Thats interesting, i wonder how mutch
Unfortunately, 839MHz not stable for me, i tried fastcharging my phone, no luck. I think the heat is the main problem, i get shuttering, after it hits 90C. Anyway, thanks for the tip.
[KERNEL] [9] A2N Kernel For Galaxy S8/S8+/Note8 [EXYNOS] [HIGH-END] [STABLE] [V. 2022.07.01]
- Thread starter ace2nutzer
- Start date
If you have DVFS at 90C, its obvious. Rise the GPU Voltage and enable battery idle, as well as put DVFS to 100C. If it still doesn’t work, yeah you probably lost the silicon lottery.
I tried lots of different voltage settings without luck. The most shutter free voltage is 700mV, if i set it higher, i have more cpu spikes/shuttering. (Dvfs is 100C)
Then there has to be a lack of power. Instability in the overclock is when the phone freezes and reboots. But if you have stuttering, that GPU isn’t being fed enough. Check battery voltage while fast charging and check the charger’s voltage. I recommend using the original Samsung fast charger. Benchmarks have to be run while the phone is fast charging, with battery idle on.
@rtyuakatsuki @Pistero07
Thanks for the logs. DEX errors are now fixed. Did you guys notice some improvement or new DEX feature ?
@rtyuakatsuki
So you set 3500 mA then connect USB-PD with 12V support and in A2N app "input current" shows 9V you say.
OK, now try to set 1000 mA then connect USB-PD, then it should show 5V I think. Let me know please.
Thanks for the logs. DEX errors are now fixed. Did you guys notice some improvement or new DEX feature ?
@rtyuakatsuki
So you set 3500 mA then connect USB-PD with 12V support and in A2N app "input current" shows 9V you say.
OK, now try to set 1000 mA then connect USB-PD, then it should show 5V I think. Let me know please.
for dex i notice the improvemet more smooth than before and for charging when i set it to 1000ma and re plug the charger that still 9v
Last edited:
@ up
Alright, then it's OK. USB-PD seems to be different from AFC chargers.
On AFC charger we can decide if it should run at 5 or 9V, while with USB-PD charger the input voltage is selected automatically by the driver.
Anyway, not a big issue since the power delivered from 9V is enough to provide the 3,5A. So there is no reason to switch to 12V for the driver.
Also the charger chip inside the phone heats more up the higher the voltage is. So with an AFC charger with 9V support it should work @ 12V.
As for DEX: yes this is what I was expecting. And on next build it'll work even better. (reduced kmsg spamming)
@TechNoobForSale
I've checked CPU/GPU governor and DVFS driver if there is something wrong with CPU/GPU max possible Freqs and there is nothing wrong.
@madhatter57
Actually I'm adding a new feature for adjusting pm_qos required CPU Freq for UHQ audio playback. Also the ability to move audioserver to big CPU. This is to fix audio issues while screen OFF and to reduce power consumption. (Because you set Freq as needed)
Alright, then it's OK. USB-PD seems to be different from AFC chargers.
On AFC charger we can decide if it should run at 5 or 9V, while with USB-PD charger the input voltage is selected automatically by the driver.
Anyway, not a big issue since the power delivered from 9V is enough to provide the 3,5A. So there is no reason to switch to 12V for the driver.
Also the charger chip inside the phone heats more up the higher the voltage is. So with an AFC charger with 9V support it should work @ 12V.
As for DEX: yes this is what I was expecting. And on next build it'll work even better. (reduced kmsg spamming)
@TechNoobForSale
I've checked CPU/GPU governor and DVFS driver if there is something wrong with CPU/GPU max possible Freqs and there is nothing wrong.
@madhatter57
Actually I'm adding a new feature for adjusting pm_qos required CPU Freq for UHQ audio playback. Also the ability to move audioserver to big CPU. This is to fix audio issues while screen OFF and to reduce power consumption. (Because you set Freq as needed)
Ace I never said that there’s something wrong with your DVFS driver. I think that my results from the other day were flawed because my whole system was unstable because of FS corruption. So maybe I can handle 2704MHz too but I can’t do any testing since it seems that this hardware really does not like sub 10C temps.
Hi my friend ! - Sorry but there is literally nothing. Please copy paste the message in a new conversation, don't use our old thread. I did some cleanups a few days ago, maybe I've mess it up lol.
Yeah, I mean we was talking that maybe there is something wrong with GPU governor due to the weird lags @ 839 MHz GPU. But unfortunately everything right, so it's just power issue. Or maybe you will need to move audioserver to big CPU if the game or benchmark tries to sync video with audio .. you know what I mean ?
Wait. A question. Does audioserver remain active even if I literally run benchmarks with volume at 0? (which is what I always do)
Sure, volume=0 won't stop audio playback. You save only some little power from the audio AMP. But since it runs on little CPU by default, it doesn't effect much the benchmark. Also the bench doesn't use UHQ audio processing.
Kernel && App Update !!
Changelog
Kernel V. 2022.07.01
A2N Kernel Control V. 5.0
Version Info
If you face audio stuttering with this version you can increase the UHQ PM-QOS Freq in A2N app in "Audio" section.
If you don't have the full version, you can run a cmd like this:
Changelog
Kernel V. 2022.07.01
- DEX: bug fix for 3rd-party HDMI adapters
- DVFS table: removed hardcoded OV for big CPU by me
- Reduced power consumption for IDLE + low Freq steps (especially for Note8)
- UHQ Audio: exported pm_qos_lit to userspace (to fix audio scratching)
A2N Kernel Control V. 5.0
- Audio: added UHQ pm_qos_lit control (to fix audio scratching)
Version Info
If you face audio stuttering with this version you can increase the UHQ PM-QOS Freq in A2N app in "Audio" section.
If you don't have the full version, you can run a cmd like this:
Last edited:
Maybe the file is damaged. You should also try with another odin version, just to be sure.
Download twrp file at first page there is a twrp file
Try different usb cable. I had similar problem, my usb cable worked perfectly, but some reason ODIN failed to upload image file.
Similar threads
Top Liked Posts
-
There are no posts matching your filters.
-
4
Yes but probably it's locked like all the other clocks it was. So it needs first some hacks like always. I remember on Ace 2 we OC'ed lcd_clk from 50 MHz up to 100 MHz. 100 MHz was sometimes unstable, but 80 MHz worked stable. Now that "50" is just LCD_CLK not refresh_rate. Also I don't know how it should be calculated ... 50 MHz = 60 hz and @ 100 Mhz = 120 Hz lol. Anyway at 80 MHz, probably around 100 Hz was it possible to scroll text without to cause eye cancer. Here on S8 there is also such LCD_CLK, but even increasing it, I don't see any difference, maybe I'll try this once again. There is also refresh value = 60, but even changing this @ 100, just changes nothing, so I suspect it's locked like I said.
Yes, that's right, because it gets out of sync. @ 80 or 100 hz it'll run probably smooth without the need to adapt other stuff in ROM, which is way more complicated.
Good idea, I'll see if I can do something.3OK guys I'm trying to make a new release that should fix high quality audio when using too much filters and slow screen orentation. Other than that I'm missing something else ?3
Nope, this is not how it should be done. You need Linux OS (e.g. Lubuntu) with installed "git" versioning system.
On GitHub create an new repository.
On the root of kernel source where u've the Makefile...
first of all, check if there is a (hidden) ".gitignore" file with following content: (if not, create it)
Then just open new terminal emulator and type: this: (I suggest to start from stock source code, then properly commit your changes)
NOTE: if your local git repo is already initialized, then skip the first 3 cmds. To check this, just type: "git log" if you see already some commits then it's already initialized.
Code:git init git add . git commit -am "initial commit" git remote add master https://github.com/opensourcefreak/KOLUMN_Kernel.git git push --set-upstream master master
Later if you do some changes, just commit them and push it to your git repo:
Code:git commit -am "CPU: added OC support" git push
With "git status" and "git diff", you can always check your changes before you commit them.
EDIT:
First of all, delete your Git repo, click on "Settings" then scroll down to the "Danger Zone".3
This man is unstoppable@TechNoobForSale @rtyuakatsuki and others !
HERE WE GO AGAIN
First boot with OC'ed RAM 1,8 GHz @ 2,0 GHz:
Code:dreamlte:/sys/class/devfreq/17000010.devfreq_mif $ cat time_in_state 2093000 0 2002000 174816 1794000 4206 1540000 7140 1352000 11904 1014000 1614 845000 58046 676000 0 546000 0 421000 0 286000 0 208000 0
2,1 GHz should work as well ...
🥹🥹🥹🥹🥹
Stop making this phone faster it’s actually beating my Note 9 
CRAZY
But keep going. I support you
100% willing to test when next build drops3Me: Runs M2 cores at 4x2704MHz
The phone: Stable
Me:
CPU temp after opening Devcheck: 99°C
Me:
-
74Supports all S8 / S8 Plus / Note8 Exynos Variants Running Android 9
This Kernel Aims are to
- reduce the power consumption
- reduce device heat
- improve the performance
- make it more smooth
- reduce RAM usage
- improve RAM management
- extend device features
- and many more ...
A2N Kernel Special Features
- charger control
- battery IDLE and battery care
- stable CPU OC up to 4 x 2,7 GHz - thanks to my custom DVFS driver
- stable GPU OC up to 839 MHz - thanks @ me lol
- adjustable CPU / GPU / Battery Max Temp
- voltage control for all clocks (CPU lit/big - GPU - RAM - bus clocks etc..)
- fixed time to full battery
- flashlight tuning
- wireguard support - always latest version
- DriveDroid support
- Dex with any HDMI adapter - thanks @ Barna Keresztes
- Samsung Dex: WQHD support with every adapter - thanks @ craftingmod
- higher SOT - with new battery up to 10 h, with old battery see screenshots
- Wi-Fi calling & VoLTE works
- S8: RAM upgrade - 3679 @ 3717 MB
- Note8: RAM upgrade - 5339 @ 5376 MB
- unlocked higher CPU Freq steps - thanks @Noxxxious for initial CPU OC
- SELinux in permissive mode - thanks @Noxxxious
- fake enforce for SELinux (you can enable it in a2n demo app)
- DRM - L3 stable streaming
- SafetyNet bypass (you need to enable "MagiskHide" in "Magisk" APK
- Google Play - certified device
- replaced SSWAP with zRam - fast LZ4 compressor
- optional filesystem: NTFS
- kernel modules for CIFS and NFS
- optional device encryption
- HMP driver fix
- extra gamepads drivers: Xbox / Sony PS / Nintendo Wii
- ability to OC CPU only for screen on
A2N Kernel Control
Best way to tune this kernel to your needs
# App Features #
# Power
-- Charger Control
For faster charging. - Range: 100 - 3000 / 3300 / 3500 mA (S8 / Note8 / S8+)
-- Battery Informations
Like accepted charging current, input voltage, battery temperature and battery voltage.
-- Battery Care
E.g. stop charging at 95 % to reduce battery aging. - Range: 50 - 100 %
Battery IDLE feature, useful for DeX or gaming.
Set Max charging temperature. - Range: 30 - 45 °C
-- Battery Service
Shows charge cycles and ability to reset to 0.
Check real battery capacity in % / mAh and ability to reset. (battery gauge recalibration)
-- Disable (Buggy) Moisture Detection
Ability to disable moisture detection, for the case the USB and Jack-port is dry but you get still a moisture warning.
# Screen
-- Input Booster
Adjust touch boost CPU duration in ms, to improve scrolling.
# CPU
-- Overclock Control
BIG CPU: 741 - 2808 MHz* - default: 2314 MHz
LITTLE CPU: 455 - 2002 MHz* - default: 1690 MHz
Set Max Freq for screen OFF.
Ability to disable boost, for powersave.
Governor up_threshold, to adjust balance between performance and powersave.
BIG CPU DVFS Max Temp (thermal throttling)** - Range: 45 - 100 °C
# GPU
-- Overclock Control
260 - 839 MHz* - default: 546 MHz
Ability to disable boost, for powersave.
Governor up_threshold, to adjust balance between performance and powersave.
GPU DVFS Max Temp (thermal throttling)** - Range: 45 - 100 °C
* Max stable Freq depends on the quality of the SoC !
** To avoid too big performance drops from stock thermal throttling driver.
# Performance Profiles
-- Powersave
-- Balanced
-- Performance (Kernel Default)
-- Performance Plus (Gaming / OC) (Adjustable CPU / GPU Freq)
# RAM
-- Memory Management
Swap / zRam* - LZ4 compressed swap block-device in RAM - Choice: 0 - 100 % of RAM size
Adjust Swappiness, page-cluster and read_ahead_kb.
Ability to drop caches / buffers, to free RAM.
* For multitasking, gaming, responsiveness and battery life.
# Network
Load kernel module for network file systems
SMB2/SMB3 / CIFS
NFS v2, v3 & v4
L2TP - used for VPN.
Wireguard - Secure Network Tunnel.
TCP Congestion Control - Choice: cubic, new reno, bic, westwood+, vegas, veno, hybla, etc..
Wi-Fi Band Selection, choice: "2.4 GHz / 5 GHz", "2.4 GHz only" or "5 GHz only".
# Misc
-- Torchlight Tuning
Increase brightness for the highest level in Android quick settings. - Range: 10 - 17 - Default Max is "10"
-- LED-RGB
Set blink ON / OFF delay for notifications / low battery.
Optimize RED, GREEN, BLUE LED - Increases brightness by disabling powersave mode on low lux.
-- Accelerometer Calibration
# File Systems
-- Load kernel module for NTFS.
# Advanced Power Menu
Reboot to:
-- system
-- recovery
-- download
or:
-- shutdown
- Settings --> Phone Info --> Software info --> build number (tap 7 times)
- Tap 2 times the back-key
- Developer settings --> enable "OEM unlock"
- Download TWRP for S8 / S8+ / Note8 accordingly (the .tar version, for ODIN flash over PC)
- Download latest A2N Kernel for S8 / S8+ / Note8 accordingly and put the file in USB-thumb or in micro-sd-card
- Download latest Magisk.apk
- Rename Magisk.apk to Magisk.zip and put the file in USB-thumb or in micro-sd-card
- Power off
- Boot in Download-mode
- Flash the .tar twrp file with ODIN (disable "auto-reboot" and "reset time")
- Reboot directly to TWRP
- wipe ---> format data ---> "yes" (type yes) and ENTER.
- Flash latest A2N Kernel
- Flash Magisk.zip
- Optional but recommended: flash AdAway_hosts_patcher_g95x.zip (battery drain fix for vanced YouTube and vanced YT music)
- Reboot to system and enjoy !
- Note: first boot takes around 15 minutes for proper app optimization !
Update A2N Kernel
- Flash Magisk.zip
- Reboot to system and enjoy !
Big thanks @ Mobile Tech Point for making this awesome video !
Note: the video is no longer up-to-date, but it's still a good starting point.
Current Bugs and Changelog
FAQ
Join Telegram Group
Note: the group is not maintained by the kernel developer.
Disclaimer
I am not responsible for anything that happens after flashing the work provided here.
Sharing is caring, so according to the (much unwelcomed) rule 12 you can use my open source on GitHub without my explicit consent or credits. But this is where the caring stops as I do not allow you to use any of my own provided files (except for unmodified stock files). Section 3 of this rule states that you can try to bypass my explicit consent by releasing it as your own when you succeed to make significant changes to the work, otherwise i'll report you and your thread will be removed.
Credits
Linus Torvalds - Linux kernel
Google - Android kernel patches
Samsung - device kernel source
@corsicanu - TWRP recovery - original thread
@S.AMU for providing FTP-Server
000webhost - Webhosting
@Noxxxious for the nice disclaimer text
XDA members - Reporting bugs
Contributors
ace2nutzer
Source Code: https://github.com/ace2nutzer/Samsung_dreamlte_Kernel32Buglist - Kernel V. 2022.07.01
- None so far
Kernel V. 2022.07.01
- DEX: bug fix for 3rd-party HDMI adapters
- DVFS table: removed hardcoded OV for big CPU by me
- Reduced power consumption for IDLE + low Freq steps (especially for Note8)
- UHQ Audio: exported pm_qos_lit to userspace (to fix audio scratching)
A2N Kernel Control V. 5.0
- Audio: added UHQ pm_qos_lit control (to fix audio scratching)
Kernel V. 2022.06.24
- Charger Control: fixed bugs in LPM and battery IDLE feature
- CPU/GPU/RAM/etc...: added voltage control
- CPU/GPU: improved OC stability (CPU lit works stable @ 2 GHz for me)
- Sound: updated pm_qos - should reduce sound scratching while idle and screen off
- GPU: added voltage control for OC steps (stable up to 839 MHz)
- CPU: added "little only" (for powersave)
- updated defaults
17FAQ
Q: With which ROMs this Kernel is 100 % Compatible ?
A: Currently only with Android 9 custom ROMs, but Samsung stock ROM is recommended.
Q: Is this Kernel 100 % Safe ?
A: Yes.
Q: Will this Kernel Overheat the Phone if I use Highest Settings ?
A: No, you can't do anything wrong. Your phone has hard- and software overheat protection.
Q: How to Revert all Changes Made by this Kernel ?
A: Flash latest 3-parted stock ROM with ODIN or flash the Samsung kernel from my download site.
Q: How to bypass SafetyNet ?
A: Anable MagiskHide in Magisk app.
Q: How i can Tune this Kernel ??
A: Everytime you install or update this kernel you will face an red (demo) app "A2N Kernel Control..." open this app, and it'll redirect you to Google Play to get the full version (blue app).
Q: Can i use and Tune your Kernel with other Kernel Manager Apps ?
A: Yes, but you need first to unlock kernel with the A2N app full version.
Q: I've Installed the Full Version of the App, Will it Change any Kernel Settings by Default if i do not Change them ?
A: No, default app settings = default kernel settings.
Q: I've the Full Version of the A2N Kernel Control App, Do i still need the Demo Version of the App ?
A: Yes, there are some special features in-app-menu like "Fake Enforce" and debugging features for easy bug reports.
Q: How to Charge from 10 % to 100 % In just 1 h ?
A: E.g. set "AC Current Max" and "Maximum Charging Temperature" to the Max.
Q: How to get Max Speed for e.g. Highest FPS in Games ?
A: Set BIG / LITTLE CPU and GPU Freq to the Max, but avoid to use "unsafe" Freq's.
Then set CPU / GPU --> DVFS --> "Maximum Temperature" to the Max.
Now you can even cook an egg on your phone !
Q: Will my Custom A2N Settings Survive if i install Stock Kernel and then going back to A2N Kernel ?
A: Yes, as long as you don't uninstall it.
Q: Can i use your Kernel Control App with other Custom Kernels ?
A: No, it's not universal kernel manager app.
Q: My A2N App is Crashing after an Update, how to fix it ?
A: Re-install it. If it doesn't help, wipe dalvik-cache in recovery.
Q: My A2N App shows: "Please check your internet connection" - But i've good internet connection. - How to fix it ?
A: Settings --> network settings --> use private DNS server like "dns.adguard.com" - confirmed to work by user @Arnz09 - see his post here.
Otherwise send me a pm with the screenshot and you current location (city)
Q: Why I get lower benchmark scores with this kernel compared with the Samsung kernel ?
A: This kernel uses by default Max CPU/GPU DVFS Temp 65 °C to reduce the device heat. You can buy the full version of the A2N app to set the DVFS Temp up to 100 °C to get higher scores than on stock kernel.
Q: Why the Android Battery setting "fast charging" has no effect on this kernel ? - It charges always with around 1500 mA.
A: Because it would conflict with the built-in charger control.
The default charging current of approx. 1500 mA means no fast charging by default, even if you actually see "fast charging" in the notification section. This is also useful to reduce battery stress and device heat. To charge even with higher speed/current than on stock kernel you need to buy the full version of the A2N app.
Q: Why I've to pay money for just changing kernel settings ?
A: Well quality has its price. Also nobody forces you to use this kernel.
You can flash other custom kernels or flash the Samsung stock kernel from my download site. Good luck !
Q: When we get an update ?
A: This kernel is almost 100 % stable and works very well. Also this phone is now a bit "old" and therefore don't expect frequent updates.
Also don't ask for ETA's and if you do anyway, I'll ignore.
Q: How to fix audio stutering ?
A: Increase the UHQ PM-QOS-LIT Freq in A2N app in "Audio" section.
If you don't have the full version, you can run a cmd like this:
Q: What is the benefit of editing the voltage table ?
A: to increase OC stability increase voltage and to decrease the device heat, decrease voltage. Last one will improve performance due to less throttling ! So it depends on your needs.
Q: How much is safe to undervolt ?
A: approx -50 or -75 mV is considered to be "safe".
Q: How to edit voltage table ?
A: First of all: to set different CPU/GPU clocks or voltages you need to have Magisk installed and buy my A2N kernel control app full version. This will unlock all premium features of this kernel.
To edit GPU voltages for steps > 572 MHz ---> use the A2N app full version.
To change all the other voltages, you need to use ADB and later once you have found the proper voltages for your phone then you can write them to a script that will be executed at every boot.
Note: this voltage table is from my phone. Your phone may have a different table, so please use your table when it comes to calculate how much you want to undervolt. (50 - 75 mV or 50000 - 75000 uV should be safe)
I'll help you, here we go !
Q: How to Report Bugs ?
- Please DO NOT report bugs if you are:
--- using "unsafe" Freqs
--- not using the latest release !
--- not using Samsung stock ROM (based stock ROMs are custom ROMs !)
A: Open the red A2N Kernel Control demo app and check in-app-menu (3 dots) then "Debug" and then on "logcat and dmesg" if you faced an app crash or if some features didn't work.
If the phone rebooted randomly, then tap on "last_kmsg". You will find the logs in your internal storage. After that you can attach them here in your bug report, by clicking "Attach files".
ROM:
Kernel version:
A2N app version:
BUG:
How to reproduce:
Same bug with stock kernel ? : YES / NO
Download stock kernel for bug reference: S8 / S8+ / Note8
BUG REPORTS THAT DO NOT FOLLOW THESE RULES WILL BE IGNORED !!!12Hello dear Friends i'm back with a great Changelog ...
Kernel 20191019
- FULL Android 9 Pie Support
- Based on Stock Source Code DSI1
- Ramdisk DSI1
- Compiled with the OFFICIAL ARM/Linaro GCC 8.3
- Optimized Memory Managent
- Improved Performance
- Improved Battery Life
- Reduced Device heat
- More Responsive
- Fixed Laggs (especially for some 2D Games)
- Increased Efficiency
- RAM: 3485 @ 3711 MB
- Unlocked higher CPU/GPU Freq Steps - Thanks @Noxxxious
- SELinux in permissive mode - Thanks @Noxxxious
- Disabled SSWAP
- Added zRam Support with fast LZ4 Compressor
- Added KSM Support - patched for Android by me
- Optimized Input Booster
- Fixed very bad CPU IDLE
- CPU: Interactive @ conservative gov - for higher efficiency
- Added Wireguard Support
- CPU: Cluster 0: Screen ON min_freq 455 @ 715 MHz to Fix Lags - 455 MHz Step is used for Screen OFF
- Compiled with DEFAULT_USE_ENERGY_AWARE / WQ_POWER_EFFICIENT_DEFAULT - for better Battery Lifetime
- Optimized Crypto, NEON SIMD Hardware Acceleration (e.g. faster device encryption due of hardware acceleration)
- Disabled HMP since it serves nothing - Hardware doesn't allow to use real cpu_hotplugging ...
- Added Charger Control 2.0 by me - Allows to configure custom max input current from 100 - 3000 mA in 100 mA Steps separately for AC / USB 2.0 / USB 3.0 / Wireless - that means real Fast Charging even with Screen ON - Allows even to charge at max current possible with 3rd-party Chargers !!
- Added Flashlight Torch Control - You can adjust Brightness of your Torch from 1 - 15 - Default/Stock Kernel is just 5
- SELinux: Removed Audit dependency - Thanks @ kerneltoast && arter97
- Added Support for F2FS
- Accurate remaining time to full charged battery
- init.d Support
- And many more Kernel Tweaks - i can't list them all here ... changelog is already too long isn't it ?! :laugh:
A2N Kernel Control V1.4
- The best Way to manage this Kernel for full functionality (3rd-party Kernel Manager Apps will not work properly with this Kernel)
- Compiled with API 28 Android 9 Pie
- Power: Charger Control - Allows to configure custom max input current from 100 - 3000 mA in 100 mA Steps separately for AC / USB 2.0 / USB 3.0 / Wireless - that means real Fast Charging even with Screen ON - Allows even to charge at max current possible with 3rd-party Chargers !!
- Added switch for "Adaptive Fast Charging" so u can directly toggle AFC in the App.
- Ability to check actual accepted charging current and Input Voltage
- CPU: OC Control: Cluster 0: up to 2002 MHz and Cluster 1: up to 2808 MHz
- CPU Governor tuning: Adjust up_threshold to balance between Battery Lifetime and Performance separately for each Cluster
- GPU: OC Control up to 839 MHz
- Hardcoded Performance Profiles:
- --> Powersave (Underclocked)
- --> Balanced (Kernel Default)
- --> Performance (Overclocked)
- Misc: switch for zRam, KSM
- Misc: Torch Brightness Control - up to 3 times brighter flashlight than with a stock Kernel !!
- Misc: Ability to load kernel Module for CIFS and NFS with just one Tap
- Misc: Accelerometer Calibration
- Debug: u can call this Menu over the App built-in Menu (3 dot) - ability to save logcat and dmesg with one tap to your sdcard ..
If u've any Questions, feel free to ask here.
Enjoy your new A2N Kernel !10New Build is Up !!
Changelog
Kernel 20200519
- Source Update DTA6 -> DTC6
- Charger Control: allowed higher chg_temp - should charger faster, especially for 3000+ mA
- defconfigs: re-enable Gear VR related drivers
--------------------------------------------------------------------------------
Updated also TWRP Kernel.
