this. ALWAYS MAKE SURE DOWNLOAD ONLY MODE IS SELECTED! DON'T SELECT OTHER MODES!
    IMG_20211204_141629_731.jpg


    Make SURE "Download Only" is selected. Don't select ANYTHING ELSE! You will lose your IMEIs, Serial Numbers, Capability of Hardware Attestation etc. if you choose "Format data + Download" make SURE you selected "Download Only".

    8) Uncheck oplusreserve2 first. Now, you can start downloading with the button and after that a checkmark will appear. You can reboot your phone and use it like before now! All your userdata will (inevitably) be cleared!

    After flashing it should look like this. Download has been complete. Enjoy!
    IMG_20211212_004225.png


    Notes :
    After this phone might not boot due to encryption, you can do any of the below procedures to format your data and boot your phone
    1. In case you can access recovery by holding volume and power button - Wipe all data from recovery and reboot

    2. In case you cannot access recovery, power off phone then enter this command in mtkclient :
    Code:
    python mtk e metadata,userdata,md_udc
    and connect phone while holding both volume buttons. After this just reboot phone

    Also note that first boot takes some time, so don't panic leave it for few minutes it'll boot :)

    Credits :
    https://github.com/bkerler/ for decryptor and for creating the tool.

    If you face any issues contact me here
    1
    Hi, I was able to flash my firmware and update it from A30 to A32 with this tutorial, but I feel that few things need to be clarified, because they weren't mentioned in the tutorial, so I had to learn some things by trial and error or use some different methods/tools:

    1. First of all this driver "New QcomMtk_Driver_Setup_V2.0.1.1_GsmMafia.Com.exe" is in chineese and when I tried to install it for the first time it took me over 20 minutes, I think. Also, it kinda "hanged" at the end of the installation and install window didn't respond to my clicks.

    2. I couldn't install this driver from "bypass toolpack" by just simple clicking "Install" on the menu. It wasn't working in my case, so I had to press <Win key> + R - then type "hdwwiz" without quotes - then it shows "Add hardware" wizard window. Using this wizard I could install the driver.

    3. I had to restart my computer and restart the phone after installing all drivers. Because when I initially didn't do it I had this error --> "usb_class - [LIB]: Couldn't get device configuration". So just remember to restart Windows before flashing :)

    4. This "brom.bat" bypass method didn't work in my case. Python was crashing on the end of sending payload and I couldn't do anything with it. I had to use tool "MTK Auth Bypass Tool V13" to make bypass work.

    5. I couldn't use powershell for mktclient commands. For some reason only command line was working correctly for me.

    6. On the end of the tutorial there is this step "After flashing it should look like this. Download has been complete. Enjoy!". But for my case it was not enough. My phone was still not booting correctly.
    I had to execute this command on the end "python mtk e metadata,userdata,md_udc" to make whole flashing work for my phone.
    1 to 5 is issue from your side only it seems... 6 is fine ..you need to format data if it doesn't boot.
    1
    Guys help. the caused of my phone realme 8i brick is (rooting without twrp) and caused Destroyed image. I can still open recovery mode but unauthorized when connecting. I found this step and followed it. but my problem now is
    View attachment 5579029
    Uncheck oplusreserve2 and then flash