Well it would be the two pins on the right of the picture of the first picture you posted.
In the second picture, I'm not sure since I can't tell which direction is the top of the connector.
Last edited:
[HOWTO] [REF] Get Download Mode without 3-button combo using homemade JIG
- Thread starter TheBeano
- Start date
In the second picture, I'm not sure since I can't tell which direction is the top of the connector.
gahhh upside down .. i think i have it worked out
http://i53.tinypic.com/jzdzdx.jpg
3x 100k, 1x 1k **
Yes, that's correct if the top of the connector is the side where the yellow number 3 is.
yeh now just have to learn how to solder haha and have to buy the resisters too confirm does this boot a non download samsung galaxy into download mode or only work for those who have it enabled ? cuz mine could never do it from the start since i got it ..
It worked on mine. I couldn't get into download mode using the hardware keys and ended up bricking the phone while trying to flash a new ROM using Odin. This allowed me to get back into download mode to reflash the ROM.
You might want to see if you can buy wire leads that would fit onto the pins. I don't know if they make them small enough but if they did, you could possibly avoid soldering.
You might want to see if you can buy wire leads that would fit onto the pins. I don't know if they make them small enough but if they did, you could possibly avoid soldering.
Last edited:
yeh thats exact same as mine the black screen of death lol if i buy 1x 301k resistor or 1x 300k, 1x 1k or 3x 100k, 1x 1k that all be fine ?
Ok this is my USB Please tell me if is correct
http://img38.imageshack.us/i/pin4l.jpg/
http://img221.imageshack.us/i/pin5.jpg/
http://img821.imageshack.us/img821/6296/fullviewa.jpg
Ok and i find on radioshak a 3x100k 5% 1/4w this resistor do the job?
http://img38.imageshack.us/i/pin4l.jpg/
http://img221.imageshack.us/i/pin5.jpg/
http://img821.imageshack.us/img821/6296/fullviewa.jpg
Ok and i find on radioshak a 3x100k 5% 1/4w this resistor do the job?
Last edited:
looks good but i didnt think u needed the chip and the rest of the usb cord hum... does it work ?
There isn't a chip there, that is what the back of some connectors look like (including the car charger I pulled apart last week to solder a bridge from d+ to d- to make the handset charge properly rather than trickle charge).
i pulled the chip thing off ..cuz i thought u have to solder to the pins 4 and 5 ?
There isn't a chip in that photo, it is simply a little circuit board to help mount the cable, you can solder to that, it will make things easier to support the resistor/s.
damm i kinda pulled that circut board off ... soo guess i have too solder to the pins :S
Today i ordered my battery becauce i dont have one next week when have i post how this work
one question you tink this work to me if i hva e flashed with the at&t firmware
the screen turns on with the at&t logo and then turn off , intro to never ends cicle
until i remove the battery
one question you tink this work to me if i hva e flashed with the at&t firmware
the screen turns on with the at&t logo and then turn off , intro to never ends cicle
until i remove the battery
You have the wrong bootloader on your phone now so I don't know if it will work. If you do get into download mode it would be best to try to replace the bootloader with the correct version using this method before flashing anything else.
something intresting
http://i55.tinypic.com/15rk5u9.jpg
http://i51.tinypic.com/22aljb.jpg
i pulled apart my car charger last night to get another micro usb male a port and i found this .. not sure its its all set too go.. it has a resistor on it and its connected to 1 and 2 by the looks of it can i just pull them pins out and replace em with 4 and 5 ?
http://i55.tinypic.com/15rk5u9.jpg
http://i51.tinypic.com/22aljb.jpg
i pulled apart my car charger last night to get another micro usb male a port and i found this .. not sure its its all set too go.. it has a resistor on it and its connected to 1 and 2 by the looks of it can i just pull them pins out and replace em with 4 and 5 ?
Last edited:
In this photo the resistor is already on pins 4 and 5, they are on that side of the plug (side closest to the earphone socket).
I'm ordering SKU 48640 from dealextreme to get a plug. It is a micro USB charger adapter cable.
The interesting thing is that the connector cover (on the one in the picture at least) is a hard plastic clamshell with external lips. It should be easy to open.
The interesting thing is that the connector cover (on the one in the picture at least) is a hard plastic clamshell with external lips. It should be easy to open.
thats wat i thought first but then i looked again they on 1 and 2 cuz if u turn the fone around pins 4 and 5
have nothing attatched to them.. i also have 2 more micro usb male a ports and they dont have pins 1 and 2 visable and they are closet to the ear piece ... humm..
CAN SOME ONE POST A VIDEO OF THIS BEING DONE !! ITS confusing me and i dnt wanna solder anything till i see it done thnx
just made my device
no go .. do u turn the fone on .. soo its on the black screen of death .. or do u take battery out and put back in wait a min then plug device in fone while off .. or have i put the resistors on the wrong pins they soldered on to the last 2 pins closest to the ear piece or 3.5 mm jack of the phone.... im realy stuck here and i was soo excited any help appreciated thnx
Our Apps
Get our official app!
The best way to access XDA on your phone
Nav Gestures
Add swipe gestures to any Android
One Handed Mode
Eases uses one hand with your phone