• Introducing XDA Computing: Discussion zones for Hardware, Software, and more!    Check it out!

[GUIDE] Unlocking JioFi 3 JMR540 & JMR541 for all networks

Search This thread

Poojan Joshi

New member
Jul 26, 2021
2
0
I tried so many times and I finally upgraded the firmware but the Vi sim isn't showing any signal, it just shows detached.
View attachment 5373639
Hello,
Try changing the APN to www in network settings

Thank you

If it still not working than, JioFi only support Band 5 (850MHz), Band 3 (1800MHz) and Band 40 (2300MHz). So it could be possible that Vi is using different band.
 

mohammad_sham

Member
Apr 25, 2013
9
2
silchar
Unlocked Firmware for JioFi 3 JMR540 & JMR541

Disclaimer
I am not responsible for any kind of damage to your device.
Use this firmware at your own risk
Post is for educational purpose only.


ONLY FOR JMR 540 & JMR 541


I was able to dump and reverse engineer JioFi 3's firmware to see if I can unlock the SIM restrictions. JioFi 3 is designed by Foxconn it uses generic firmware. Unlocking took time though. Tested with Vi, Airtel.



Guide

Make sure you're on same firmware version
  • JMR 540 - FXN_JMR540_R6.16
  • JMR 541 - FXN_JMR541_R3.10
If not please use the device for sometime it'll autoupdate.


1. Locate your device model and download the respective Firmware and extract it to a known location


2. Install drivers and tools (skip if already installed)

  • Install Fastboot drivers ( google it for mac and linux it's easy to find)
  • Install Fastboot ( google it for mac and linux it's easy to find)

3. Prepare device

  • Remove battery from JioFi 3
  • Locate reset pin hole button
  • Lay down JioFi 3
  • Use Paper Clip / SIM Ejector Tool to press button inside (using sharp object is not recommended)
  • Keep pressing button down and insert USB cable
  • Release button as soon as all the LEDs in Display turns RED. This means device is in boot loader mode

4. Flashing Unlocked Firmware

  • Open adb and fastboot tools terminal
  • Enter following to check if device is connected

  • fastboot devices

  • It will return something like this
  • baxxxxx fastboot

  • This means device is connected. If your device doesn't show up here please check drivers in Device manager
  • Now first erase the system partition

  • fastboot erase system

  • It will return something like this
  • erasing 'system'... OKAY [ 1.104s] finished. total time: 1.105s

  • Now flash the firmware
  • fastboot flash system "D:\system.img" ( replace path )

  • It should return something like this
  • sending 'system' (34306 KB)... OKAY [ 1.276s] writing 'system'... OKAY [ 9.462s] finished. total time: 10.741s

  • Now send reboot command to device
  • fastboot reboot

  • You'll notice device will reboot normally now you can unplug the cable.

Congratulations your device is now unlocked and you can reinsert battery and another SIM for testing.

Firmware will take long time than usual to boot do not panic.

4. Changing APN
  • Insert SIM connect with JioFi 3 wait it to intialize
  • Open Web UI from browser (http://jiofi.local.html/)
  • Now login (default username/pwd is administrator/administrator)
  • In Network Tab you'll find setting for changing APN
  • Put it on manual and enter "internet" as APN (without quotes)
  • Hit apply/save device will reboot again automatically and it'll auto connect
  • Just wait patience is the key here it'll connect.

If something goes WRONG or you want to UNDO you can re flash original firmware which is provided in this post.


Original backup




FAQs

  1. Q. My device is not visible in fastboot devices
    A. Confirm driver installation a faulty cable can also be the issue.
    .
  2. Q. Everything went well but still no changes in dashboard
    A. After successful flash if you still don't see the changes your device is probably booting from recovery partition. Try flashing recovery partition by
    fastboot erase recoveryfs
    fastboot flash recoveryfs "D:\system.img"
    .


  3. Q. After resetting device from pin hole button it shows INVALID SIM.
    A. This is supposed to happen just reboot the device it'll work again.
    .
  4. Q. Can I undo all this and get back to original firmware
    A. Yes just flash the original firmware provided in post and reset the device.







Mentions:
Thanks to
Karuppusamy for testing it on JMR541.


What about JioFi 2, 4, 5, 6?
Reverse Engineering takes lot of time and coffee. Until I get physical access to device I won't be able to unlock it. I'm constantly searching them on OLX as soon as I get hands on I'll surely try to RE and unlock it. I'll update the same here if there is no update here at the time of your reading then I haven't got the device yet so please don't spam for update hope you understand that I don't get anything by doing these things, I do it for liberation of locked hardware to meet it's real destiny and of course for the people. I also have a day job so no I cannot guide or teach you, hope you understand why.



Hello brother,
Everything well went. Only I was stuck with the driver. At last the driver i got from windows update optional download. So all went smoothly without any stuck.
After reboot I inserted the Airtel sim and it got connected directly without any APN etc etc. I opened the localhost page and there i found that it taking airtelgprs APN.
Jiofi is working awsm now there is no issue.
But there is a small issue and that is I can't login the http://jiofi.local.html/.
administrator/administrator is not working and moreover I am trying with the id pwd given at the backside of the jiofi that is also not working.
please guide me so that in future I shouldn't stuck with this.
Thanks for the moded firmware.
 

vysakhs

New member
Aug 3, 2021
3
1
Thanks dude it worked with my jmr 540 device.
First I flashed with image file but it doesn't work,
Then I letter follow u r s instruction and deleted recovery and then again flashed recovery then it worked fluently
Screenshot_2021-08-05-01-22-03-31.png
 
  • Like
Reactions: abhimortal6

xyzqwerty500

Member
Oct 10, 2020
39
1
Hey abhi mortal I am not an engineer but I want to unlockmy jiofi 2 I can send you one If u can reverse engineer it .. I have 2 models M2 and M2s or plzz can you make a detailed video on how you reverse engineered it thanks
I can help you with that and also unlock 3g by editing build.prop. You just need to add one line. But first share the screenshot of network Tab. What all can be done from the Web UI, i need to check?
 
  • Like
Reactions: avinash2801

Arun1999

New member
Jun 22, 2018
3
0
Hi. I recently flashed your system img its working well. Thanks. But i want to know is it upgradable, i want to turn off jiofi 3 auto firmware updates. And please also release steps how to crack system firmware so that we can use latest firmware with all sim support.
 

biniya

New member
Aug 7, 2021
1
0
Hi
i was trying to unlock JMR41
All process were done successfully but no network with vodafone sim but still working jio sim
i do one more time and now after flashing device Try flashing recovery partition too
butt stiil no network ( vodafone 4g network is vorking my phone )
please help me to solve this
 

Attachments

  • jj.jpg
    jj.jpg
    100.3 KB · Views: 15

Top Liked Posts

  • There are no posts matching your filters.
  • 1
    thanks bro, it works for my JioFi 3, JMR541.
    1
    plss help i'm stuck in bootloop
    You should've backed it up first before experimenting.
    1
    Unlocked Firmware for JioFi 3 JMR540 & JMR541

    Disclaimer
    I am not responsible for any kind of damage to your device.
    Use this firmware at your own risk
    Post is for educational purpose only.


    ONLY FOR JMR 540 & JMR 541


    I was able to dump and reverse engineer JioFi 3's firmware to see if I can unlock the SIM restrictions. JioFi 3 is designed by Foxconn it uses generic firmware. Unlocking took time though. Tested with Vi, Airtel.



    Guide

    Make sure you're on same firmware version
    • JMR 540 - FXN_JMR540_R6.16
    • JMR 541 - FXN_JMR541_R3.10
    If not please use the device for sometime it'll autoupdate.


    1. Locate your device model and download the respective Firmware and extract it to a known location


    2. Install drivers and tools (skip if already installed)

    • Install Fastboot drivers ( google it for mac and linux it's easy to find)
    • Install Fastboot ( google it for mac and linux it's easy to find)

    3. Prepare device

    • Remove battery from JioFi 3
    • Locate reset pin hole button
    • Lay down JioFi 3
    • Use Paper Clip / SIM Ejector Tool to press button inside (using sharp object is not recommended)
    • Keep pressing button down and insert USB cable
    • Release button as soon as all the LEDs in Display turns RED. This means device is in boot loader mode

    4. Flashing Unlocked Firmware

    • Open adb and fastboot tools terminal
    • Enter following to check if device is connected

    • fastboot devices

    • It will return something like this
    • baxxxxx fastboot

    • This means device is connected. If your device doesn't show up here please check drivers in Device manager
    • Now first erase the system partition

    • fastboot erase system

    • It will return something like this
    • erasing 'system'... OKAY [ 1.104s] finished. total time: 1.105s

    • Now flash the firmware
    • fastboot flash system "D:\system.img" ( replace path )

    • It should return something like this
    • sending 'system' (34306 KB)... OKAY [ 1.276s] writing 'system'... OKAY [ 9.462s] finished. total time: 10.741s

    • Now send reboot command to device
    • fastboot reboot

    • You'll notice device will reboot normally now you can unplug the cable.

    Congratulations your device is now unlocked and you can reinsert battery and another SIM for testing.

    Firmware will take long time than usual to boot do not panic.

    4. Changing APN
    • Insert SIM connect with JioFi 3 wait it to intialize
    • Open Web UI from browser (http://jiofi.local.html/)
    • Now login (default username/pwd is administrator/administrator)
    • In Network Tab you'll find setting for changing APN
    • Put it on manual and enter "internet" as APN (without quotes)
    • Hit apply/save device will reboot again automatically and it'll auto connect
    • Just wait patience is the key here it'll connect.

    If something goes WRONG or you want to UNDO you can re flash original firmware which is provided in this post.


    Original backup




    FAQs

    1. Q. My device is not visible in fastboot devices
      A. Confirm driver installation a faulty cable can also be the issue.
      .
    2. Q. Everything went well but still no changes in dashboard
      A. After successful flash if you still don't see the changes your device is probably booting from recovery partition. Try flashing recovery partition by
      fastboot erase recoveryfs
      fastboot flash recoveryfs "D:\system.img"
      .


    3. Q. After resetting device from pin hole button it shows INVALID SIM.
      A. This is supposed to happen just reboot the device it'll work again.
      .
    4. Q. Can I undo all this and get back to original firmware
      A. Yes just flash the original firmware provided in post and reset the device.







    Mentions:
    Thanks to
    Karuppusamy for testing it on JMR541.


    What about JioFi 2, 4, 5, 6?
    Reverse Engineering takes lot of time and coffee. Until I get physical access to device I won't be able to unlock it. I'm constantly searching them on OLX as soon as I get hands on I'll surely try to RE and unlock it. I'll update the same here if there is no update here at the time of your reading then I haven't got the device yet so please don't spam for update hope you understand that I don't get anything by doing these things, I do it for liberation of locked hardware to meet it's real destiny and of course for the people. I also have a day job so no I cannot guide or teach you, hope you understand why.



    How to change Band in Jiofi ye bhi bata do please, band kaise Chang kare, Vi me band 3 connect hota agar band 41 connect ho to kaise kare please bhai
    1
    Connect the device to pc via USB and access the web panel inorder to change the password Incase your forgot your wifi password.
    How to reset password if i forget the once changed password already of jiofi 3
    I tried reset button but it doesn't reset it because i changed it on the jiofi website now i forgot the password that i changed a long ago and i can't connect my jiofi 3 so i can't change it.? Is there any other way for it?
  • 30
    Unlocked Firmware for JioFi 3 JMR540 & JMR541

    Disclaimer
    I am not responsible for any kind of damage to your device.
    Use this firmware at your own risk
    Post is for educational purpose only.


    ONLY FOR JMR 540 & JMR 541


    I was able to dump and reverse engineer JioFi 3's firmware to see if I can unlock the SIM restrictions. JioFi 3 is designed by Foxconn it uses generic firmware. Unlocking took time though. Tested with Vi, Airtel.



    Guide

    Make sure you're on same firmware version
    • JMR 540 - FXN_JMR540_R6.16
    • JMR 541 - FXN_JMR541_R3.10
    If not please use the device for sometime it'll autoupdate.


    1. Locate your device model and download the respective Firmware and extract it to a known location


    2. Install drivers and tools (skip if already installed)

    • Install Fastboot drivers ( google it for mac and linux it's easy to find)
    • Install Fastboot ( google it for mac and linux it's easy to find)

    3. Prepare device

    • Remove battery from JioFi 3
    • Locate reset pin hole button
    • Lay down JioFi 3
    • Use Paper Clip / SIM Ejector Tool to press button inside (using sharp object is not recommended)
    • Keep pressing button down and insert USB cable
    • Release button as soon as all the LEDs in Display turns RED. This means device is in boot loader mode

    4. Flashing Unlocked Firmware

    • Open adb and fastboot tools terminal
    • Enter following to check if device is connected

    • fastboot devices

    • It will return something like this
    • baxxxxx fastboot

    • This means device is connected. If your device doesn't show up here please check drivers in Device manager
    • Now first erase the system partition

    • fastboot erase system

    • It will return something like this
    • erasing 'system'... OKAY [ 1.104s] finished. total time: 1.105s

    • Now flash the firmware
    • fastboot flash system "D:\system.img" ( replace path )

    • It should return something like this
    • sending 'system' (34306 KB)... OKAY [ 1.276s] writing 'system'... OKAY [ 9.462s] finished. total time: 10.741s

    • Now send reboot command to device
    • fastboot reboot

    • You'll notice device will reboot normally now you can unplug the cable.

    Congratulations your device is now unlocked and you can reinsert battery and another SIM for testing.

    Firmware will take long time than usual to boot do not panic.

    4. Changing APN
    • Insert SIM connect with JioFi 3 wait it to intialize
    • Open Web UI from browser (http://jiofi.local.html/)
    • Now login (default username/pwd is administrator/administrator)
    • In Network Tab you'll find setting for changing APN
    • Put it on manual and enter "internet" as APN (without quotes)
    • Hit apply/save device will reboot again automatically and it'll auto connect
    • Just wait patience is the key here it'll connect.

    If something goes WRONG or you want to UNDO you can re flash original firmware which is provided in this post.


    Original backup




    FAQs

    1. Q. My device is not visible in fastboot devices
      A. Confirm driver installation a faulty cable can also be the issue.
      .
    2. Q. Everything went well but still no changes in dashboard
      A. After successful flash if you still don't see the changes your device is probably booting from recovery partition. Try flashing recovery partition by
      fastboot erase recoveryfs
      fastboot flash recoveryfs "D:\system.img"
      .


    3. Q. After resetting device from pin hole button it shows INVALID SIM.
      A. This is supposed to happen just reboot the device it'll work again.
      .
    4. Q. Can I undo all this and get back to original firmware
      A. Yes just flash the original firmware provided in post and reset the device.







    Mentions:
    Thanks to
    Karuppusamy for testing it on JMR541.


    What about JioFi 2, 4, 5, 6?
    Reverse Engineering takes lot of time and coffee. Until I get physical access to device I won't be able to unlock it. I'm constantly searching them on OLX as soon as I get hands on I'll surely try to RE and unlock it. I'll update the same here if there is no update here at the time of your reading then I haven't got the device yet so please don't spam for update hope you understand that I don't get anything by doing these things, I do it for liberation of locked hardware to meet it's real destiny and of course for the people. I also have a day job so no I cannot guide or teach you, hope you understand why.



    3
    bro is unlocking more 4g bands or manual selection of bands can be done ?
    Totally possible even 3G but it can't be done through WebUI it'll requires shell access.
    2
    1622625406032.jpeg

    This is completely genius! I am now able to use Airtel sim on my JioFi! Thanks!
    1
    successfully unlocked my jiofi 3 JMR541. tested with voda and its working well and good. Thanks a ton for this bro.
    I was late in checking this thread and got shipped airtel unlocked mifi from home.
    1
    successfully unlocked my jiofi 3 JMR541. tested with voda and its working well and good. Thanks a ton for this bro.
    I was late in checking this thread and got shipped airtel unlocked mifi from home.
    Can you show us dashboard screenshot. This will help other users to verify