Junsun V1 Pro MTK8259 4GB + 64GB Android 10 headunit

[miroslavpena]

#1 note that changing a 8878/8888 setting will reset radio, equalizer, navigation app, ...
#2 in the 8878 settings menu (section Others) is this mysterious memory remember/unrememer setting. Give it a try but consider #1 if you change a setting
#3 remove USB drives because they may be configured to be Androids storage for app data. And maybe the app/setting is required before the USB drive is detected during boot process.
#4 re-flash current or newer firmware
#5 install logcat reader and check for errors and fatal messages while changing a setting or directly after boot.

Will try step #2 and #5 tomorrow.. thank you!

Meanwhile if you could help me with few things too please..
1. How to disable 'pop up' Air conditioning info ? Every time i change something on AC its displayed on screen and its there for few anoying seconds..and even worse every now and then by itself
2. How to turn on led lights on buttons on left side (power,home,+,-).. i found menu for changing colors but it is just completely off?
3. Is it true that if i have canbus i cannot configure steering wheel buttons in SWC as as it is now SWC won't recognise my buttons but most of them works fine (volume, next, voice ..)

Thanks again.

 

[TorstenH]

Will try step #2 and #5 tomorrow.. thank you!

Could be a good idea to check if ACC and B+ aren't swapped.

Meanwhile if you could help me with few things too please..
1. How to disable 'pop up' Air conditioning info ? Every time i change something on AC its displayed on screen and its there for few anoying seconds..and even worse every now and then by itself

I think I've seen somewhere in the 8878 menu an AC setting. Maybe it helps to turn it off. Don't know if it was in Others or Menu Icons section.
Another approach would be to disable the AC activity via an ADB command so Android blocks its execution.

2. How to turn on led lights on buttons on left side (power,home,+,-).. i found menu for changing colors but it is just completely off?

The head unit has an ILL pin. If you turn on your cars lights the ILL provides a 12V+ signal. Sure, you could also connect ACC from OEM radio connector to ILL input of the head unit to always turn on the button background illumination.

3. Is it true that if i have canbus i cannot configure steering wheel buttons in SWC as as it is now SWC won't recognise my buttons but most of them works fine (volume, next, voice ..)

Absolutely correct. But maybe your cars SWC is realized by a resistance matrix which gets exposed to the OEM radio connector. In this case you can bypass the can box, use the KEY1/KEY2 pins of your head unit and so the learning function.
You could also check if the not recognized buttons get logged (logcat reader). In this case you could use AppSwitcher app for this buttons.

Thanks again.

 

[miroslavpena]

I think I've seen somewhere in the 8878 menu an AC setting. Maybe it helps to turn it off. Don't know if it was in Others or Menu Icons section.
Another approach would be to disable the AC activity via an ADB command so Android blocks its execution.

.. disabling it in service menu doesn't help..no change it still apears on screen..

..how to do it via ADB? What's the command line? Ty

 

[ciorapel]

1. How to disable 'pop up' Air conditioning info ? Every time i change something on AC its displayed on screen and its there for few anoying seconds..and even worse every now and then by itself

In 8878 menu, you have a setting for AC type, or something like this. You have one fullscreen option (that I hate too), and two aditional bars on bottom of display; choose ac type (or something like this) 2.

 

[Zooloo_tim]

Hello, please, share with me app for S600

 

[miroslavpena]

In 8878 menu, you have a setting for AC type, or something like this. You have one fullscreen option (that I hate too), and two aditional bars on bottom of display; choose ac type (or something like this) 2.

I dont have AC type option just AC enable, disable..and on disable its still working

 

[ciorapel]

I dont have AC type option just AC enable, disable..and on disable its still working

You are right. The option is under CAN menu.

Air ui option

//edited:

 

[no_hits]

@ciorapel
@miroslavpena
and other who have problem with clearing launcher cache/settings (radio preset, brightness, DSP and EQ settings , default navi app , and so on...

I have fix this problem, maybe helps you too
1) reboot device (cold start) - about device - tap on gear and write code 4 (yes only number 4 for reboot)
2) set what you need
3) connect USB flashdrive
4) reboot again
5) disconnect USB drive

But pay attention ! ! ! ! - If you will go to advanced setup (code 8878) , for make changes , will press save and reboot - every lancher settings will be reset to factory defaults ! ! ! ! then you must do procedure above again for store launcher settings

Application Reboot.apk can be still used without any issues ;-)

 

[ciorapel]

@no_hits thank you for your suggestion, I'll try it if I ever see that my HU looses settings again, but seems like a FW update managed to make my settings stick. I can't say anything about Radio settings, as my radio app is still broken (I managed to make it work before update, but after update it got screwed again).

But I think that I misunderstood the resetting situation. If you install Reset.apk from ”for_launchers”, and reset the HU from that option, do your settings get reset ? My settings get reset on every reboot of the HU, but not after sleeping. I never got the chance to let the HU fully go into shutdown (after 3 days as I've read), to see if the setting get reset then, but the settings seem to stick from one day to another.

Thank you again for your suggestion, and I'll try it first time my HU settings get reset.

 

[no_hits]

Reset.apk not tested. Now it works for me finally, so I don't want to try other things at this moment

Let me know when you test my suggestion

 

[RUSUADRIAN]

Hello guys,i have a problem with my rearview camera,my lines are static. I tried to enable dynamic lines from setting but they are static,anyone encountered this problem?Thank you

 

[TorstenH]

Hello guys,i have a problem with my rearview camera,my lines are static. I tried to enable dynamic lines from setting but they are static,anyone encountered this problem?Thank you

Is a can bus box connected? It will not work without a can box

 

[galaxynexus789]

Hello, just installed this on an european civic 8.

My main worry is that wired android auto doesnt work, i have tried both usb connectors but cant connect, no detection. My phone is p30 pro which uses usb to USB-C

Also why are there 2 usb? On the radio side, one has more pins than the other, whats the purpose of each?

I only see android boot logos, not car brand logos (i thought there were plenty)

Gps not working, only on google maps but i think its because i connected via wifi to my phone.

 

[RUSUADRIAN]

Is a can bus box connected? It will not work without a can box

Yes is installed i think,i can use steering wheel buttons,it showing doors open.

 

[no_hits]

@galaxynexus789 you must enter to advanced setup (8878 code) and enable AA/Car play and phone link.

First USB is 3.0 (there you will Connect phone), second is 2.0 for USB flashdisk

In advanced setup you can change boot logo to your car brand too

GPS - is antena cable connected properly?

 

[galaxynexus789]

@galaxynexus789 you must enter to advanced setup (8878 code) and enable AA/Car play and phone link.

First USB is 3.0 (there you will Connect phone), second is 2.0 for USB flashdisk

In advanced setup you can change boot logo to your car brand too

GPS - is antena cable connected properly?

First of all, thank you very much!!


Why do they sell you a radio that says AA compatible but then you need to ask for help on a forum to activate it in some hidden menu? Funny...

GPS appears to be well, but ill unplug and plug again maybe i did wrong.

Again, thank you!

 

[no_hits]

It should be enable by default, but you can check it.

GPS antena should be on visible place such a dashboard or windscreen (without heating or iron tinting), not under dashboard, around wiring and covered by iron parts.

 

[Jibril14]

Hello , i want to buy an Junsun V1 Pro for a Renault Megane 3 , but since i have another brand headunit , is much cheaper to buy just the headunit without frame/cables/canbox , do you think the cables and canbox will work?
Canbox is Hiworld

 

[no_hits]

Canbox itself could work , but wiring (connector) on side of headunit could have different connection. IMO I recommend to buy whole set.

 

[Jibril14]

Thanks, its true that while it looks the same , pin layout may be different , whole set it is then.