[GUIDE][UPDATED] Unlocking JioFi 3 JMR540 & JMR541 for all networks

Search This thread

saurabh0310

New member
May 30, 2013
4
1
View attachment 5327257
This is completely genius! I am now able to use Airtel sim on my JioFi! Thanks!
Unlocked Firmware for JioFi 3 JMR540 & JMR541

Disclaimer
I am not responsible for any kind of damage to your device.
Use this firmware at your own risk
Post is for educational purpose only.


ONLY FOR JMR 540 & JMR 541


I was able to dump and reverse engineer JioFi 3's firmware to see if I can unlock the SIM restrictions. JioFi 3 is designed by Foxconn it uses generic firmware. Unlocking took time though. Tested with Vi, Airtel.

UPDATE 17-10-21: Jio pushed a firmware update which is locking boot loader. If your device is not updated yet it is advised to re-flash your firmware with patched image given below which basically disables auto updates. If you're already locked out, currently there's no easy fix for that.

If you haven't used your device from a long time or you're still on lower or equal version than below it is advised not to use JioFi with SIM, flash this firmware first if you want to test SIM unlock.




Guide

Make sure you're on same or lower firmware version
  • JMR 540 - FXN_JMR540_R6.16
  • JMR 541 - FXN_JMR541_R3.10



1. Locate your device model and download the respective Firmware and extract it to a known location

2. Install drivers and tools (skip if already installed)

  • Install Fastboot drivers ( google it for mac and linux it's easy to find)
  • Install Fastboot ( google it for mac and linux it's easy to find)

3. Prepare device

  • Remove battery from JioFi 3
  • Locate reset pin hole button
  • Lay down JioFi 3
  • Use Paper Clip / SIM Ejector Tool to press button inside (using sharp object is not recommended)
  • Keep pressing button down and insert USB cable
  • Release button as soon as all the LEDs in Display turns RED. This means device is in boot loader mode

4. Flashing Unlocked Firmware

  • Open adb and fastboot tools terminal
  • Enter following to check if device is connected

  • fastboot devices

  • It will return something like this
  • baxxxxx fastboot

  • This means device is connected. If your device doesn't show up here please check drivers in Device manager
  • Now first erase the system partition

  • fastboot erase system

  • It will return something like this
  • erasing 'system'... OKAY [ 1.104s] finished. total time: 1.105s

  • Now flash the firmware
  • fastboot flash system "D:\system.img" ( replace path )

  • It should return something like this
  • sending 'system' (34306 KB)... OKAY [ 1.276s] writing 'system'... OKAY [ 9.462s] finished. total time: 10.741s

  • Now send reboot command to device
  • fastboot reboot

  • You'll notice device will reboot normally now you can unplug the cable.

Congratulations your device is now unlocked and you can reinsert battery and another SIM for testing.

Firmware will take long time than usual to boot do not panic.

4. Changing APN
  • Insert SIM connect with JioFi 3 wait it to intialize
  • Open Web UI from browser (http://jiofi.local.html/)
  • Now login (default username/pwd is administrator/administrator)
  • In Network Tab you'll find setting for changing APN
  • Put it on manual and enter "internet" as APN (without quotes)
  • Hit apply/save device will reboot again automatically and it'll auto connect
  • Just wait patience is the key here it'll connect.

If something goes WRONG or you want to UNDO you can re flash original firmware which is provided in this post.


Original backup




FAQs

  1. Q. My device is not visible in fastboot devices
    A. Confirm driver installation a faulty cable can also be the issue.
    .
  2. Q. Everything went well but still no changes in dashboard
    A. After successful flash if you still don't see the changes your device is probably booting from recovery partition. Try flashing recovery partition by
    fastboot erase recoveryfs
    fastboot flash recoveryfs "D:\system.img"
    .


  3. Q. After resetting device from pin hole button it shows INVALID SIM.
    A. This is supposed to happen just reboot the device it'll work again.
    .
  4. Q. Can I undo all this and get back to original firmware
    A. Yes just flash the original firmware provided in post and reset the device.
    .
  5. Q. I 'accidentally' flashed my recovery and boot partition
    A. Well accidentally I've backed up recovery and boot download from below

    1.
    JMR540_boot_recovery.rar
    2. JMR541_boot_recovery.rar
    .
  6. Q. FAILED: (remote: Image is locked) issue while erasing/flashing image
    A. Jio recently pushed an firmware update which re-locks simlock and bootloader which basically means you can't flash unsigned/custom firmware. Currently there is no fix.







Mentions:
Thanks to
Karuppusamy for testing it on JMR541.


What about JioFi 2, 4, 5, 6?
Reverse Engineering takes lot of time and coffee. Until I get physical access to device I won't be able to unlock it. I'm constantly searching them on OLX as soon as I get hands on I'll surely try to RE and unlock it. I'll update the same here if there is no update here at the time of your reading then I haven't got the device yet so please don't spam for update hope you understand that I don't get anything by doing these things, I do it for liberation of locked hardware to meet it's real destiny and of course for the people. I also have a day job so no I cannot guide or teach you, hope you understand why.



My Device is Connected.. but its not showing in ADB Command ..
1646296519541.png

its showing waiting for device..
what can be the reason..????
 

jgour

New member
Apr 1, 2022
1
0
Hyderabad
Unlocked Firmware for JioFi 3 JMR540 & JMR541

Disclaimer
I am not responsible for any kind of damage to your device.
Use this firmware at your own risk
Post is for educational purpose only.


ONLY FOR JMR 540 & JMR 541


I was able to dump and reverse engineer JioFi 3's firmware to see if I can unlock the SIM restrictions. JioFi 3 is designed by Foxconn it uses generic firmware. Unlocking took time though. Tested with Vi, Airtel.

UPDATE 17-10-21: Jio pushed a firmware update which is locking boot loader. If your device is not updated yet it is advised to re-flash your firmware with patched image given below which basically disables auto updates. If you're already locked out, currently there's no easy fix for that.

If you haven't used your device from a long time or you're still on lower or equal version than below it is advised not to use JioFi with SIM, flash this firmware first if you want to test SIM unlock.




Guide

Make sure you're on same or lower firmware version
  • JMR 540 - FXN_JMR540_R6.16
  • JMR 541 - FXN_JMR541_R3.10



1. Locate your device model and download the respective Firmware and extract it to a known location

2. Install drivers and tools (skip if already installed)

  • Install Fastboot drivers ( google it for mac and linux it's easy to find)
  • Install Fastboot ( google it for mac and linux it's easy to find)

3. Prepare device

  • Remove battery from JioFi 3
  • Locate reset pin hole button
  • Lay down JioFi 3
  • Use Paper Clip / SIM Ejector Tool to press button inside (using sharp object is not recommended)
  • Keep pressing button down and insert USB cable
  • Release button as soon as all the LEDs in Display turns RED. This means device is in boot loader mode

4. Flashing Unlocked Firmware

  • Open adb and fastboot tools terminal
  • Enter following to check if device is connected

  • fastboot devices

  • It will return something like this
  • baxxxxx fastboot

  • This means device is connected. If your device doesn't show up here please check drivers in Device manager
  • Now first erase the system partition

  • fastboot erase system

  • It will return something like this
  • erasing 'system'... OKAY [ 1.104s] finished. total time: 1.105s

  • Now flash the firmware
  • fastboot flash system "D:\system.img" ( replace path )

  • It should return something like this
  • sending 'system' (34306 KB)... OKAY [ 1.276s] writing 'system'... OKAY [ 9.462s] finished. total time: 10.741s

  • Now send reboot command to device
  • fastboot reboot

  • You'll notice device will reboot normally now you can unplug the cable.

Congratulations your device is now unlocked and you can reinsert battery and another SIM for testing.

Firmware will take long time than usual to boot do not panic.

4. Changing APN
  • Insert SIM connect with JioFi 3 wait it to intialize
  • Open Web UI from browser (http://jiofi.local.html/)
  • Now login (default username/pwd is administrator/administrator)
  • In Network Tab you'll find setting for changing APN
  • Put it on manual and enter "internet" as APN (without quotes)
  • Hit apply/save device will reboot again automatically and it'll auto connect
  • Just wait patience is the key here it'll connect.

If something goes WRONG or you want to UNDO you can re flash original firmware which is provided in this post.


Original backup




FAQs

  1. Q. My device is not visible in fastboot devices
    A. Confirm driver installation a faulty cable can also be the issue.
    .
  2. Q. Everything went well but still no changes in dashboard
    A. After successful flash if you still don't see the changes your device is probably booting from recovery partition. Try flashing recovery partition by
    fastboot erase recoveryfs
    fastboot flash recoveryfs "D:\system.img"
    .


  3. Q. After resetting device from pin hole button it shows INVALID SIM.
    A. This is supposed to happen just reboot the device it'll work again.
    .
  4. Q. Can I undo all this and get back to original firmware
    A. Yes just flash the original firmware provided in post and reset the device.
    .
  5. Q. I 'accidentally' flashed my recovery and boot partition
    A. Well accidentally I've backed up recovery and boot download from below

    1.
    JMR540_boot_recovery.rar
    2. JMR541_boot_recovery.rar
    .
  6. Q. FAILED: (remote: Image is locked) issue while erasing/flashing image
    A. Jio recently pushed an firmware update which re-locks simlock and bootloader which basically means you can't flash unsigned/custom firmware. Currently there is no fix.







Mentions:
Thanks to
Karuppusamy for testing it on JMR541.


What about JioFi 2, 4, 5, 6?
Reverse Engineering takes lot of time and coffee. Until I get physical access to device I won't be able to unlock it. I'm constantly searching them on OLX as soon as I get hands on I'll surely try to RE and unlock it. I'll update the same here if there is no update here at the time of your reading then I haven't got the device yet so please don't spam for update hope you understand that I don't get anything by doing these things, I do it for liberation of locked hardware to meet it's real destiny and of course for the people. I also have a day job so no I cannot guide or teach you, hope you understand why.



1648841336512.png


can't able to erase the system partition, please help.
 

Nizamu

New member
Sep 1, 2021
2
0
Unlocked Firmware for JioFi 3 JMR540 & JMR541

Disclaimer
I am not responsible for any kind of damage to your device.
Use this firmware at your own risk
Post is for educational purpose only.


ONLY FOR JMR 540 & JMR 541


I was able to dump and reverse engineer JioFi 3's firmware to see if I can unlock the SIM restrictions. JioFi 3 is designed by Foxconn it uses generic firmware. Unlocking took time though. Tested with Vi, Airtel.

UPDATE 17-10-21: Jio pushed a firmware update which is locking boot loader. If your device is not updated yet it is advised to re-flash your firmware with patched image given below which basically disables auto updates. If you're already locked out, currently there's no easy fix for that.

If you haven't used your device from a long time or you're still on lower or equal version than below it is advised not to use JioFi with SIM, flash this firmware first if you want to test SIM unlock.




Guide

Make sure you're on same or lower firmware version
  • JMR 540 - FXN_JMR540_R6.16
  • JMR 541 - FXN_JMR541_R3.10



1. Locate your device model and download the respective Firmware and extract it to a known location

2. Install drivers and tools (skip if already installed)

  • Install Fastboot drivers ( google it for mac and linux it's easy to find)
  • Install Fastboot ( google it for mac and linux it's easy to find)

3. Prepare device

  • Remove battery from JioFi 3
  • Locate reset pin hole button
  • Lay down JioFi 3
  • Use Paper Clip / SIM Ejector Tool to press button inside (using sharp object is not recommended)
  • Keep pressing button down and insert USB cable
  • Release button as soon as all the LEDs in Display turns RED. This means device is in boot loader mode

4. Flashing Unlocked Firmware

  • Open adb and fastboot tools terminal
  • Enter following to check if device is connected

  • fastboot devices

  • It will return something like this
  • baxxxxx fastboot

  • This means device is connected. If your device doesn't show up here please check drivers in Device manager
  • Now first erase the system partition

  • fastboot erase system

  • It will return something like this
  • erasing 'system'... OKAY [ 1.104s] finished. total time: 1.105s

  • Now flash the firmware
  • fastboot flash system "D:\system.img" ( replace path )

  • It should return something like this
  • sending 'system' (34306 KB)... OKAY [ 1.276s] writing 'system'... OKAY [ 9.462s] finished. total time: 10.741s

  • Now send reboot command to device
  • fastboot reboot

  • You'll notice device will reboot normally now you can unplug the cable.

Congratulations your device is now unlocked and you can reinsert battery and another SIM for testing.

Firmware will take long time than usual to boot do not panic.

4. Changing APN
  • Insert SIM connect with JioFi 3 wait it to intialize
  • Open Web UI from browser (http://jiofi.local.html/)
  • Now login (default username/pwd is administrator/administrator)
  • In Network Tab you'll find setting for changing APN
  • Put it on manual and enter "internet" as APN (without quotes)
  • Hit apply/save device will reboot again automatically and it'll auto connect
  • Just wait patience is the key here it'll connect.

If something goes WRONG or you want to UNDO you can re flash original firmware which is provided in this post.


Original backup




FAQs

  1. Q. My device is not visible in fastboot devices
    A. Confirm driver installation a faulty cable can also be the issue.
    .
  2. Q. Everything went well but still no changes in dashboard
    A. After successful flash if you still don't see the changes your device is probably booting from recovery partition. Try flashing recovery partition by
    fastboot erase recoveryfs
    fastboot flash recoveryfs "D:\system.img"
    .


  3. Q. After resetting device from pin hole button it shows INVALID SIM.
    A. This is supposed to happen just reboot the device it'll work again.
    .
  4. Q. Can I undo all this and get back to original firmware
    A. Yes just flash the original firmware provided in post and reset the device.
    .
  5. Q. I 'accidentally' flashed my recovery and boot partition
    A. Well accidentally I've backed up recovery and boot download from below

    1.
    JMR540_boot_recovery.rar
    2. JMR541_boot_recovery.rar
    .
  6. Q. FAILED: (remote: Image is locked) issue while erasing/flashing image
    A. Jio recently pushed an firmware update which re-locks simlock and bootloader which basically means you can't flash unsigned/custom firmware. Currently there is no fix.







Mentions:
Thanks to
Karuppusamy for testing it on JMR541.


What about JioFi 2, 4, 5, 6?
Reverse Engineering takes lot of time and coffee. Until I get physical access to device I won't be able to unlock it. I'm constantly searching them on OLX as soon as I get hands on I'll surely try to RE and unlock it. I'll update the same here if there is no update here at the time of your reading then I haven't got the device yet so please don't spam for update hope you understand that I don't get anything by doing these things, I do it for liberation of locked hardware to meet it's real destiny and of course for the people. I also have a day job so no I cannot guide or teach you, hope you understand why.



Can anyone help .. please
Unlocked Firmware for JioFi 3 JMR540 & JMR541

Disclaimer
I am not responsible for any kind of damage to your device.
Use this firmware at your own risk
Post is for educational purpose only.


ONLY FOR JMR 540 & JMR 541


I was able to dump and reverse engineer JioFi 3's firmware to see if I can unlock the SIM restrictions. JioFi 3 is designed by Foxconn it uses generic firmware. Unlocking took time though. Tested with Vi, Airtel.

UPDATE 17-10-21: Jio pushed a firmware update which is locking boot loader. If your device is not updated yet it is advised to re-flash your firmware with patched image given below which basically disables auto updates. If you're already locked out, currently there's no easy fix for that.

If you haven't used your device from a long time or you're still on lower or equal version than below it is advised not to use JioFi with SIM, flash this firmware first if you want to test SIM unlock.




Guide

Make sure you're on same or lower firmware version
  • JMR 540 - FXN_JMR540_R6.16
  • JMR 541 - FXN_JMR541_R3.10



1. Locate your device model and download the respective Firmware and extract it to a known location

2. Install drivers and tools (skip if already installed)

  • Install Fastboot drivers ( google it for mac and linux it's easy to find)
  • Install Fastboot ( google it for mac and linux it's easy to find)

3. Prepare device

  • Remove battery from JioFi 3
  • Locate reset pin hole button
  • Lay down JioFi 3
  • Use Paper Clip / SIM Ejector Tool to press button inside (using sharp object is not recommended)
  • Keep pressing button down and insert USB cable
  • Release button as soon as all the LEDs in Display turns RED. This means device is in boot loader mode

4. Flashing Unlocked Firmware

  • Open adb and fastboot tools terminal
  • Enter following to check if device is connected

  • fastboot devices

  • It will return something like this
  • baxxxxx fastboot

  • This means device is connected. If your device doesn't show up here please check drivers in Device manager
  • Now first erase the system partition

  • fastboot erase system

  • It will return something like this
  • erasing 'system'... OKAY [ 1.104s] finished. total time: 1.105s

  • Now flash the firmware
  • fastboot flash system "D:\system.img" ( replace path )

  • It should return something like this
  • sending 'system' (34306 KB)... OKAY [ 1.276s] writing 'system'... OKAY [ 9.462s] finished. total time: 10.741s

  • Now send reboot command to device
  • fastboot reboot

  • You'll notice device will reboot normally now you can unplug the cable.

Congratulations your device is now unlocked and you can reinsert battery and another SIM for testing.

Firmware will take long time than usual to boot do not panic.

4. Changing APN
  • Insert SIM connect with JioFi 3 wait it to intialize
  • Open Web UI from browser (http://jiofi.local.html/)
  • Now login (default username/pwd is administrator/administrator)
  • In Network Tab you'll find setting for changing APN
  • Put it on manual and enter "internet" as APN (without quotes)
  • Hit apply/save device will reboot again automatically and it'll auto connect
  • Just wait patience is the key here it'll connect.

If something goes WRONG or you want to UNDO you can re flash original firmware which is provided in this post.


Original backup




FAQs

  1. Q. My device is not visible in fastboot devices
    A. Confirm driver installation a faulty cable can also be the issue.
    .
  2. Q. Everything went well but still no changes in dashboard
    A. After successful flash if you still don't see the changes your device is probably booting from recovery partition. Try flashing recovery partition by
    fastboot erase recoveryfs
    fastboot flash recoveryfs "D:\system.img"
    .


  3. Q. After resetting device from pin hole button it shows INVALID SIM.
    A. This is supposed to happen just reboot the device it'll work again.
    .
  4. Q. Can I undo all this and get back to original firmware
    A. Yes just flash the original firmware provided in post and reset the device.
    .
  5. Q. I 'accidentally' flashed my recovery and boot partition
    A. Well accidentally I've backed up recovery and boot download from below

    1.
    JMR540_boot_recovery.rar
    2. JMR541_boot_recovery.rar
    .
  6. Q. FAILED: (remote: Image is locked) issue while erasing/flashing image
    A. Jio recently pushed an firmware update which re-locks simlock and bootloader which basically means you can't flash unsigned/custom firmware. Currently there is no fix.







Mentions:
Thanks to
Karuppusamy for testing it on JMR541.


What about JioFi 2, 4, 5, 6?
Reverse Engineering takes lot of time and coffee. Until I get physical access to device I won't be able to unlock it. I'm constantly searching them on OLX as soon as I get hands on I'll surely try to RE and unlock it. I'll update the same here if there is no update here at the time of your reading then I haven't got the device yet so please don't spam for update hope you understand that I don't get anything by doing these things, I do it for liberation of locked hardware to meet it's real destiny and of course for the people. I also have a day job so no I cannot guide or teach you, hope you understand why.



Abi sir or anyone please help I can't do anything now . full red colour blinking always and it is not staying in fastboot mode always it start blinking i tried installing stock firmware that too not working sir😟


i know you are busy man please help if you are reading this when free
 

naidu

New member
Oct 28, 2012
1
0
Thank you very for this tweak. if you add BSNL 4G SIM also it would be great. in the mart BSNL planes are better than other vendors
 

horsementhewar

New member
Nov 13, 2016
2
0
Pune
hi abhimortal6, great to see that you're so active on forum and responding to each post.
I have JioFi6 JMR815 are you aware of how to get original firmware and do you got any luck in cracking its firmware. I want unlocked zip for jmr815, if you can please share the link or plans.
Thanks
 

bittu1910

New member
May 2, 2022
1
0
I have jiofi jmr1040(black). Can I help you in anyway without physically sending you the device?
 

avijit0503

New member
Apr 29, 2022
2
0
Unlocked Firmware for JioFi 3 JMR540 & JMR541

Disclaimer
I am not responsible for any kind of damage to your device.
Use this firmware at your own risk
Post is for educational purpose only.


ONLY FOR JMR 540 & JMR 541


I was able to dump and reverse engineer JioFi 3's firmware to see if I can unlock the SIM restrictions. JioFi 3 is designed by Foxconn it uses generic firmware. Unlocking took time though. Tested with Vi, Airtel.

UPDATE 17-10-21: Jio pushed a firmware update which is locking boot loader. If your device is not updated yet it is advised to re-flash your firmware with patched image given below which basically disables auto updates. If you're already locked out, currently there's no easy fix for that.

If you haven't used your device from a long time or you're still on lower or equal version than below it is advised not to use JioFi with SIM, flash this firmware first if you want to test SIM unlock.




Guide

Make sure you're on same or lower firmware version
  • JMR 540 - FXN_JMR540_R6.16
  • JMR 541 - FXN_JMR541_R3.10



1. Locate your device model and download the respective Firmware and extract it to a known location

2. Install drivers and tools (skip if already installed)

  • Install Fastboot drivers ( google it for mac and linux it's easy to find)
  • Install Fastboot ( google it for mac and linux it's easy to find)

3. Prepare device

  • Remove battery from JioFi 3
  • Locate reset pin hole button
  • Lay down JioFi 3
  • Use Paper Clip / SIM Ejector Tool to press button inside (using sharp object is not recommended)
  • Keep pressing button down and insert USB cable
  • Release button as soon as all the LEDs in Display turns RED. This means device is in boot loader mode

4. Flashing Unlocked Firmware

  • Open adb and fastboot tools terminal
  • Enter following to check if device is connected

  • fastboot devices

  • It will return something like this
  • baxxxxx fastboot

  • This means device is connected. If your device doesn't show up here please check drivers in Device manager
  • Now first erase the system partition

  • fastboot erase system

  • It will return something like this
  • erasing 'system'... OKAY [ 1.104s] finished. total time: 1.105s

  • Now flash the firmware
  • fastboot flash system "D:\system.img" ( replace path )

  • It should return something like this
  • sending 'system' (34306 KB)... OKAY [ 1.276s] writing 'system'... OKAY [ 9.462s] finished. total time: 10.741s

  • Now send reboot command to device
  • fastboot reboot

  • You'll notice device will reboot normally now you can unplug the cable.

Congratulations your device is now unlocked and you can reinsert battery and another SIM for testing.

Firmware will take long time than usual to boot do not panic.

4. Changing APN
  • Insert SIM connect with JioFi 3 wait it to intialize
  • Open Web UI from browser (http://jiofi.local.html/)
  • Now login (default username/pwd is administrator/administrator)
  • In Network Tab you'll find setting for changing APN
  • Put it on manual and enter "internet" as APN (without quotes)
  • Hit apply/save device will reboot again automatically and it'll auto connect
  • Just wait patience is the key here it'll connect.

If something goes WRONG or you want to UNDO you can re flash original firmware which is provided in this post.


Original backup




FAQs

  1. Q. My device is not visible in fastboot devices
    A. Confirm driver installation a faulty cable can also be the issue.
    .
  2. Q. Everything went well but still no changes in dashboard
    A. After successful flash if you still don't see the changes your device is probably booting from recovery partition. Try flashing recovery partition by
    fastboot erase recoveryfs
    fastboot flash recoveryfs "D:\system.img"
    .


  3. Q. After resetting device from pin hole button it shows INVALID SIM.
    A. This is supposed to happen just reboot the device it'll work again.
    .
  4. Q. Can I undo all this and get back to original firmware
    A. Yes just flash the original firmware provided in post and reset the device.
    .
  5. Q. I 'accidentally' flashed my recovery and boot partition
    A. Well accidentally I've backed up recovery and boot download from below

    1.
    JMR540_boot_recovery.rar
    2. JMR541_boot_recovery.rar
    .
  6. Q. FAILED: (remote: Image is locked) issue while erasing/flashing image
    A. Jio recently pushed an firmware update which re-locks simlock and bootloader which basically means you can't flash unsigned/custom firmware. Currently there is no fix.







Mentions:
Thanks to
Karuppusamy for testing it on JMR541.


What about JioFi 2, 4, 5, 6?
Reverse Engineering takes lot of time and coffee. Until I get physical access to device I won't be able to unlock it. I'm constantly searching them on OLX as soon as I get hands on I'll surely try to RE and unlock it. I'll update the same here if there is no update here at the time of your reading then I haven't got the device yet so please don't spam for update hope you understand that I don't get anything by doing these things, I do it for liberation of locked hardware to meet it's real destiny and of course for the people. I also have a day job so no I cannot guide or teach you, hope you understand why.



My name is Avijit Biswas
Successfully change jio file 540 ROM after then did not work vi sim (Vodafone network)

*Sim card LTE Status
Connection Status:
Detached

Can anyone help me with this? What's wrong with me not getting the network?
 

Attachments

  • Screenshot_2022-05-16-09-04-14-222_com.android.chrome.jpg
    Screenshot_2022-05-16-09-04-14-222_com.android.chrome.jpg
    293.8 KB · Views: 22
  • Screenshot_2022-05-16-09-04-04-465_com.android.chrome.jpg
    Screenshot_2022-05-16-09-04-04-465_com.android.chrome.jpg
    205.5 KB · Views: 21

avijit0503

New member
Apr 29, 2022
2
0
Thank you bro it is work properly
My new vi sim but old sim card not support
I well very happy to use this my jio fy 540
 

Rajan06

New member
Jun 12, 2022
2
0
Hi,
Today I have flash the patched firmware on my JIOFI 3 which was running the version "JMR 540 - FXN_JMR540_R6.10"
- I have Flash both - system and recoveryfs
I am able to use other sim card in this (Thanks alot for this)
My major concern is that:
Will my device gets auto-updated (which will lock the bootloader)?
Should I continue using it or stop, will it get autoupdate even on latest unlocked patched firmware?
 

Top Liked Posts

  • There are no posts matching your filters.
  • 1
    Sad soul here. I am one of those unfortunate people whose JioFi got updated on very first day when jio pushed new update and locked bootloader. After checking for several weeks for any chance of revival I reached out to @abhimortal6 and he was welcoming and kind. This was his reply then -

    "Hi, it can be unlocked but there is no easy way to do it, it basically requires shorting JioFi into unsecure EDL and re-flashing old bootloader"

    He also mentioned that he is busy right now to focus on this device may be in future he will find a simple way and make guide out of it.
    But right now there is nothing a generic or advance user can do and due to shortage of self taught devs.
    I am hopeful we'll see another unlock 🤞
    1
    works great!

    few issues i faced and managed to fix 👇

    1. "fastboot devices" not showing anything
    what fixed it: make sure you have installed the adb driver (which contains the generic google android usb driver) linked in the first post. then with the jiofi connected, go to device manager and find something similar to "android device" "unknown usb" etc with a yellow warning icon. right click and click update driver, manually select the google usb driver and jiofi will now show up in command line.

    2. even with successful flashing the dashboard didn't show the "this is a hacked firmware..." message at the top meaning that somehow the flash didn't work"
    what fixed it: as mentioned in the FAQ, you have do both "fastboot flash system" and "fastboot flash recoveryfs" with the same hacked system.img

    rest went smoothly :)
  • 45
    Unlocked Firmware for JioFi 3 JMR540 & JMR541

    Disclaimer
    I am not responsible for any kind of damage to your device.
    Use this firmware at your own risk
    Post is for educational purpose only.


    ONLY FOR JMR 540 & JMR 541


    I was able to dump and reverse engineer JioFi 3's firmware to see if I can unlock the SIM restrictions. JioFi 3 is designed by Foxconn it uses generic firmware. Unlocking took time though. Tested with Vi, Airtel.

    UPDATE 17-10-21: Jio pushed a firmware update which is locking boot loader. If your device is not updated yet it is advised to re-flash your firmware with patched image given below which basically disables auto updates. If you're already locked out, currently there's no easy fix for that.

    If you haven't used your device from a long time or you're still on lower or equal version than below it is advised not to use JioFi with SIM, flash this firmware first if you want to test SIM unlock.




    Guide

    Make sure you're on same or lower firmware version
    • JMR 540 - FXN_JMR540_R6.16
    • JMR 541 - FXN_JMR541_R3.10



    1. Locate your device model and download the respective Firmware and extract it to a known location

    2. Install drivers and tools (skip if already installed)

    • Install Fastboot drivers ( google it for mac and linux it's easy to find)
    • Install Fastboot ( google it for mac and linux it's easy to find)

    3. Prepare device

    • Remove battery from JioFi 3
    • Locate reset pin hole button
    • Lay down JioFi 3
    • Use Paper Clip / SIM Ejector Tool to press button inside (using sharp object is not recommended)
    • Keep pressing button down and insert USB cable
    • Release button as soon as all the LEDs in Display turns RED. This means device is in boot loader mode

    4. Flashing Unlocked Firmware

    • Open adb and fastboot tools terminal
    • Enter following to check if device is connected

    • fastboot devices

    • It will return something like this
    • baxxxxx fastboot

    • This means device is connected. If your device doesn't show up here please check drivers in Device manager
    • Now first erase the system partition

    • fastboot erase system

    • It will return something like this
    • erasing 'system'... OKAY [ 1.104s] finished. total time: 1.105s

    • Now flash the firmware
    • fastboot flash system "D:\system.img" ( replace path )

    • It should return something like this
    • sending 'system' (34306 KB)... OKAY [ 1.276s] writing 'system'... OKAY [ 9.462s] finished. total time: 10.741s

    • Now send reboot command to device
    • fastboot reboot

    • You'll notice device will reboot normally now you can unplug the cable.

    Congratulations your device is now unlocked and you can reinsert battery and another SIM for testing.

    Firmware will take long time than usual to boot do not panic.

    4. Changing APN
    • Insert SIM connect with JioFi 3 wait it to intialize
    • Open Web UI from browser (http://jiofi.local.html/)
    • Now login (default username/pwd is administrator/administrator)
    • In Network Tab you'll find setting for changing APN
    • Put it on manual and enter "internet" as APN (without quotes)
    • Hit apply/save device will reboot again automatically and it'll auto connect
    • Just wait patience is the key here it'll connect.

    If something goes WRONG or you want to UNDO you can re flash original firmware which is provided in this post.


    Original backup




    FAQs

    1. Q. My device is not visible in fastboot devices
      A. Confirm driver installation a faulty cable can also be the issue.
      .
    2. Q. Everything went well but still no changes in dashboard
      A. After successful flash if you still don't see the changes your device is probably booting from recovery partition. Try flashing recovery partition by
      fastboot erase recoveryfs
      fastboot flash recoveryfs "D:\system.img"
      .


    3. Q. After resetting device from pin hole button it shows INVALID SIM.
      A. This is supposed to happen just reboot the device it'll work again.
      .
    4. Q. Can I undo all this and get back to original firmware
      A. Yes just flash the original firmware provided in post and reset the device.
      .
    5. Q. I 'accidentally' flashed my recovery and boot partition
      A. Well accidentally I've backed up recovery and boot download from below

      1.
      JMR540_boot_recovery.rar
      2. JMR541_boot_recovery.rar
      .
    6. Q. FAILED: (remote: Image is locked) issue while erasing/flashing image
      A. Jio recently pushed an firmware update which re-locks simlock and bootloader which basically means you can't flash unsigned/custom firmware. Currently there is no fix.







    Mentions:
    Thanks to
    Karuppusamy for testing it on JMR541.


    What about JioFi 2, 4, 5, 6?
    Reverse Engineering takes lot of time and coffee. Until I get physical access to device I won't be able to unlock it. I'm constantly searching them on OLX as soon as I get hands on I'll surely try to RE and unlock it. I'll update the same here if there is no update here at the time of your reading then I haven't got the device yet so please don't spam for update hope you understand that I don't get anything by doing these things, I do it for liberation of locked hardware to meet it's real destiny and of course for the people. I also have a day job so no I cannot guide or teach you, hope you understand why.



    5
    bro is unlocking more 4g bands or manual selection of bands can be done ?
    Totally possible even 3G but it can't be done through WebUI it'll requires shell access.
    3
    successfully unlocked my jiofi 3 JMR541. tested with voda and its working well and good. Thanks a ton for this bro.
    I was late in checking this thread and got shipped airtel unlocked mifi from home.
    Can you show us dashboard screenshot. This will help other users to verify
    3
    after knowing from u guys about recent update pushed by jio my device wasn't updated so i instantly removed the sim and waiting for update from abhi
    For Jio --- guys u have stopped selling this or selling in 5k -6k like black marketing and nor your devices are built well, if someone has unlocked it what's the problem you have not pushed any update to other models which were previously unlocked now those devices are being sold at higher prices. I am happy that airtel and vi are here otherwise your greediness to capture everything would have led us to ______ no words to describe'
    You can install and test patched firmware auto updates are patched and disabled now, link is in original post. Devices which are already updated, there is no easy fix for them right now. Jio loves their users aww ( throws JioFi in space ).