Had it also some time, but it's gone fine again.
As far as i discovered it seems it's a slightly damaged usb port or some dirt inside. Most likely due to heavy usage of docking and so on. Imo hardware problem.
Cheers, Olioaglio
Sent from my SGS3
[KERNEL][01APR][JB][SAMMY&CM] SiyahKernel S3 v1.9.1
- Thread starter gokhanmoral
- Start date
Had it also some time, but it's gone fine again.
As far as i discovered it seems it's a slightly damaged usb port or some dirt inside. Most likely due to heavy usage of docking and so on. Imo hardware problem.
Cheers, Olioaglio
Sent from my SGS3
It comes with the Sammy based Rom. Your dev might see it as"bloatware"though, I will post a screenshot later in a pm to you since this is a dev thread related to Siyah and not Sammy based roms.
Sent from my GT-I9300 using xda app-developers app
WARNING!!!! Siah 1.8.6 IS vulnerable to sudden death
PLEASE READ http://xdaforums.com/showthread.php?t=2091045
My S3 just died one hour ago from "sudden death" :crying:
Was with omega v.36 (xella) & siah 1.8.6
quote "Please be aware, this is not related to the Exynos Memory security issue.
The "Sudden Death" issue is caused by firmware on the (16 GB) VTU00M, revision 0xf1 eMMC (Embedded MultiMedia Card or internal memory if you like). Samsungs Kernel Source Code (Update 7) has been identified as the fix. There is still no evidence that the latest sboot bootloader addresses this issue. " unquote
the following thread explains wich kernels are "safe".
http://xdaforums.com/showthread.php?t=2091045
my post about my S3 sudden death: http://xdaforums.com/showpost.php?p=36662289&postcount=3301
PLEASE READ http://xdaforums.com/showthread.php?t=2091045
My S3 just died one hour ago from "sudden death" :crying:
Was with omega v.36 (xella) & siah 1.8.6
quote "Please be aware, this is not related to the Exynos Memory security issue.
The "Sudden Death" issue is caused by firmware on the (16 GB) VTU00M, revision 0xf1 eMMC (Embedded MultiMedia Card or internal memory if you like). Samsungs Kernel Source Code (Update 7) has been identified as the fix. There is still no evidence that the latest sboot bootloader addresses this issue. " unquote
the following thread explains wich kernels are "safe".
http://xdaforums.com/showthread.php?t=2091045
my post about my S3 sudden death: http://xdaforums.com/showpost.php?p=36662289&postcount=3301
Last edited:
Wow with devices dying left and right, people who still use Siyah and know about the SDS issue have some ba**s. Siyah is a brilliant Kernel but without the fix in my opinion too dangerous to use. I can recall several cases just in the last days where devices died using the latest Siyah Kernel.
Man I hope that gokhanmoral will be back soon.
Man I hope that gokhanmoral will be back soon.
I read on the siyah kernel official side that next version supports cm 10.1. does it mean only cm 10.1 or every 4.2.1 build? and when will it be published?
I agree. without the fix it is very dangerous. stay away... run... but also keep in mind that it is not more dangerous than before because that bug was always here since the beginning.
I could only read 9-10 pages back and it seems that the only major issue is SDS.
and it "seems" that samsung made some changes to fix that.
I will be releasing 1.8.7 which is based fully on i9300-update7 sources, in an hour I hope.
Well there you have it. :good:
gokhanmoral a quick question, why is it not possible to tweak the in call volume of the front speaker in STweaks?
Why only rear speaker and headphones volume? This setting is so much needed on some ROM's. Specially on AOSP/AOKP roms.
WOW Gokhan, I think most of all of us are really glad to hear that, and truly glad to see you back, welcome back
Last edited:
ok v1.8.7 is up.
it's not a big update. just rebased the kernel on i9300 update7 sources.
exynos-mem and sudden death issues are supposed to be fixed.
I have tested the kernel on cm10.1 (latest nightly) and samsung JB (as secondary) roms.
there are tiny changes in ramfs to move .secondrom folder back to sdcard root after you install cm10.1. so, you should not have any problems after installing cm10.1 for the first time.
I'll be around more next week and I have some new features in mind.
I hope my skills are not rotten after spending about a month on higher realms (.NET and Java)
it's not a big update. just rebased the kernel on i9300 update7 sources.
exynos-mem and sudden death issues are supposed to be fixed.
I have tested the kernel on cm10.1 (latest nightly) and samsung JB (as secondary) roms.
there are tiny changes in ramfs to move .secondrom folder back to sdcard root after you install cm10.1. so, you should not have any problems after installing cm10.1 for the first time.
I'll be around more next week and I have some new features in mind.
I hope my skills are not rotten after spending about a month on higher realms (.NET and Java)
Good to see you back!
If you find some time...I have missed one small option in stweaks "mdnie tweaks" or hardcore tweaks it was present in your older versions. Dont like the tweaks though
making the screen blurry.So the option for disabling it would be nice
Sent from my GT-I9300 using xda app-developers app
Thanksok v1.8.7 is up.
it's not a big update. just rebased the kernel on i9300 update7 sources.
exynos-mem and sudden death issues are supposed to be fixed.
I have tested the kernel on cm10.1 (latest nightly) and samsung JB (as secondary) roms.
there are tiny changes in ramfs to move .secondrom folder back to sdcard root after you install cm10.1. so, you should not have any problems after installing cm10.1 for the first time.
I'll be around more next week and I have some new features in mind.
I hope my skills are not rotten after spending about a month on higher realms (.NET and Java)
Inviato dal mio GT-I9300 con Tapatalk 2
ok v1.8.7 is up.
it's not a big update. just rebased the kernel on i9300 update7 sources.
exynos-mem and sudden death issues are supposed to be fixed.
I have tested the kernel on cm10.1 (latest nightly) and samsung JB (as secondary) roms.
there are tiny changes in ramfs to move .secondrom folder back to sdcard root after you install cm10.1. so, you should not have any problems after installing cm10.1 for the first time.
I'll be around more next week and I have some new features in mind.
I hope my skills are not rotten after spending about a month on higher realms (.NET and Java)
Hi, just a small question. If we flash kernel as recovery it will work as Recovery or you ended with this project? Also, Recovery its based in latest Update Samsung since i read that also Recovery Samsung made changes to prevent the SDs ...
Thanks in advance.
I have philz touch recovery to be safe for sds.
Can i install the hijack recovery and iam safe too with 1.8.7?
Can i install the hijack recovery and iam safe too with 1.8.7?
Similar threads
- Locked
- Poll
Top Liked Posts
-
There are no posts matching your filters.
-
1159Please leave non-development related posts to the discussion thread in general section: http://xdaforums.com/showthread.php?p=27389678
STOP! This kernel supports ONLY Samsung JellyBean or CM10.1 ROMs. It won't work on ICS, CM9.
Sources :-
Sources at http://github.com/gokhanmoral/siyahkernel-sgs3
Ramfs at http://github.com/gokhanmoral/ramfs-sgs3
Toolchain at http://github.com/gokhanmoral/android_prebuilt
Simply clone all to a directory and run build_kernel.sh in the kernel directoryFeatures :-
- Samsung and CM10.1 support with a single kernel image
- based on i9300 update9 sources
- CPU OC/UC/UV
- GPU OC/UC/UV (5 step GPU clock)
- Audio enhancement and sound boosting for great headphone experience (partial-port of wm8994 based implementation from project-voodoo)
- init.d support
- Triangle-away app support
- Auto-root
- Adjustable charging speeds for AC and USB
- Automatic EFS Backup
- Samsung proprietary ExFat modules are loaded. Don't ask about ExFat support for aosp roms in this thread.
- Kernel based gestures support by Tungstwenty. See http://xdaforums.com/showthread.php?t=1831254
- NTFS automounting for USB sticks, mounted to /mnt/ntfs folder in Read Only mode.
- mDNIe negative effect toggle with 4 consecutive press of home button
- mDNIe values can be adjusted using the interfaces in /sys/class/misc/mdnie.
- Almost everything is configurable via simple and free STweaks (included in the kernel or from Google Play)
- Dual-booting. You can have Samsung JB and CM10 ROMs on a single device at the same time.
- slide2wake (WIP, still incomplete)
Known Problems :-
- No known problems.
Thanks To :-
Chainfire, AndreiLux, Tegrak, Entropy512, Netarchy, Pikachu, Tungstwenty, Codeworkx, XploDwilD- This part will be expanded. most of the patches I applied are coded by someone else. please remind me if I forget to give credits to anybody..
Todo:
these are my future plans and some of them are dreams only...
- fix bugs
- add optional teamwin recovery
- implement BFN (BackFlashNotification)
Video Review of v1.7rc1 by KingRamo
308
IRC support and chat:
Server: irc.FreeNode.net
Channel: #siyah-kernel
web client: http://siyah.twosx.net/ (thanks to omniwolf)
READ THESE FIRST
- First thing you need to have before posting to this thread is respect. If you don't have it for others you will regret leaving a post as people in this thread don't like disrespect. The items below are just detailed description of what "respect" means in this context. If you have common sense you probably won't need to read all the following items but please do read them anyway.
- Never report any bugs to CM9/CM10 thread if you use it together with SiyahKernel
- Do not ask questions to me directly. This is a common thread, not my personal inbox. Ask your questions in the thread and do not target them to anyone.
- Do not expect answers to all your questions. There are some questions which nobody knows the answer of.
- Do not forget that this is a development thread. There is another thread in general section for those who wants to discuss battery life and chats. If your post does not include a feature request, bug report or suggestion it should be posted to the other thread.
- Make sure you state your ROM, settings and any other relevant information while telling about your problem/a bug. "I have lag", "I had crash" or any similar posts will be ignored if you don't give any more details.
- No ETA for new version. Even if I sometimes talk about release dates those may change and they change for some good reason or because of my real-life obligations.
- Make use of "Search this Thread -> Advanced Search". If you humiliate people and waste their time by asking a question which is answered in the last 3 pages I guarantee that you will be treated as you deserve.
- You need STweaks app to configure/change most of the features in this kernel. However it is not required if you don't want to modify anything.
- Never ever discuss anything deep-sleep related in this thread. I do not make modifications to prevent sleep and 99% of deep sleep problems are application/ROM related. discuss it in general section. I do not want any positive ("this kernel sleeps like a baby") or negative ("There is a big problem with deep sleep. Please fix it") messages in my development thread.
- I am not interested in any bug reports if you undervolt your device. I don't want ANY kind of undervolting related discussions or bug reports in this thread.
204
Useful Links:
- Almost everything that you need to know about Kernels, schedulers and so by droidphile
- Another great post explaining more and ICS differences by droidphile
- Although I put it in the first post, this is my github for kernel sources, initramfs and some more
- You can find all the answers you need here, even those that I don't know
145Know the STweaks Tunables
You have a custom kernel and an app to control different tweaks. Read below to have a fair understanding of all the sliders and drop-downs in the app plus read some faqs.
Q. "What's STweaks?"
A. It's an app developed by GM to provide a simple interface for various kernel tweaks.
STweaks works using /res/uci.sh interface. (Universal Configurator Interface). Ideally when you run /res/uci.sh config you get an xml file. The app render that XML file to an UI. (The xml is customconfig.xml in /res/customconfig directory)
Q. "Where are profile files (default, performance etc) stored in my device?"
A. /data/.siyah with extension ".profile"
Contents are in the format <tunable> = <value>
Q. "How come STweaks takes a little long to load every time? Other CPU tuner apps like SetCPU opens faster!"
A.Stweaks needs to query the values of ALL tunables from the active profile file, then set the UI elements (sliders, checkboxes, dropdowns, etc) to match the values queried. Only after these it can expose itself for you. So yeah! Some time is needed.
It loads in about 2 seconds now.
Q. "So every tunable possible with SiyahKernel is included in STweaks?"
A. NO. That would make the app complicated and while some users like to have lotttsa tweaks in the app, some users prefer the opposite. So to be fair, STweaks will not be cluttered with way too many options.
For users who know what they're doing, there are scripts, and kmemhelper.
Q. "After flashing a new version of Siyah, I can't see STweaks in my app drawer. Help!!"
A. Using a Root File Explorer, copy STweaks.apk from /res directory to /system/app. Set permissions rw- r-- r--
Q. "I find that after flashing a new kernel version, while adjusting some tunables there's no effect."
A. In the app, under EXTRAS Tab, hit "Reset settings to default". Now reconfigure all your settings. Should be fine in most cases.
Q. "Sometimes, after flashing a new kernel build, i see all my settings are reset to kernel defaults. Is it normal?"
A. YES. It's just so that profile files contains all the tunables matching config XML in the latest build. If resetting is not done, some settings will not work.
Q. "Does that mean - every time I flash a new kernel build, I need to reset settings?"
A. NO
Q. "What should I change in STweaks to have best battery/best performance?"
A. Read below to know what each tunables do. If you still don't get it, don't change anything. Trust defaults. All will be good.
1) CPU Tab
Gentle_Fair_Sleepers:-
This is a CFS tweak. CFS aka Completely Fair Scheduler is your default Task Scheduler. Task Scheduler is responsible to manage task executions - decides what task to execute next from a queue. CFS scheduler tries to fairly distribute the CPU time among all tasks in such a way that each of them gets the same amount of the virtual run-time. CFS maintains two arrays - active and expired. Tasks once served from active array are placed in expired array. When there are no more tasks in active array, the two arrays are swapped. Sleeper Fairness means to consider sleeping tasks similar to the ones on the runqueue and credit the sleepers in a way that it would get CPU as if it were running. With Gentle_Fair_Sleepers enabled, sleeping tasks will get a little bonus time w.r.t to their virtual run time. While this may seem fair in some cases, disabling this tweak may possibly improve UI responsiveness:- may be because sleeping tasks are not given additional priority and the task that's responsible for UI do not sleep while screen is ON.
* Arch_Power:-
Another scheduler tweak. Helps in using specific ARM topology functions instead of generic functions. Benefits may include idle higher number of threads in a core, etc.
* CFS Tweaks:-
Three options which sets different value for your task scheduler's a) Minimum Granularity b) Latency c) Wake-up Granularity
A new "epoch" or a new time origin begins when scheduler swaps active and expired array.
Latency is the length of an epoch in nano seconds.
Minimum Granularity is the granularity of one epoch.
Wake Up Granularity is the ability of tasks being waken up to preempt the current task (5 ms by default). The larger the value the more difficult it is for the task to force the preemption.
- Samsung Defaults:- Leave it as Samsung defaults if you want higher benches.
-Linux Kernel Defaults:- My fav.
-Thunderbolt Scripts Defaults:- Pikachu's tweaks are aggressive low values for parameters. May improve UI responsiveness.
CPU Idle Modes:-
Leave it as Idle+Lpa. AFTR seems to be a difficult world to conquer for i9300.
* Smooth Scaling Level:-
Leave it as 1800mhz (which disables smooth scaling) if your governor has the parameter "freq_step" (ex: Pegasusq). Otherwise, the two concepts may conflict. Use smooth scaling for other supported governors. CPU driver scales CPU to frequency as defined by Smooth Scaling Level before jumping to Max Frequency.
Sched_mc:-
Leave it disabled = 0. 1 will overload first core, 2 will try to save power by biasing task-wakeups to semi-idle core.
CPU Undervolting:-
[Courtesy Andreilux for the info] 32 nm Exynos 4412 on our device decreases the need for higher voltages for transistors to switch and decreases voltage leakage. So they actually successfully switch more of the time compared to SiON on Galaxy S2 i9100 where leakage was big enough to not make a transistor switch and crash the system. In short, this is why GS3 supports higher UV compared to GS2. You might be lucky enough to UV more than 200mv on certain frequencies. Try on own risk.
Max CPU Lock:-
Defines no of cores to be used along with Pegasusq governor. Leave it quad core. You have beast of a phone. This parameter actually changes the max_cpu_lock parameter of your governor - pegasusq or lulzactiveq.
CPU Governor:-
Use Pegasusq.
CPU Max Frequency:-
Sensible OC for our device is 1.5 Ghz. You can try more and see what happens.
CPU Minimum Frequency:-
Use 200 or 100.
2) CPU_UV Tab
Like SetCPU or voltage control, sets voltage per CPU frequency. Note that the values DO NOT represent the actual voltage levels on the frequencies. If you UV in Stweaks and also use SetCPU to set voltage levels, SetCPU will over ride Stweaks.
3) GPU Tab
* Mali Touch Boost Level:-
If this option is enabled to any steps, when you touch on the screen/press soft back or menu keys/press homebutton - GPU voltage is set to the GPU step that match the step set by you here and frequency is set to that step. This may helps in better responsiveness of unlocking via lockscreen, etc. Note that, this doesn't mean GPU is locked to that forever. After one second, depending on thresholds and stepcounts, soon GPU is clocked down or up.
If Mali Touch Boost Level is disabled, GPU resumes at lowest frequency (your first step).
GPU Frequency Steps:-
Now we have frequency steps taken from Korean sources, as hard coded in clock-exynos4212 file. You won't find a formula to calculate valid frequency steps. (Unlike i9100 for which any GPU step was 800 divided by an integer)
GPU Voltage Levels:-
You may be able to UV a little more compared to GS2 if your ex device was GS2. Try and see. (Thanks to 32 NM SoC). Remember that you will know UV was too much only while GPU is being heavily used - like gaming.
GPU Thresholds:-
If you're not sure about this, use default thresholds. Wrong thresholds can cause lags.
* GPU Stay Counts:-
Stay count is the number of Seconds GPU should stay at a frequency level before it can scale up or down, overriding "load exceeds threshold condition". To avoid any possible stutters in gaming, use staycount = 1 second for the last step. May be for 4th step too, just to be sure.
If you don't find StayCount interface in the app, use script.
echo "0 0 0 0 1" > /sys/class/misc/mali_control/staycount_control
From left to right, each digit represents StayCount for lowest to highest GPU frequency steps.
4) AUDIO Tab
Speaker Tuning:-
Check to enable better bass response on speakers. Note that GS3 speakers don't play well with bass (even with open source audio HAL developed by codeworkx for CM10. So if you find sound distorting on speakers, uncheck this option instead of trying to play with some equalizer.
Speaker Amplification Offset:-
Default zero. Increase to amplify speaker volume. At level 5 or 6, speaker is most likely to distort playing ringtones/sounds.
Headphone Amplifier:-
Volume boost for your headphones. Level 0 = -57 dB. Level 63 = +6 dB which is the hardware maximum. Please take care of your hearing.
3D Effect:-
Stereo expansion may tighten the stereo field. In general, there are multiple techniques to achieve surround effect/3d effect/stereo expansion effect.
3D Effect Gain:-
Valid only if 3d effect is enabled. Higher value may not sound pleasant to most ears. 2-4 should do.
EQ Presets:-
Use inbuilt presets or use graphical equalizer bands to tune the 5 band equalizer.
Graphical Equalizer:-
The five band equalizer(with a range of -12dB to +12dB) is a hardware equalizer. So it controls all the sound coming from your headphones. Software equalizers such as inbuilt EQ of powerampp can only control the sound output 'formatted' by this 5 band h/w EQ. As you know, the first two bands - Lows/Bass. Middle one - Mids/Vocal and last two bands for - Highs/Treble.
Negative Digital Gain:-
Or dynamic range. Increase this to prevent distortion. It defines how much volume is to be digitally reduced from headphone amplification level.
FLL Tuning:-
Aka Anti Jitter is an audio enhancement technique as an internal clock optimization to reduce noise and produce a better quality sound.
DAC Oversampling:-
Increases dac oversample rate for a 48 khz rate and produce better outpund sound.
DAC Direct:-
Aka DAC ME, Bypass analog channels and redirect sound directly to output.
Mono Downmix/Force Mono:-
Force mono sound even if source is stereo.
5) SCREEN TAB
* MIN_BL, MIN_GAMMA, MAX_GAMMA:-
In simplest form, set this higher to have lower brightness at bright conditions on automatic-brightness settings. And vice-verse.
We have lowest brightness for a brightness level read from sensor less than min_bl. Any level higher than min_bl will be linearly mapped to min_gamma:max_gamma to interpret brightness of the display. Difference between min_gamma and max_gamma along with their values affect overall brightness response curve.
mDNIe Sharpness Tweaks:-
Makes thin fonts more readable. You're most likely to see weird display if you disable this option.
mDNIe Negative Toggle:-
If this is enabled, quickly pressing home key four times will invert all the colors on your scree. Useful for ex: Reading a webpage in the dark which has white background by default. By inverting colors to make it black, your eyes will strain lesser, plus it saves battery in such cases.
Touch Boost Level:-
Defines the frequency to which CPU is instantly ramped up to when we touch the screen. Advantage? UI responsiveness. Setting this too low might be a v bad idea on some devices.
Slide2Wake:-
If enabled, slide on screen in a straight fashion from left to right to wake your device. Helps prevent wear down of physical home/power buttons. If in doubt this drains more battery, leave it disabled.
FB Early Suspend Delay:-
Early suspend delay to run CRT off animation. If you're sure that Settings > Developer Options > Windows Animation Scale is 1x or higher (not 0.5x or off) and still can't get CRT-off animation to work, set this param to 100 ms or so.
6) MISC TAB
Android Logger:-
Enable disable android logger. Logger hardly uses any extra battery, and will be very useful if to pull a log after a crash or freeze. Leave it enabled.
* Insecure Adbd:-
Enables to run your Android Debugging Bridge Daemon (adbd) in root mode by default. Use "adb remount" command in a terminal to mount /system as r/w.
I/O Scheduler:-
Use any among deadline/sio/noop.
* Zram Size:-
Compressed swap space aka compcache aka zram allocates defined amount of space from your physical RAM as compressed swap space. You can debate all along to see if zram is useful on a fast device like GS3 with a fast flash storage inside. If in doubt, disable this option.
Notification LED Behavior:-
Force blinking/fading of notification LEDs. Useful for Sammy based roms. (aosp roms has blinking/fading setting inbuilt).
AC Charge:-
Charge current from your wall charger. Increase the value for faster charging at own risk. If you see currentwidget app displaying only 800/1000 mA (when you have set 1200 mA in stweaks) while connected to car charger - it's because the charger can not output more current than that.
USB Charge:-
Charge from usb charger. Increase at the risk of possible damage to PC motherboard. (if it's an old board)
Discrete Wakelock Status:-
Helps betterbatterystats app to report deleted and non-overlapping wakelocks. You may see new wakelocks like your mailclient-inbox-sync, etc if this option is enabled.
Remove Root:-
Some apps detect root and refuse to work if found (certain banking apps for example). To remove root, click this button, run your app and re-enable root when you're done.
Auto Install Root:-
Tries to install superuser apk and binary. If it fails, download latest superuser flashable zip from here and flash in recovery OR download SuperSU from playstore.
6) DUALBOOT TAB
Reboot into 2ndRom Utils:-
Reboots to alternate recovery where you can configure and play with dual boot options. This doesn't change your cwm recovery, but just runs an alternate recovery.
Reboot into 1stRom:-
As it says, reboot to 1st rom without displaying a timeout.
Reboot into 2ndRom:-
As it says, reboot to 2nd rom without displaying a timeout.
No boot logo:-
Check this to disable Siyah bootlogo displayed during dual-boot rom selection time out. (If you're dual booting, logo will be shown anyhow)
Default Rom:-
Specified the default rom (among 1st and 2nd) to which device will boot into, if no keys are pressed during boot. If 2nd rom is default, pressing home/vol down keys will boot 1st rom.
Hijack Recovery:-
We know the second rom utilities aka embedded recovery is a part of the kernel - it holds the same partition as kernel. You can use this button to flash the embedded recovery to main recovery partition (overwriting your existing recovery) so that 3 button method/booting to recovery using extended power menu will take you to Siyah recovery. This is NOT a dangerous operation. You can flash cwm/twrp recovery anytime if you need another recovery.
7) EXTRAS TAB
Reset Settings to Default:-
Reset the profile file, and resets all values in device files to kernel defaults.
Check for Updates:-
Checks and downloads a new build.
Flash Kernel:-
Flash a .tar kernel. Alternative to Mobile Odin!
* Indicates tunables removed from STweaks as of now.
Flashable Zips
Update: Find sample Stweaks Profiles as flashable zip here. http://xdaforums.com/showthread.php?t=2034981. Profiles after flashing will be available in the profile app.
Here are 5 Governor Tweaks scripts as flashable zips.
Flash remove_governor_tweaks zip to remove init.d script that contains governor tweaks. One governor zip can be flashed over another and it will just replace the previous. All governor tweak scrips contains tweaks for pegasusq and luzactiveq. Gamerstweaks is also a governor script that's similar to extremeperformance script but does some additional GPU tuning (for which there is no interface in Stweaks) to enhance gaming experience.
Since order of execution is like this:-
1) STweaks applies its settings
2) Init.d scripts are executed
3) Apps such as SetCPU applies its "set on boot" options,
Script applies the tweaks to the governor selected in Stweaks (depending on if it's pegasusq or lulzactiveq). So if you want pegasuq tweaks to be applied, make sure pegasusq is the default governor in stweaks, and same for luzactiveq.
I will keep updating zips while new kernel builds are released - if it changes any tunable.142
