• Introducing XDA Computing: Discussion zones for Hardware, Software, and more!    Check it out!

Hard Bricked Zenfone Unbrick (Last method to try)

Search This thread

rishav754

Senior Member
Jul 25, 2013
83
19
28
New Delhi
" Creator of this method @shakalaca (Shaka Huang) "







Its advisable to try this method after trying all other methods you found . (The last method)

Advice : If your phone is still under warranty please visit service centre . This method may result into dead phone .

Applicable devices : zenfone 4,zenfone 5, zenfone 6 ( CG versions)

Condition for applicability : Only usb logo is showing and user is unable to enter into fastboot/bootloader

First check : press power + volume up button to power on the phone and release(only) power button at time asus logo start showing( still pressing the volume up button )

If you are able to enter into fastboot then this process is not applicable for your case. please don't use this method.

In case after applying first check you are unable to enter fastboot :
check these:
  • Battery is charged or not
  • Are you pressing right button ??
  • Recheck the time to release power button

Still not able to enter into fast boot then apply the below method for entering into droidboot/fastboot .
conclusion: your droidboot got corrupted .



Requirements : Windows 7 pc/laptop (drivers tested on this devices)

SECTION 1

Drivers Required : 1. iSocUSB-Driver-Setup-1.0.4.exe
2. xfstk-downloader-setup-1.5.1.exe

instruction : install above driver as per ranking. follow these instruction while installing:
1. Right click on setup
2. Select run as administrator
Note : while installing isoc drive system may ask you to connect your device or restart your device. Don't skip
those steps or it will result into driver not working case. Please allow all things asked by your pc .

Driver Checkpoint: 1. connect your device
2. Wait for windows to install driver automatic . Below picture will pop up

3. Right click on my computer , select "properties ". Go to "device manager". select "intel
soc"
3. when your phone is turned on a USB patterns and connected to the computer there
should be two new devices, are classified under Intel Soc: CloverviewPlus Device and
Intel Soc USB Driver . Picture :

If both are not showing in soc section try restating your computer . Check again still no improvement then :

Driver Required : IntelAndroidDrvSetup1.5.0.exe

install above driver as per "instruction "

Necessary Condition for working of tool : Driver Checkpoint condition must be met


SECTION 2
Step 1.1 Download folder as per your model given : zenfone 4 / zenfone 5 / zenfone 6
Check Folder contains these files : dnx.bin , ifwi.bin , dnx_osr.bin , fastboot-2.19.img.pos.bin
Put all files into single folder .

Step 1.2
Confirm the phone has been connected to the computer, which also appeared Device Manager device described above,open xFSTK DOWNLOADER
After opening note beneath the tabs to switch to the rearmost CLVP A0 / B0 / B1




Confirm the Device status field which shows Scanning: CLOVERVIEWPLUS TARGETS DETECTED: 1, if the last place is displayed as 0, make sure that the Device Manager inside It has detected devices.



Step 1.3:
Give proper path to corresponding section :

Fw Dnx : dnx.bin
IFWI : ifwi.bin
OS dnx : dnx_osr.bin
OS image : fastboot.xx.imp.pos.bin


Then press begin download


After the completion of the phone will automatically reboot if the boot screen becomes Intel inside patterns means you have reached your destination .
Now you can enter into fastboot/booloader/drodboot.There are so many methods given to unbrick, soft bricked phone

Advice: USe Adb method to recover your phone.

Problems detected :

Encountering " Windriver Error: 0x20000015 "

Expected cause : Driver not installed correctly .

Method :
1. uninstall xfstk downloader
2.restart computer
3. right click on xfstk downloader and select option run as administrator .
4. install first then open xftsk as admistrator
5. give path to those files on xftsk as per instruction
6. Press the Start Download button in XFSTK
7. Then connect usb and press power + volume up button .
Still encountering :

Method :
1. open Device Manager (from Windows command prompt, type devmgmt.msc)
2. Find the device (it probably is under Android Devices.)
3. RIght click on the device, choose "Update Driver" and then "Browse My Computer..." and then "Let me
pick from a list of device drivers on my computer."
4. You might have to unclick "Show Compatible Hardware"
5. In the Manufacturer section, pick Google or Intel.
6. Under Model, pick "Android Bootloader Interface."
7. Click Next, and then Ok to Ignore scary warnings.
8. Start xftsk download-er do the required thing

If above links are dead then please go to : http://www.mediafire.com/folder/7qapfy4zqvxf6#z3i6bncz0beih

For more knowledge visit : https://github.com/shakalaca/ZenFone-boot-tools

Sorry for my bad English .

Thnaks :D
Rishav754
 
Last edited:

rishav754

Senior Member
Jul 25, 2013
83
19
28
New Delhi
If you are still getting error "Windriver Error: 0x20000015 " try this :
1. set a live ubuntu Linux on usb. http://www.instructables.com/id/How-to-make-your-own-Ubuntu-LiveUSB/
2. install xfstk driver . https://communities.intel.com/thread/57018
3. start from section 2
Read before starting , Comment by @marionette
1. Started and did everything on the original post, encountered Windriver Error: 0x20000015. I tried both method but it didn't work, to the point that I build xfstk in linux only to find it still throws errors.
What fixed it for me was to hold down the volume down button before I connect the cable to my laptop for whatever reason but it worked.

2. It then still gave me an error but I forgot what it was, I didn't save the logs until much later. Scouring the thread someone suggests providing a soft fuse file. Okay. I downloaded the file from him BUT xfstk gives me error code 45 softfuses signature error. I had to download the raw firmware from here to get the soft fuse file to get it to work.

https://andrewbenedictus.wordpress.com/2016/02/15/how-to-unbrick-asus-zenfone-5-stuck-on-intel-logo/

THIS FORUM IS DEAD , KINDLY USE OTHER METHODS
THANK YOU
 
Last edited:

LuBu161

Member
Aug 23, 2015
22
2
  • Like
Reactions: maxibi

mcpterra

Senior Member
Aug 4, 2009
141
12
Hello, good evening.
I tried in a Zenfone 6 but it fails.
Saying: softfuse missing, please insert softfuse..... and then softfuses signature error code 45

Please can you help me ?

Best regads

---------- Post added at 04:58 AM ---------- Previous post was at 04:53 AM ----------

That is the error.....
Can you help me?
04:54:49 - XFSTK-STATUS--USBSN:39FD7A5E068590C4--Softfuses Binary absent. Please provide binary.
04:54:49 - XFSTK-LOG--USBSN:39FD7A5E068590C4--GetOpCode
04:54:49 - XFSTK-LOG--USBSN:39FD7A5E068590C4--ReadInAck
04:54:49 - XFSTK-LOG--USBSN:39FD7A5E068590C4--GetAck
04:54:49 - XFSTK-LOG--USBSN:39FD7A5E068590C4--GetAck - HLT0(0x4)
04:54:49 - XFSTK-LOG--USBSN:39FD7A5E068590C4--Softfuse Binary file size = 0 or Number of keys = 0
04:54:49 - XFSTK-LOG--USBSN:39FD7A5E068590C4--void CloverviewPlusDownloader::do_abort()
04:54:49 - XFSTK-LOG--USBSN:39FD7A5E068590C4--Abort
04:54:49 - XFSTK-STATUS--USBSN:39FD7A5E068590C4--FAIL
04:54:49 - XFSTK-STATUS--USBSN:39FD7A5E068590C4--Errors encounter during FW download. Aborting ...
04:54:49 - XFSTK-LOG--USBSN:39FD7A5E068590C4--virtual bool CloverviewPlusDownloader::GetStatus()
 
  • Like
Reactions: maxibi

Amfakh

Senior Member
Aug 7, 2015
80
20
Jakarta
it's always says WinDriver Error although I've tried all of the method

xfstklog_Rab_30._Des_14-50-30_2015.txt
14:50:05 - XFSTK Downloader API 1.5.1 Copyright (c) 2013 Intel Corporation
14:50:05 - fwdnx -- C:/Program Files/xFSTK/dnx.bin
14:50:05 - fwimage -- C:/Program Files/xFSTK/ifwi.bin
14:50:05 - osdnx -- C:/Program Files/xFSTK/dnx_osr.bin
14:50:05 - osimage -- C:/Program Files/xFSTK/fastboot-2.19.img.pos.bin
14:50:05 - gpflags -- 0x80000001
14:50:05 - XFSTK-LOG--USBSN:--virtual bool CloverviewPlusDownloader::SetDevice(IGenericDevice*)
14:50:05 - Initiating download...
14:50:05 - XFSTK-LOG--USBSN:--virtual bool CloverviewPlusDownloader::UpdateTarget()
14:50:05 - XFSTK-LOG--USBSN:--FWDnxPath -- C:/Program Files/xFSTK/dnx.bin
14:50:05 - XFSTK-LOG--USBSN:--FWImagePath -- C:/Program Files/xFSTK/ifwi.bin
14:50:05 - XFSTK-LOG--USBSN:--SoftfusesPath -- BLANK.bin
14:50:05 - XFSTK-LOG--USBSN:--OSDnxPath -- C:/Program Files/xFSTK/dnx_osr.bin
14:50:05 - XFSTK-LOG--USBSN:--OSImagePath -- C:/Program Files/xFSTK/fastboot-2.19.img.pos.bin
14:50:05 - XFSTK-LOG--USBSN:--MiscDnxPath --
14:50:05 - XFSTK-LOG--USBSN:--Gpflags -- 80000001
14:50:05 - XFSTK-LOG--USBSN:--DebugLevel -- ffffffff
14:50:05 - XFSTK-LOG--USBSN:--UsbDelay ms -- 0
14:50:05 - XFSTK-LOG--USBSN:--TransferType -- USB
14:50:05 - XFSTK-LOG--USBSN:--WipeIFWI -- False
14:50:05 - XFSTK-LOG--USBSN:--Idrq -- False
14:50:05 - XFSTK-LOG--USBSN:--Verbose -- True
14:50:05 - XFSTK-LOG--USBSN:--void CloverviewPlusDownloader::Init()
14:50:05 - XFSTK-LOG--USBSN:--Open
14:50:05 - XFSTK-LOG--USBSN:--void CloverviewPlusUtils::SetUsbsn(char*)
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--USB Device found - USBSN: 6EA4664842C82EE4 Address:2
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--void CloverviewPlusDownloader::do_update(CloverviewPlusOptions*)
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--Start
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--Sending DnER...
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--WriteOutPipe DnER
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--WriteOutPipe 0
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--Write --->DnER
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--GetOpCode
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--ReadInAck
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--GetAck
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--GetAck - DORM(0x4)
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--OS: Handle OS download...
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--GetOpCode
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--Changing to DLDR_STATE_OS_NORMAL ...
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--CheckFile
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--CheckFile
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--_num OS Images : 1
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--_temp_data : 67a9
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--OSII: 0 Data Size: 13586944
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--_Temp Data is: 67a9 h
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--InitOsipHdr
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--Init OSIP header ...
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--_After fread osip_hdr
14:50:05 - XFSTK-STATUS--USBSN:6EA4664842C82EE4--POS download is in progress ...
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--StartOs
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--sending 6 DWORDS of DnxOS size and checksum...
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--GetOsDnXHdr
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--C:/Program Files/xFSTK/dnx_osr.bin size:99296 bytes
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--WriteOutPipe a?
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--WriteOutPipe 0
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--Write --->a?
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--End of StHandleOsNormal
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--GetOpCode
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--ReadInAck
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--GetAck
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--GetAck - DXBL(0x4)
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--OS: Sending DnX ...
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--OsDXBL
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--GetOsDnX
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--C:/Program Files/xFSTK/dnx_osr.bin size:99296 bytes
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--WriteOutPipe __BINARY__
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--WriteOutPipe 0
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--Write --->__BINARY__
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--LogProgress
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--GetOpCode
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--ReadInAck
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--GetAck
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--GetAck - ROSIP$$$(0x8)
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--GetOsipHdr
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--Get OSIP header + Partion Table...
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--sending OSIP...
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--sending OSIP header + Partion Table...
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--WriteOutPipe __BINARY__
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--WriteOutPipe 0
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--Write --->__BINARY__
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--GetOpCode
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--ReadInAck
14:50:05 - XFSTK-LOG--USBSN:6EA4664842C82EE4--GetAck
14:50:10 - XFSTK-LOG--USBSN:6EA4664842C82EE4--usb_bulk_read() fails
14:50:10 - XFSTK-LOG--USBSN:6EA4664842C82EE4--Windriver Error: 0x20000015, Timeout expired
14:50:15 - XFSTK-LOG--USBSN:6EA4664842C82EE4--usb_bulk_read() fails
14:50:15 - XFSTK-LOG--USBSN:6EA4664842C82EE4--Windriver Error: 0x20000015, Timeout expired
14:50:20 - XFSTK-LOG--USBSN:6EA4664842C82EE4--usb_bulk_read() fails
14:50:20 - XFSTK-LOG--USBSN:6EA4664842C82EE4--Windriver Error: 0x20000015, Timeout expired
14:50:25 - XFSTK-LOG--USBSN:6EA4664842C82EE4--usb_bulk_read() fails
14:50:25 - XFSTK-LOG--USBSN:6EA4664842C82EE4--Windriver Error: 0x20000015, Timeout expired
14:50:30 - XFSTK-LOG--USBSN:6EA4664842C82EE4--usb_bulk_read() fails
14:50:30 - XFSTK-LOG--USBSN:6EA4664842C82EE4--Windriver Error: 0x20000015, Timeout expired
14:50:30 - XFSTK-LOG--USBSN:6EA4664842C82EE4--Device is not responding...
14:50:30 - XFSTK-LOG--USBSN:6EA4664842C82EE4--GetAck - (0xBAADF00D)
14:50:30 - XFSTK-STATUS--USBSN:6EA4664842C82EE4--Unknown Ack code:baadf00d, aborting ...
14:50:30 - XFSTK-LOG--USBSN:6EA4664842C82EE4--void CloverviewPlusDownloader::do_abort()
14:50:30 - XFSTK-LOG--USBSN:6EA4664842C82EE4--Abort
14:50:30 - XFSTK-STATUS--USBSN:6EA4664842C82EE4--FAIL
14:50:30 - XFSTK-STATUS--USBSN:6EA4664842C82EE4--Errors encounter during OS download. Aborting ...
 

zakwanPHG

Senior Member
Mar 6, 2015
346
161
" Creator of this method @shakalaca (Shaka Huang) "







Its advisable to try this method after trying all other methods you found . (The last method)

Advice : If your phone is still under warranty please visit service centre . This method may result into dead phone .

Applicable devices : zenfone 4,zenfone 5, zenfone 6 ( CG versions)

Condition for applicability : Only usb logo is showing and user is unable to enter into fastboot/bootloader

First check : press power + volume up button to power on the phone and release(only) power button at time asus logo start showing( still pressing the volume up button )

If you are able to enter into fastboot then this process is not applicable for your case. please don't use this method.

In case after applying first check you are unable to enter fastboot :
check these:
  • Battery is charged or not
  • Are you pressing right button ??
  • Recheck the time to release power button

Still not able to enter into fast boot then apply the below method for entering into droidboot/fastboot .
conclusion: your droidboot got corrupted .



Requirements : Windows 7 pc/laptop (drivers tested on this devices)

SECTION 1

Drivers Required : 1. iSocUSB-Driver-Setup-1.0.4.exe
2. xfstk-downloader-setup-1.5.1.exe

instruction : install above driver as per ranking. follow these instruction while installing:
1. Right click on setup
2. Select run as administrator
Note : while installing isoc drive system may ask you to connect your device or restart your device. Don't skip
those steps or it will result into driver not working case. Please allow all things asked by your pc .

Driver Checkpoint: 1. connect your device
2. Wait for windows to install driver automatic . Below picture will pop up

3. Right click on my computer , select "properties ". Go to "device manager". select "intel
soc"
3. when your phone is turned on a USB patterns and connected to the computer there
should be two new devices, are classified under Intel Soc: CloverviewPlus Device and
Intel Soc USB Driver . Picture :

If both are not showing in soc section try restating your computer . Check again still no improvement then :

Driver Required : IntelAndroidDrvSetup1.5.0.exe

install above driver as per "instruction "

Necessary Condition for working of tool : Driver Checkpoint condition must be met


SECTION 2
Step 1.1 Download folder as per your model given : zenfone 4 / zenfone 5 / zenfone 6
Check Folder contains these files : dnx.bin , ifwi.bin , dnx_osr.bin , fastboot-2.19.img.pos.bin
Put all files into single folder .

Step 1.2
Confirm the phone has been connected to the computer, which also appeared Device Manager device described above,open xFSTK DOWNLOADER
After opening note beneath the tabs to switch to the rearmost CLVP A0 / B0 / B1




Confirm the Device status field which shows Scanning: CLOVERVIEWPLUS TARGETS DETECTED: 1, if the last place is displayed as 0, make sure that the Device Manager inside It has detected devices.



Step 1.3:
Give proper path to corresponding section :

Fw Dnx : dnx.bin
IFWI : ifwi.bin
OS dnx : dnx_osr.bin
OS image : fastboot.xx.imp.pos.bin


Then press begin download


After the completion of the phone will automatically reboot if the boot screen becomes Intel inside patterns means you have reached your destination .
Now you can enter into fastboot/booloader/drodboot.There are so many methods given to unbrick, soft bricked phone

Advice: USe Adb method to recover your phone.

Problems detected :

Encountering " Windriver Error: 0x20000015 "

Expected cause : Driver not installed correctly .

Method :
1. uninstall xfstk downloader
2.restart computer
3. right click on xfstk downloader and select option run as administrator .
4. install first then open xftsk as admistrator
5. give path to those files on xftsk as per instruction
6. Press the Start Download button in XFSTK
7. Then connect usb and press power + volume up button .
Still encountering :

Method :
1. open Device Manager (from Windows command prompt, type devmgmt.msc)
2. Find the device (it probably is under Android Devices.)
3. RIght click on the device, choose "Update Driver" and then "Browse My Computer..." and then "Let me
pick from a list of device drivers on my computer."
4. You might have to unclick "Show Compatible Hardware"
5. In the Manufacturer section, pick Google or Intel.
6. Under Model, pick "Android Bootloader Interface."
7. Click Next, and then Ok to Ignore scary warnings.
8. Start xftsk download-er do the required thing

If above links are dead then please go to : http://www.mediafire.com/folder/7qapfy4zqvxf6#z3i6bncz0beih

For more knowledge visit : https://github.com/shakalaca/ZenFone-boot-tools

Sorry for my bad English .

Thnaks :D
Rishav754

Hi,i just successful get my fastboot..my problem now is,i cant adb sideload firmware.. In recovery log said E:cant mount data and installation aborted

---------- Post added at 02:48 PM ---------- Previous post was at 02:28 PM ----------

" Creator of this method @shakalaca (Shaka Huang) "







Its advisable to try this method after trying all other methods you found . (The last method)

Advice : If your phone is still under warranty please visit service centre . This method may result into dead phone .

Applicable devices : zenfone 4,zenfone 5, zenfone 6 ( CG versions)

Condition for applicability : Only usb logo is showing and user is unable to enter into fastboot/bootloader

First check : press power + volume up button to power on the phone and release(only) power button at time asus logo start showing( still pressing the volume up button )

If you are able to enter into fastboot then this process is not applicable for your case. please don't use this method.

In case after applying first check you are unable to enter fastboot :
check these:
  • Battery is charged or not
  • Are you pressing right button ??
  • Recheck the time to release power button

Still not able to enter into fast boot then apply the below method for entering into droidboot/fastboot .
conclusion: your droidboot got corrupted .



Requirements : Windows 7 pc/laptop (drivers tested on this devices)

SECTION 1

Drivers Required : 1. iSocUSB-Driver-Setup-1.0.4.exe
2. xfstk-downloader-setup-1.5.1.exe

instruction : install above driver as per ranking. follow these instruction while installing:
1. Right click on setup
2. Select run as administrator
Note : while installing isoc drive system may ask you to connect your device or restart your device. Don't skip
those steps or it will result into driver not working case. Please allow all things asked by your pc .

Driver Checkpoint: 1. connect your device
2. Wait for windows to install driver automatic . Below picture will pop up

3. Right click on my computer , select "properties ". Go to "device manager". select "intel
soc"
3. when your phone is turned on a USB patterns and connected to the computer there
should be two new devices, are classified under Intel Soc: CloverviewPlus Device and
Intel Soc USB Driver . Picture :

If both are not showing in soc section try restating your computer . Check again still no improvement then :

Driver Required : IntelAndroidDrvSetup1.5.0.exe

install above driver as per "instruction "

Necessary Condition for working of tool : Driver Checkpoint condition must be met


SECTION 2
Step 1.1 Download folder as per your model given : zenfone 4 / zenfone 5 / zenfone 6
Check Folder contains these files : dnx.bin , ifwi.bin , dnx_osr.bin , fastboot-2.19.img.pos.bin
Put all files into single folder .

Step 1.2
Confirm the phone has been connected to the computer, which also appeared Device Manager device described above,open xFSTK DOWNLOADER
After opening note beneath the tabs to switch to the rearmost CLVP A0 / B0 / B1




Confirm the Device status field which shows Scanning: CLOVERVIEWPLUS TARGETS DETECTED: 1, if the last place is displayed as 0, make sure that the Device Manager inside It has detected devices.



Step 1.3:
Give proper path to corresponding section :

Fw Dnx : dnx.bin
IFWI : ifwi.bin
OS dnx : dnx_osr.bin
OS image : fastboot.xx.imp.pos.bin


Then press begin download


After the completion of the phone will automatically reboot if the boot screen becomes Intel inside patterns means you have reached your destination .
Now you can enter into fastboot/booloader/drodboot.There are so many methods given to unbrick, soft bricked phone

Advice: USe Adb method to recover your phone.

Problems detected :

Encountering " Windriver Error: 0x20000015 "

Expected cause : Driver not installed correctly .

Method :
1. uninstall xfstk downloader
2.restart computer
3. right click on xfstk downloader and select option run as administrator .
4. install first then open xftsk as admistrator
5. give path to those files on xftsk as per instruction
6. Press the Start Download button in XFSTK
7. Then connect usb and press power + volume up button .
Still encountering :

Method :
1. open Device Manager (from Windows command prompt, type devmgmt.msc)
2. Find the device (it probably is under Android Devices.)
3. RIght click on the device, choose "Update Driver" and then "Browse My Computer..." and then "Let me
pick from a list of device drivers on my computer."
4. You might have to unclick "Show Compatible Hardware"
5. In the Manufacturer section, pick Google or Intel.
6. Under Model, pick "Android Bootloader Interface."
7. Click Next, and then Ok to Ignore scary warnings.
8. Start xftsk download-er do the required thing

If above links are dead then please go to : http://www.mediafire.com/folder/7qapfy4zqvxf6#z3i6bncz0beih

For more knowledge visit : https://github.com/shakalaca/ZenFone-boot-tools

Sorry for my bad English .

Thnaks :D
Rishav754

Hi,i just successful get my fastboot..my problem now is,i cant adb sideload firmware.. In recovery log said E:cant mount data and installation aborted
 

Rikkuzen193

Member
Apr 3, 2015
39
2
Hello, I have a dead phone but still is detected by pc, however I can't get into the driver checkpoint, only the Intel Soc Device is detected and no CloverViewPlus device, I tried restarting and installing the driver but still nothing, could you guide me?
 
  • Like
Reactions: maxibi

arnab1992

Senior Member
Aug 5, 2015
68
18
Hi,i just successful get my fastboot..my problem now is,i cant adb sideload firmware.. In recovery log said E:cant mount data and installation aborted

---------- Post added at 02:48 PM ---------- Previous post was at 02:28 PM ----------



Hi,i just successful get my fastboot..my problem now is,i cant adb sideload firmware.. In recovery log said E:cant mount data and installation aborted

flash twrp via fastboot and then flash rom
 
  • Like
Reactions: maxibi

junior kaniucki

New member
Oct 27, 2014
1
2
I can not solve the problem soon usb zenfone 5 model T00J

:confused:
I tried to resolve this problem as soon usb, already went on several tutorials and always error 0x0000015 but my drivers station tds functioning normally wanted a 'm helps long without smartphone if you can provide me with a method I q with a live linux usb to the right but not know how to use linux wanted a help please . sorry for my English but I am Brazilian I do not know English fluently
 
  • Like
Reactions: maxibi and smnshuvo

anakmanja6th

New member
Jan 28, 2015
1
0
Errors encounter during download

hi, i have problem when press begin download

12:32:42 - XFSTK-LOG--USBSN:2FCEC0CDDFEAEDB2--Windriver Error: 0x20000015, Timeout expired
12:32:42 - XFSTK-LOG--USBSN:2FCEC0CDDFEAEDB2--LogError
12:32:42 - XFSTK-STATUS--USBSN:2FCEC0CDDFEAEDB2--Error Code: 1 - Connection error
12:32:42 - XFSTK-STATUS--USBSN:2FCEC0CDDFEAEDB2--Failed to start Dldr state machine, aborting ...
12:32:42 - XFSTK-LOG--USBSN:2FCEC0CDDFEAEDB2--void CloverviewPlusDownloader::do_abort()
12:32:42 - XFSTK-LOG--USBSN:2FCEC0CDDFEAEDB2--Abort
12:32:42 - XFSTK-STATUS--USBSN:2FCEC0CDDFEAEDB2--FAIL
12:32:42 - XFSTK-STATUS--USBSN:2FCEC0CDDFEAEDB2--Errors encounter during download. Aborting...
12:32:52 - XFSTK-STATUS--Reconnecting to device - Attempt #20

I have tried following the instructions, but always have same problem, please hel me :) thanks!
 

Attachments

  • Untitled.jpg
    Untitled.jpg
    68 KB · Views: 935

ffiieerryylll

New member
Feb 10, 2016
1
0
Z380KL unbrick

Z380KL P024 zenpad 8 unbricking method as a LAST RESORT:

drive.google.com/file/d/0BzjHJbuYb9NWenVfLVZWempaaWM/view?usp=sharing
 
Last edited:

zakwanPHG

Senior Member
Mar 6, 2015
346
161
flash twrp via fastboot and then flash rom

u know what..i also flash recovery img,and the result same.failed to adbsideload firmware..finally i found last step tutorial[not include in this thread]in shaka huang pages is wipe partition after done using fstk tool.and then flash back my droitboot/recovery img kk version.
 

Top Liked Posts

  • There are no posts matching your filters.
  • 9
    " Creator of this method @shakalaca (Shaka Huang) "







    Its advisable to try this method after trying all other methods you found . (The last method)

    Advice : If your phone is still under warranty please visit service centre . This method may result into dead phone .

    Applicable devices : zenfone 4,zenfone 5, zenfone 6 ( CG versions)

    Condition for applicability : Only usb logo is showing and user is unable to enter into fastboot/bootloader

    First check : press power + volume up button to power on the phone and release(only) power button at time asus logo start showing( still pressing the volume up button )

    If you are able to enter into fastboot then this process is not applicable for your case. please don't use this method.

    In case after applying first check you are unable to enter fastboot :
    check these:
    • Battery is charged or not
    • Are you pressing right button ??
    • Recheck the time to release power button

    Still not able to enter into fast boot then apply the below method for entering into droidboot/fastboot .
    conclusion: your droidboot got corrupted .



    Requirements : Windows 7 pc/laptop (drivers tested on this devices)

    SECTION 1

    Drivers Required : 1. iSocUSB-Driver-Setup-1.0.4.exe
    2. xfstk-downloader-setup-1.5.1.exe

    instruction : install above driver as per ranking. follow these instruction while installing:
    1. Right click on setup
    2. Select run as administrator
    Note : while installing isoc drive system may ask you to connect your device or restart your device. Don't skip
    those steps or it will result into driver not working case. Please allow all things asked by your pc .

    Driver Checkpoint: 1. connect your device
    2. Wait for windows to install driver automatic . Below picture will pop up

    3. Right click on my computer , select "properties ". Go to "device manager". select "intel
    soc"
    3. when your phone is turned on a USB patterns and connected to the computer there
    should be two new devices, are classified under Intel Soc: CloverviewPlus Device and
    Intel Soc USB Driver . Picture :

    If both are not showing in soc section try restating your computer . Check again still no improvement then :

    Driver Required : IntelAndroidDrvSetup1.5.0.exe

    install above driver as per "instruction "

    Necessary Condition for working of tool : Driver Checkpoint condition must be met


    SECTION 2
    Step 1.1 Download folder as per your model given : zenfone 4 / zenfone 5 / zenfone 6
    Check Folder contains these files : dnx.bin , ifwi.bin , dnx_osr.bin , fastboot-2.19.img.pos.bin
    Put all files into single folder .

    Step 1.2
    Confirm the phone has been connected to the computer, which also appeared Device Manager device described above,open xFSTK DOWNLOADER
    After opening note beneath the tabs to switch to the rearmost CLVP A0 / B0 / B1




    Confirm the Device status field which shows Scanning: CLOVERVIEWPLUS TARGETS DETECTED: 1, if the last place is displayed as 0, make sure that the Device Manager inside It has detected devices.



    Step 1.3:
    Give proper path to corresponding section :

    Fw Dnx : dnx.bin
    IFWI : ifwi.bin
    OS dnx : dnx_osr.bin
    OS image : fastboot.xx.imp.pos.bin


    Then press begin download


    After the completion of the phone will automatically reboot if the boot screen becomes Intel inside patterns means you have reached your destination .
    Now you can enter into fastboot/booloader/drodboot.There are so many methods given to unbrick, soft bricked phone

    Advice: USe Adb method to recover your phone.

    Problems detected :

    Encountering " Windriver Error: 0x20000015 "

    Expected cause : Driver not installed correctly .

    Method :
    1. uninstall xfstk downloader
    2.restart computer
    3. right click on xfstk downloader and select option run as administrator .
    4. install first then open xftsk as admistrator
    5. give path to those files on xftsk as per instruction
    6. Press the Start Download button in XFSTK
    7. Then connect usb and press power + volume up button .
    Still encountering :

    Method :
    1. open Device Manager (from Windows command prompt, type devmgmt.msc)
    2. Find the device (it probably is under Android Devices.)
    3. RIght click on the device, choose "Update Driver" and then "Browse My Computer..." and then "Let me
    pick from a list of device drivers on my computer."
    4. You might have to unclick "Show Compatible Hardware"
    5. In the Manufacturer section, pick Google or Intel.
    6. Under Model, pick "Android Bootloader Interface."
    7. Click Next, and then Ok to Ignore scary warnings.
    8. Start xftsk download-er do the required thing

    If above links are dead then please go to : http://www.mediafire.com/folder/7qapfy4zqvxf6#z3i6bncz0beih

    For more knowledge visit : https://github.com/shakalaca/ZenFone-boot-tools

    Sorry for my bad English .

    Thnaks :D
    Rishav754
    2
    If you are still getting error "Windriver Error: 0x20000015 " try this :
    1. set a live ubuntu Linux on usb. http://www.instructables.com/id/How-to-make-your-own-Ubuntu-LiveUSB/
    2. install xfstk driver . https://communities.intel.com/thread/57018
    3. start from section 2
    Read before starting , Comment by @marionette
    1. Started and did everything on the original post, encountered Windriver Error: 0x20000015. I tried both method but it didn't work, to the point that I build xfstk in linux only to find it still throws errors.
    What fixed it for me was to hold down the volume down button before I connect the cable to my laptop for whatever reason but it worked.

    2. It then still gave me an error but I forgot what it was, I didn't save the logs until much later. Scouring the thread someone suggests providing a soft fuse file. Okay. I downloaded the file from him BUT xfstk gives me error code 45 softfuses signature error. I had to download the raw firmware from here to get the soft fuse file to get it to work.

    https://andrewbenedictus.wordpress.com/2016/02/15/how-to-unbrick-asus-zenfone-5-stuck-on-intel-logo/

    THIS FORUM IS DEAD , KINDLY USE OTHER METHODS
    THANK YOU
    2
    My asus zenfone 5 does not detecting in pc what to do
    2
    I can not solve the problem soon usb zenfone 5 model T00J

    :confused:
    I tried to resolve this problem as soon usb, already went on several tutorials and always error 0x0000015 but my drivers station tds functioning normally wanted a 'm helps long without smartphone if you can provide me with a method I q with a live linux usb to the right but not know how to use linux wanted a help please . sorry for my English but I am Brazilian I do not know English fluently
    1
    " Creator of this method @shakalaca (Shaka Huang) "







    Its advisable to try this method after trying all other methods you found . (The last method)

    Advice : If your phone is still under warranty please visit service centre . This method may result into dead phone .

    Applicable devices : zenfone 4,zenfone 5, zenfone 6 ( CG versions)

    Condition for applicability : Only usb logo is showing and user is unable to enter into fastboot/bootloader

    First check : press power + volume up button to power on the phone and release(only) power button at time asus logo start showing( still pressing the volume up button )

    If you are able to enter into fastboot then this process is not applicable for your case. please don't use this method.

    In case after applying first check you are unable to enter fastboot :
    check these:
    • Battery is charged or not
    • Are you pressing right button ??
    • Recheck the time to release power button

    Still not able to enter into fast boot then apply the below method for entering into droidboot/fastboot .
    conclusion: your droidboot got corrupted .



    Requirements : Windows 7 pc/laptop (drivers tested on this devices)

    SECTION 1

    Drivers Required : 1. iSocUSB-Driver-Setup-1.0.4.exe
    2. xfstk-downloader-setup-1.5.1.exe

    instruction : install above driver as per ranking. follow these instruction while installing:
    1. Right click on setup
    2. Select run as administrator
    Note : while installing isoc drive system may ask you to connect your device or restart your device. Don't skip
    those steps or it will result into driver not working case. Please allow all things asked by your pc .

    Driver Checkpoint: 1. connect your device
    2. Wait for windows to install driver automatic . Below picture will pop up

    3. Right click on my computer , select "properties ". Go to "device manager". select "intel
    soc"
    3. when your phone is turned on a USB patterns and connected to the computer there
    should be two new devices, are classified under Intel Soc: CloverviewPlus Device and
    Intel Soc USB Driver . Picture :

    If both are not showing in soc section try restating your computer . Check again still no improvement then :

    Driver Required : IntelAndroidDrvSetup1.5.0.exe

    install above driver as per "instruction "

    Necessary Condition for working of tool : Driver Checkpoint condition must be met


    SECTION 2
    Step 1.1 Download folder as per your model given : zenfone 4 / zenfone 5 / zenfone 6
    Check Folder contains these files : dnx.bin , ifwi.bin , dnx_osr.bin , fastboot-2.19.img.pos.bin
    Put all files into single folder .

    Step 1.2
    Confirm the phone has been connected to the computer, which also appeared Device Manager device described above,open xFSTK DOWNLOADER
    After opening note beneath the tabs to switch to the rearmost CLVP A0 / B0 / B1




    Confirm the Device status field which shows Scanning: CLOVERVIEWPLUS TARGETS DETECTED: 1, if the last place is displayed as 0, make sure that the Device Manager inside It has detected devices.



    Step 1.3:
    Give proper path to corresponding section :

    Fw Dnx : dnx.bin
    IFWI : ifwi.bin
    OS dnx : dnx_osr.bin
    OS image : fastboot.xx.imp.pos.bin


    Then press begin download


    After the completion of the phone will automatically reboot if the boot screen becomes Intel inside patterns means you have reached your destination .
    Now you can enter into fastboot/booloader/drodboot.There are so many methods given to unbrick, soft bricked phone

    Advice: USe Adb method to recover your phone.

    Problems detected :

    Encountering " Windriver Error: 0x20000015 "

    Expected cause : Driver not installed correctly .

    Method :
    1. uninstall xfstk downloader
    2.restart computer
    3. right click on xfstk downloader and select option run as administrator .
    4. install first then open xftsk as admistrator
    5. give path to those files on xftsk as per instruction
    6. Press the Start Download button in XFSTK
    7. Then connect usb and press power + volume up button .
    Still encountering :

    Method :
    1. open Device Manager (from Windows command prompt, type devmgmt.msc)
    2. Find the device (it probably is under Android Devices.)
    3. RIght click on the device, choose "Update Driver" and then "Browse My Computer..." and then "Let me
    pick from a list of device drivers on my computer."
    4. You might have to unclick "Show Compatible Hardware"
    5. In the Manufacturer section, pick Google or Intel.
    6. Under Model, pick "Android Bootloader Interface."
    7. Click Next, and then Ok to Ignore scary warnings.
    8. Start xftsk download-er do the required thing

    If above links are dead then please go to : http://www.mediafire.com/folder/7qapfy4zqvxf6#z3i6bncz0beih

    For more knowledge visit : https://github.com/shakalaca/ZenFone-boot-tools

    Sorry for my bad English .

    Thnaks :D
    Rishav754

    still cannot unbrick my phone .. zenfone 5..always show usb logo..P_20160828_114158.jpg