Help OnePlus 5 doesn't read usb-otg and pc doesn't recognize it

[hamzah93]

hey.
i have oneplus 5 its rooted and twrp installed
i erased syetem

now i can't install any system
my pc doesn't recognize it
i enterd Qualcomm mod but it doesnt recognize it
i tried to plug a usb drive it doesnt read it
i replaced the connector and usb flex it still doesn't read it
please help me

Is there any way to copy system to twrp without usb ???


thank you

 

[KaszasM]

hey.
i have oneplus 5 its rooted and twrp installed
i erased syetem

now i can't install any system
my pc doesn't recognize it
i enterd Qualcomm mod but it doesnt recognize it
i tried to plug a usb drive it doesnt read it
i replaced the connector and usb flex it still doesn't read it
please help me
thank you

try with both side (turn cabel)
try to oush it in hard know it sounds stupid
i know it sounds stupid but i have 1 o+5 and i changed also everything allready and tryd bunch of cabels/chargers (all oem) and same **** , charge works only in 1 position too, dashcharge is just luck sometimes works sometimes not
something dies on the mainboard on that circuit
after flexchange now contactfail but still only 1 side active even that the phone recognize connection

 

[hamzah93]

I changed the usb flex and connector on mainboard
It charge but no data transfer

 

[hamzah93]

help

 

[hamzah93]

Help

 

[hamzah93]

Help

 

[brainbomb]

Might be hardware. The USB board is not soldered but connected to the manboard. Open the case and fixate. HTH

 

[hamzah93]

Help

 

[nikk95]

does the dashcharge take some wiggling to activate? @hamzah93 @KaszasM it basically means there is lots of lint in the USB-C port. USB C is known for that. Use toothpick with the sharp edge to rub inside the USB-C port to remove the lint. keep going at it for sometime as the lint is really stubborn. i had to use a safety pin and rub constantly for 2-3 minutes to get the lint out. however using metal is not suggested until you know what you're doing.

Cheers

 

[KaszasM]

does the dashcharge take some wiggling to activate? @[email protected] it basically means there is lots of lint in the USB-C port. USB C is known for that. Use toothpick with the sharp edge to rub inside the USB-C port to remove the lint. keep going at it for sometime as the lint is really stubborn. i had to use a safety pin and rub constantly for 2-3 minutes to get the lint out. however using metal is not suggested until you know what you're doing.

Cheers

most of the times its just the connector , i changed a few already ,

maybe he didn't placed well by the change or it's already **** product.
you must push all the way down once i even needed to polish the edge of the usb too, that it matches into the backcover.


in my case as i made from my phone in a hot moment a 1 + "fold" a needed to change beside the battery display backcover, even the smd connector on the board .

but all if them is still fine even the last wich i mentioned in the first post above , now with the new smd ?

take your phone to pieces and free the usb port and try your charger / even better any usb otg.

if it works the trouble is 100% that u must push "down" in the backcover let the red isolation ring dissaper in the cover , if not worked with "free" usbport order 1 more

 

[hamzah93]

I changed the connector many times
I ordered one more flex cable and dashboard
I will chang it will replay
Thank u

 

[Sandeep_Goyat]

i had the same issue. i just cleaned the charging port with some water ( i took the risk as it is splash proof) and a cloth and its even dash charging now. But do it at your own risk. i do this often when the problem occurs again.