Search This thread

Stephen

Senior Moderator / Moderator Committee Ban Time!
Staff member
  • Jul 14, 2010
    15,061
    17,804
    41
    Northern Ireland
    OnePlus 8T
    I have headaches when I read such an abomination of a bug report. Please fix it.
    Hitting the guys phone very hard with a hammer will not only fix his phone but help your headache at the same time!!!!

    EDIT: Please dont try this I was only joking! It will brick your phone :)
     

    mziel

    Senior Member
    Aug 13, 2010
    78
    14
    Płock
    No wlan0 interface

    I hope there won't be any headaches with this one:

    After trying some other kernels and reverting back to bricked 1.4 I ended up with dead wifi... It was running ok before reverting. I'm not saying that Bricked bricked it ;) but after the installation wifi was gone :( With previous kernel (not bricked) I did some undervolting (-12.5 V) and OC (standard 1720 or something like that) but wifi was there.

    Now there is no wlan0 interface, grepping WLAN in dmesg shows:

    Code:
    Viper [email protected]/# dmesg | grep WLAN                                                 
    <6>[    3.600646] [WLAN] ## wifi_probe
    <4>[    3.600769] [WLAN][WRN] wifi_set_power = 1
    <6>[    3.722290] [WLAN] wifi_set_carddetect = 1
    <6>[    3.722869] [WLAN] Dongle Host Driver, version 5.90.125.120
    <6>[    3.778198] [WLAN] alloc static buf at cf980000!
    <4>[    5.792053] [WLAN][WRN] dhdsdio_probe_attach: si_attach failed!
    <4>[    5.792572] [WLAN][WRN] dhdsdio_probe: dhdsdio_probe_attach failed
    <4>[    5.793640] [WLAN][WRN] dhd_module_init: wifi_fail_retry is true
    <6>[    5.795104] [WLAN] ## wifi_remove
    <4>[    5.796020] [WLAN][WRN] wifi_set_power = 0
    <6>[    5.920776] [WLAN] wifi_set_carddetect = 0
    <6>[    5.921173] [WLAN] ## wifi_remove leave
    <6>[    5.921386] [WLAN] module init fail, try again!
    <6>[    6.043792] [WLAN] Dongle Host Driver, version 5.90.125.120

    and logcat:
    Code:
    I/wpa_supplicant( 4629): rfkill: Cannot open RFKILL control device
    E/wpa_supplicant( 4629): Could not read interface wlan0 flags: No such device
    (...)
    E/wpa_supplicant( 4629): Could not read interface wlan0 flags: No such device
    E/wpa_supplicant( 4629): nl80211: Could not set interface 'wlan0' UP
    E/wpa_supplicant( 4629): wlan0: Failed to initialize driver interface

    I have S-OFF, ViperS 1.1.0, Radio_11.76A.3504.00P_11.24A.3504.31_M and
    HTC-RIL_4.0.0037HMQ.

    I have tried WiFix ;)
    Is there anything that could help? Thanx.
     

    Berky99

    Senior Member
    Dec 2, 2010
    54
    5
    I just wondered if there's any chance of adding one-click GPS-on/off (i.e. via a widget such as one built using the Widgesoid)? Currently, using any widget to switch the GPS status instead takes me to the phone's GPS settings page. A ROM I had for my previous phone (HTC Desire HD) had this functionality and it saves some time. Many thanks for reading.
     

    Yank555

    Senior Member
    Sep 18, 2009
    8,716
    19,947
    I just wondered if there's any chance of adding one-click GPS-on/off (i.e. via a widget such as one built using the Widgesoid)? Currently, using any widget to switch the GPS status instead takes me to the phone's GPS settings page. A ROM I had for my previous phone (HTC Desire HD) had this functionality and it saves some time. Many thanks for reading.

    Wrong thread ? This is a kernel thread, not a ROM thread...
     

    vali_p33

    Senior Member
    Jan 4, 2008
    101
    7
    I just wondered if there's any chance of adding one-click GPS-on/off (i.e. via a widget such as one built using the Widgesoid)? Currently, using any widget to switch the GPS status instead takes me to the phone's GPS settings page. A ROM I had for my previous phone (HTC Desire HD) had this functionality and it saves some time. Many thanks for reading.

    Try Elixir widget in google play, or HTC widgets.
    Not related to kernel

    Sent from my HTC Sensation XE with Beats Audio
     

    guidogsbn

    Senior Member
    Feb 7, 2010
    1,706
    1,173
    67
    Bonn, Germany

    X46X

    Senior Member
    Apr 9, 2008
    1,145
    90
    Prague
    Hi, I trying this kernel but when when phone booting and you see "andoid update aplication" it stuck and reboot and there starts a bootloap from "white HTC screen"

    EDIT: After ROM Re-Flash it be ok..
     
    Last edited:

    Berky99

    Senior Member
    Dec 2, 2010
    54
    5
    I just wondered if there's any chance of adding one-click GPS-on/off (i.e. via a widget such as one built using the Widgesoid)? Currently, using any widget to switch the GPS status instead takes me to the phone's GPS settings page. A ROM I had for my previous phone (HTC Desire HD) had this functionality and it saves some time. Many thanks for reading.

    Try Elixir widget in google play, or HTC widgets.
    Not related to kernel

    Wrong thread ? This is a kernel thread, not a ROM thread...


    Thanks both for your replies and sorry. I thought it was a kernel issue and in fact it may be for all I know, since it's a function Google stopped from Android 4.0+ for security. Any standard one-click widget GPS widget, whether pre-made or made using a widget-making app DOES NOT work - it'll just take you to the GPS settings page so you can confirm..

    I've learned there may be ways to do it and will have to research further. Thanks again.
     

    vali_p33

    Senior Member
    Jan 4, 2008
    101
    7
    Thanks both for your replies and sorry. I thought it was a kernel issue and in fact it may be for all I know, since it's a function Google stopped from Android 4.0+ for security. Any standard one-click widget GPS widget, whether pre-made or made using a widget-making app DOES NOT work - it'll just take you to the GPS settings page so you can confirm..

    I've learned there may be ways to do it and will have to research further. Thanks again.

    you are right about the settings page.
    i use an application called "automate it" - when i start navigation opens gps whithout confirmation. the same when i close navi app, it's stops gps. there are others: tasker, llama.
    sorry for off-topic.
     

    mudhi

    Senior Member
    Jul 7, 2010
    338
    248
    51
    Taiwan
    On Rom. 3.32, v1.31 - no random reboots nor shutdown. V1.4 random reboots.

    On Rom 3.33 and firmware 3.33, v1.31 normal, v1.4 random shutdowns, no random reboots.

    I think voltage related?
     
    Last edited:

    templargfx

    Member
    Mar 27, 2008
    27
    2
    I am running CM9 RC2 and latest GL drivers.

    With this kernel installed (max performance options chosen, no swipe to wake) whenever I try and connect usb storage, it dismounts my SD card.

    Is there a fix for this?
     

    Top Liked Posts

    • There are no posts matching your filters.
    • 823



      SENSE Bricked-Kernel-3.0 Sensation (pyramid)

      The first kernel with kernel mpdecision & 3-phase kernel thermal control
      no need for those binaries anymore :p


      Highlights:

      Default clocks: 1566Mhz max / 192Mhz min
      OverClockable till 1944Mhz !NOT ALL DEVICES CAN HANDLE THIS!
      3D GPU Overclock @ 320Mhz (if selected during install)
      2D GPU Overclock @ 266.667Mhz (if selected during install)
      5 Stages 3D GPU scaling, variable io_fraction
      3 Stages 2D GPU scaling, io_fraction 100
      Increased bus bandwidth
      L2 Performance Boost
      cmdline options!
      maximum screen off frequency
      (configurable through cmdline options)
      Sweep2Wake! (if selected during install)
      >badass governor<
      3-phase kernel cpu thermal control
      >100% kernel based mpdecision<
      The first kernel with interactive install using Aroma Installer by amarullz
      with more customizations than you can dream of on any other kernel!


      Features:

      Code:
      [U]* CM (AOSP) compatible version: See below![/U]
      * 3.0.36
      * based on HTCs-3.0.16-Sources
      * Tested with Sense 3.6 ICS (no known problems)
      * Tested with Sense 4 ICS (animations work, thx to virtuous)
      * Command Line Options - innovative!
      __ Rename the zip to change your settings!
      * Sweep2Wake
      * badass governor
      * 3-phase kernel cpu thermal control
      * 100% kernel based mpdecision
      * Optimized
      * Built with highest Optimization Level (O3)
      * Strongly improved UI-performance
      * KGSL Early Suspend GPU slumber
      * Increased 3D/2D-Performance (GPUOC)
      * CAF Bluetooth stack (newer) - faux123
      * CIFS
      * UTF8 encoding (included for CIFS)
      * wifi pm=fast
      * Tweaked ondemand governor
      * Undervoltage
      * Overclocking to 1566Mhz default
      * Min Clock @ 192Mhz default
      * Boot time optimization. CPU will have 1566Mhz clocks during boot to ensure a fast bootup
      * Flashlight and Camera-Flash will now be useable until battery reaches 5%
      * Tree-based preemptible RCU
      * Fast scheduler for CPU hotplug
      * optimized preemptive settings
      * basic NTFS support
      * Userspace driven configuration filesystem
      * Allow CPU-supported unaligned accesses
      * Global CPU Voltage table used for adjusting voltage table for SnapDragon Dual Core. Inspired by Snq- modified by faux123 for SnapDragon fixed by show-p1984
      * Improved Mobile Connection (fixed possible freezes introduced by HTC)
      * ~8% Undervolted till 1566Mhz
      * L2 Performance Push
      * 3D GPU Overclock @ 320Mhz
      * 2D GPU Overclock @ 266.667Mhz
      * 6 Stages 3D GPU scaling, variable io_fraction
      * 3 Stages 2D GPU scaling, io_fraction 100
      * Tweaked ondemand to raise frequencies with higher load only (should contribute to battery life)
      * Increased writing performance (lowers that annoying lag when updating 2 apps at the same time)
      * Git's Sha1 implementation significantly decreases boot time
      * CRC-optimizations
      * ZRAM
      * Fudgeswap 
      * PPP over standard asynchronous serial ports
      * PPP over synchronous (HDLC) tty devices
      * [URL="http://dl.dropbox.com/u/44206202/CallRecorder_v.1.0.20_alpha_2.apk"]Two-Way-Call-Recording[/URL]
      * basic NTFS support
      * increased bus frequency
      * Improved WIFI - WLAN detection
      * Automatic process group scheduling
      * Lowered wifi-voltage
      * cleaned code, improved performance
      * Dropped debug code, was slowing things down

      Changelog @ bricked.dehttp://bricked.de/compat.php?action=changelogs&device=pyramid&type=sense


      What is sweep2wake?


      Since this function collides with HTC's screenshot function (PWR+HOME) it will be disabled. Use the AOSP screenshot instead. (PWR+VOL.DOWN at the same time and hold it for about a sec)
      This has a few advantages, one is a nice animation ;) the second would be that it is hardcoded by google into any ICS firmware you can find. That means: no matter which device you will pick up, as long as it has ICS this function should work out of the box.

      How to change your frequency/governor before flashing?

      That's new. Sounds strange, but it works. I am proud to present a truly innovative concept:
      cmdline_khz / cmdline_gov / cmdline_maxscroff
      What does this do for you?

      Have you ever wished you could set the default min/max/gov/scroff frequency on your own?
      Without having to rely on the dev to recompile?
      Or doing it yourself?
      Or even bothering to learn how to do that?
      Or using OC apps that are just in the way?

      (governor set able in setup from version 1.0)

      Well, your prayers have been heard!

      It simplifies any kernel install to the bare minimum. You download the zip, and just change the values to your liking. The kernel will obey you, it's magic!
      you will download this file for example:
      Bricked-3.0-v0.61-ics-maxkhz=1566000-minkhz=192000-maxscroff=432000.zip
      now it is possible that you don't want to oc to 1566Mhz, or your preferred min freq is higher, or or or...
      Just rename the file!
      Bricked-3.0-v0.61-ics-maxkhz=1188000-minkhz=384000-maxscroff=540000.zip
      The kernel will now boot from second 0 with this settings:
      Max freq: 1188Mhz
      Min freq: 384Mhz
      maxscroff: 540Mhz
      Cool, isn't it?

      Now one could say, hell that's too dangerous, what if I write something wrong in there? No problem, your show-p1984 thought of everything. I have built in that much security measures that it is not even remotely imaginable that something could go wrong. I am serious. Whoever manages to break it gets a golden pile of **** from me.
      Now what does it "autocorrect" exactly?
      It corrects mhz instead of khz values for you, so you can actually flash this:
      Code:
      Bricked-3.0-v0.61-ics-maxkhz=1188-minkhz=384-maxscroff=540.zip
      and it will still work.
      Or it corrects wrong acpu frequencies. You can find a table @ the second post, but if you mistype sth, no fear, it will still work!
      Code:
      Bricked-3.0-v0.61-ics-maxkhz=1190-minkhz=390-maxscroff=545.zip
      for example will let the kernel boot with 1188Mhz max and 384Mhz min (maximum screen off frequency 540Mhz). It always falls back to the next lower step. Actually you won't need to bother for the acpu table anymore, just type anything in there, it will automatically correct it for you! If you still want to enter the correct values, just look in the second post ;)
      Now what if you write a letter in there? Like this:
      Code:
      Bricked-3.0-v0.61-ics-maxkhz=II88000-minkhz=38A000-maxscroff=5A0O00.zip
      Well, the kernel will detect that and fall back to default settings read out of my .config. Which means the kernel will boot @ 1566Mhz max and 192Mhz min and maxscroff will be set to 1566Mhz (=disabled).

      What to do if you just want to change your clocks?
      Rename the zip file, boot into recovery, flash, and enjoy ;)
      There is also a sysfs interface for the maxscroff frequency, for simplicity I kept the common name for it.
      /sys/devices/system/cpu/cpu0/cpufreq/screen_off_max_freq

      Currently there is only one limitation:
      You can't have two files with the same base on your scard. that means:
      Code:
      Bricked-3.0-v0.61-ics-maxkhz=1566000-minkhz=192000-maxscroff=432000.zip
      Bricked-3.0-v0.61-ics-maxkhz=1188000-minkhz=384000-maxscroff=540000.zip
      are not allowed to be on the sdcard at the same time, the kernel would boot with defaults: 1566/192 if you flash either one of those files.
      The "base" of the filename is this: Bricked-3.0-v0.61-ics-
      So you can have 2 files (or more) on the sdcard with names like this:
      Bricked-3.0-v0.55-b4-ics-****
      Bricked-3.0-v0.7-ics-****
      Bricked-3.0-v0.8-ics-****
      (****=etc etc etc etc)
      Furthermore it must be followed by maxkhz=VALUE-minkhz=VALUE-maxscroff=VALUE.zip It is not possible to switch the positions of the options. But you can leave them out of there completely, the kernel will then boot with 1566/192/1566.


      Ah btw: We now see our set max mhz under Settings->About Phone->HW->Cpu ;) (it actually changes when you change your maxkhz)

      This is genuine innovative code from me. I didn't even occasional glance at someone elses work. So if sth like this is already out there, SCREW THE DEV :p because I did not see it and wrote it from scratch! :D

      And since 0.6 comes with the awesome Aroma installer you can now choose from 3 gpuoc versions!
      GPU OC disabled, [email protected] & [email protected]
      GPU low overclock, [email protected] & [email protected]
      GPU high overclock, [email protected] & [email protected] + Bandwidth push


      The source for this is split into two parts, Kernel & bash script. The script finds the zip on your sdcard, parses the filename and modifies the kernels cmdline inside the boot.img. The Kernel is parsing the cmdline, checking if everything is valid and setting your options.

      How to install?

      Just flash from recovery. Because it creates a boot.img out of the one on your phone while flashing, it should work with the majority of ROMs out there.
      Interactive install, enjoy the ride! ;)

      Where to complain about errors/bugs?

      Please use the Issuetracker for bugs/errors/feature wishes!
      Issuetracker @ https://code.google.com/p/bricked/issues/entry

      [email protected]
      IRC Chat: Freenode IRC #bricked

      Download:

      No Guarantees! If it kills your grandmother or your device, I am NOT responsible! If you understand this:
      (If you download, please hit Thanks below my post! Thank you!)


      >>> DOWNLOAD <<<

      XDA Discussion/Download for AOSP (ICS): Click me

      Old Downloads (gcode): Click Me




      Use System Tuner to undervolt!
      Setting min/max frequencies should be done over the zips name instead.




      Source:



      209
      Changelog moved to bricked.dehttp://bricked.de/index.php?action=changelogs&device=pyramid&type=sense

      What does PREEMPTIBLE mean?

      Preemptive built kernels are favoring the userinterface over everything else! That means: An app in the background is using 50% of you CPU to spy on you. You want to move fast through the user interface/watch a video, whatever. The kernel will now favor your action over the app in the background. That's all the magic that's happening ;)
      What is badass?

      Well good question. With ICS I decided to rework my gb badass which never got released because it was always pushed aside. To break down what it is:

      Badass removes all of this "fast peaking" to the max frequency. On a typical system the cpu won't go above 918Mhz and therefore stay cool and will use less power. To trigger a frequency increase, the system must run a bit @ 918Mhz with high load, then the frequency is bumped to 1188Mhz. If that is still not enough the governor gives you full throttle. (this transition should not take longer than 1-2 seconds, depending on the load your system is experiencing)
      Badass will also take the gpu load into consideration. If the gpu is moderately busy it will bypass the above check and clock the cpu with 1188Mhz. If the gpu is crushed under load, badass will lift the restrictions to the cpu.

      Please remember: Due to it's nature, this is not a benchmark governor. It is meant as a governor that gives you a smooth experience while saving battery, lots of it ;)
      What is msm_thermal?

      Kernel based 3-phase thermal control!
      This replaces your /system/bin/thermald binary which is renamed by the installer to thermald_backup.

      Check /sys/kernel/msm_thermal/conf/ for the thermal configuration :)

      allowed_max_high = highest threshold (phase 3)
      allowed_max_low = remove the throttling if we cooled down to this (clr_thrshold)
      allowed_max_freq = max frequency if throttled (limit)

      [...]mid[...] = same as above, just for phase 2
      [...]low[...] = Lowest threshold (phase 1)

      check_interval_ms = how often shall we check? (sampling rate)
      Default: 1000ms (=1sec)

      If you want to see msm_thermal doing it's job:
      Code:
      adb shell
      cat /proc/kmsg | grep 'msm_thermal'
      What is msm_mpdecision?

      100% kernel based multi core decision! (should cpu1 be online or not?)
      This replaces your /system/bin/mpdecision binary which is renamed by the installer to mpdecision_backup.

      Check /sys/kernel/msm_mpdecision/conf/ for the configuration.

      startdelay = time until mpdecision starts doing it's magic (70000)
      delay = time between checks (500)
      pause = if something else plugs in the cpu, fall asleep for 10000
      scroff_single_core = if the screen is off, don't plug in cpu1 (1)
      nwns_threshold_up = runqueue threshold, if this is reached cpu1 will be hotplugged (35)
      nwns_threshold_down = runqueue threshold, if this is reached cpu1 will be unplugged (5)
      twts_threshold_up = time threshold, this amount of time must have passed (250)
      twts_threshold_down = same as above (250)
      enabled = enable(1) or disable(0) mpdecision. This does not affect scroff_single_core!
      idle_freq = a value against that will be checked if a core +/- is requested. (486000)
      If cpu0 is below that value and a core up of cpu1 is requested, nothing will happen.
      If cpu1 is above that value and a core down of cpu1 is requested, nothing will happen. (otherwise it would now put down cpu1 even though it is still working)


      (all times are in ms)

      If you want to see the mpdecision magic happening:
      Code:
      adb shell
      cat /proc/kmsg | grep 'MPDEC'



      Frequency/Voltage Table:

      192000: 800000
      310500: 825000
      384000: 825000
      432000: 850000
      486000: 850000
      540000: 875000
      594000: 875000
      648000: 900000
      702000: 900000
      756000: 925000
      810000: 950000
      864000: 975000
      918000: 975000
      972000: 1000000
      1026000: 1000000
      1080000: 1025000
      1134000: 1025000
      1188000: 1050000
      1242000: 1075000
      1296000: 1100000
      1350000: 1125000
      1404000: 1150000
      1458000: 1150000
      1512000: 1175000
      1566000: 1175000
      1620000: 1200000
      1674000: 1225000
      1728000: 1250000
      1782000: 1275000
      1836000: 1300000
      1890000: 1325000
      1944000: 1350000
      Available CPU governors:
      badass <-- !recommended!
      lazy
      interactive
      lagfree
      conservative
      userspace
      powersave
      ondemand
      performance​


      Stock Kernel for ICS. Unsecured boot.img.
      40


      New beta: v0.955
      3 new changes ;)
      -Bluetooth Caf backport from faux123
      -Badass governor
      -allow lower min. brightness (display)


      What is badass?
      Well good question. With ICS I decided to rework my gb badass which never got released because it was always pushed aside. To break down what it is:

      Badass removes all of this "fast peaking" to the max frequency. On a typical system the cpu won't go above 918Mhz and therefore stay cool and will use less power. To trigger a frequency increase, the system must run a bit @ 918Mhz with high load, then the frequency is bumped to 1188Mhz. If that is still not enough the governor gives you full throttle. (this transition should not take longer than 2-5 seconds, depending on the load your system is experiencing)
      Badass will also take the gpu load into consideration. If the gpu is moderately busy it will bypass the above check and clock the cpu with 1188Mhz. If the gpu is crushed under load, badass will lift the restrictions to the cpu.

      This is work in progress. I spent the past 6 hours trying to find sweetspots for the configuration and I think I nailed it in this version ;) (finally... :rolleyes:)

      Please remember: Due to it's nature, this is not a benchmark governor. It is meant as a governor that gives you a smooth experience while saving battery, lots of it ;)

      After that long text, here is the download:

      Download: Click me

      This is the perfect place to hide an ad, therefore:
      HTC One X - Piggy bank!
      Your support is highly appreciated!
      http://bricked.de/

      If you can't donate anything, no problem. Just click on the ad instead ;)
      If you won't click on the ad, my kernel will turn your device into a decepticon that will crawl up your nose when you sleep! NO KIDDING! CLICK THAT AD! :D

      38
      New beta in town with loads of caf changes ;)
      Also patched in thermal stuff in preparation of kernel thermal control, but not yet used because I am still trying to figure out if we can use mpdecision without thermald. I would not like to ditch mpdecision, it provides way better battery life than any other solution I have yet seen. (that's not a dislike on anyone's accomplishments, just a fact ;) )
      + merged linux kernel with upstream 3.0.26...
      Details below.

      Bricked-3.0-v0.55-b2: Click me

      Changelog: (from 0.5)
      Code:
      * 5ca5935 : config: enable bfp jit
      * b637217 : include: linux: filter.h: fix missing rcupdate.h include
      * 3169240 : config: increase usb gadget vbus draw to 500
      * 2b4b3ee : config: enable usb otg wakelocks
      * c353183 : config: update with autogen
      * 57cc678 : msm: kgsl: Add supporting code for 2d dcvs
      * dc16b34 : Linux 3.0.26
      * 8090c01 : powerpc/pmac: Fix SMP kernels on pre-core99 UP machines
      * c8c6786 : iwl3945: fix possible il->txq NULL pointer dereference in delayed works
      * 9284e42 : ipv6: Don't dev_hold(dev) in ip6_mc_find_dev_rcu.
      * dedb848 : tcp: fix syncookie regression
      * 342c078 : perf tools: Incorrect use of snprintf results in SEGV
      * 7d99642 : afs: Remote abort can cause BUG in rxrpc code
      * 615567b : afs: Read of file returns EBADMSG
      * ab12e43 : nilfs2: fix NULL pointer dereference in nilfs_load_super_block()
      * 7d1f547 : thermal: msm8960_tsens: Read TSENS temperature
      * a881ee2 : thermal: tsens: Add tsens notify callback
      * ff4f3ef : thermal: msm8960_tsens: Fix reading the correct sensor4 address
      * fe918d1 : tsens: msm8960: Split write ordering for TSENS Enable
      * c9b0c6b : thermal: tsens8960: Fix setting initial return value
      * 617c974 : thermal: tsens: Use Calibration offset data from QFPROM
      * 0ba824a : thermal: tsens: Add support for MDM9615
      * 7851012 : thermal: msm8960: Check for SOC version
      * d3dc239 : thermal: tsens: Add platform information for 9615
      * 009b0a6 : thermal: msm: Update TSENS for 8960_V2
      * 14caa18 : drivers/usb/misc: add ehset.c for OTG operations
      * be703bc : [PATCH] usb: otg: Temporarily grab wakelock on charger and  disconnect events
      * 9ad0728 : USB: OTG: Take wakelock when VBUS present
      * 62d713c : msm: msm_xo: Set the correct bits for XO_CORE on 8660
      * c3407bb : msm: pm-8x60: Add clock debug to idle code path.
      * 1eaa81f : msm: pm-8x60: Move hotplug related code out of pm code.
      * c30553e : msm: hotplug: Support cpu hotplug in no PM cases
      * f971d96 : msm: cpufreq: Check cpufreq_frequency_table NULL
      * 7e0094c : cpufreq: interactive governor: default 20ms timer
      * e32e728 : power: cpufreq interactive governor: use default sample time 20ms
      * 848c5bc : cpufreq: interactive governor: default timer 10ms, maxspeed load 95%
      * b0b34e3 : cpufreq: interactive: fix possible Division by zero.
      * 727a7b8 : cpufreq : Fix crash input event handler on governor switch
      * 81fcdd8 : msm_thermal: Remove error messages from log when core is offline
      * 3dccf0f : thermal: Fix hotplug race condition leading to memory corruption.
      * 4159bfc : msm: thermal: Add MSM thermal sensing and limiting
      * 253b0eb : scheduler: minor improvement to pick_next_highest_task_rt
      * 1480dc6 : mmc: msm_sdcc: Power down slots after reboot
      * 2958104 : hdmi_msm: Power down PHY register during suspend
      * 93712f7 : cpufreq: Extend ondemand powersave_bias for negative range
      * becdb83 : msm: kgsl: disable irq when adreno device is stopped
      * 7f37a49 : msm: kgsl: convert sg allocation to vmalloc
      * bd08355 : msm: kgsl: Make sure SLUMBER is the requested state
      * 9aa9c5f : msm: kgsl: Clarify the circumstances to enable SLUMBER state
      * e1243e5 : msm: kgsl: Be explicit about what states may access hw
      * 8a47885 : msm: Config option to enable idle stats device
      * ea61106 : msm: kgsl: only poke once during adreno_idle
      * 33f99fd : msm: kgsl: Modify only the pending idle timer in ISR.
      * 59c4f2b : msm: kgsl: flush device workqueue before stop
      * 564ff64 : msm: IDLE_TIMER wakes up waiting processes
      * 0459155 : msm: kgsl: Collect a sample only if GPU is active
      * 5da28701 : msm: kgsl: call device->irqctrl from start/stop
      * 2e84670 : msm: kgsl: Power scale policy needs at least three power levels.
      * 02bf9a1 : msm: kgsl: Don't wake core to check if it is idle.
      * 85cf4a8 : msm: kgsl: Move the GPU register lists to a common location
      * 345d6ec : msm: kgsl: Do not ramp to turbo if the screen is off.
      * 754515b : msm: kgsl: add power tracepoints
      * 9ac487b : msm: kgsl: power state cleanup
      * 909af7b : msm: kgsl: Eventually transition to SLUMBER
      * 9d41c04 : msm: kgsl: in postmortem, log powerstate before changing it
      * 52bf797 : msm: kgsl: adreno_isidle shouldn't BUG()
      * 14a8125 : msm: kgsl: fix infinite loop in adreno_find_region()
      * 58ee6d0 : msm: kgsl: Allow device attributes to be re-created
      * e2e92ba : acpu: use config variable here instead of static value
      * cc7fc34 : ARM: net: JIT compiler for packet filters
      * 9be1d23 : Optimized ARM RWSEM algorithm
      * d701b86 : lib/string: use glibc version
      * 14c5661 : lib/memcopy: use glibc version
      * 6a96ee2 : msm: kgsl: correct amount of scaling steps
      * 7dd2dcb : board: increase the rpm regulator constraints
      * 504eff8 : config: update with generated stuff
      * e10f7d8 : base: genlock: Remove genlock_release_lock and associated ioctl
      * f54adc0 : governor: Added CPUfreq governor 'lazy'
      * e41dbc3 : ARM: entry: no need to increase preempt count for IRQ handlers
      * 854481b : sched: Remove unlikely() from ttwu_post_activation
      * 06d9d20 : sched: Remove unlikely() from rt_policy() in sched.c
      * f1e8e4b : sched: Change pick_next_task_rt from unlikely to likely
      * 169384a : sched: Cleanup pre_schedule_rt
      * 9260908 : Add LagFree CPU Governor
      * 1796f64 : sched: disable GENTLTE_FAIR_SLEEPERS for better performance on Android
      * a8f2169 : Make vfs_cache_pressure configurable
      * 9d95e8b : msm: kgsl: add GPUOC config variable
      * 488092e : acpu/avs: push POSSIBLE max voltage, wider scaling range for the user
      * 980ed38 : acpu: slightly push voltages above 1566 to make it more oc happy
      * cc33fb2 : msm: deactivate notification led timeout
      * ba10ae1 : kgsl: eliminate not used scaling steps
      * 8e49ddf : Revert "kgsl: increase max allowed power levels"
      * e86aa21 : kgsl: 2D: increase bandwidth to avoid bottlenecking the gpu
      * 1288640 : kgsl: 3D: increase bandwidth to avoid bottlenecking the gpu
      * 49c0c7a : drivers: input: cy8c_tma_ts: properly fix touchscreen issues. (HTC)

      Support my night-shifts (this time from 20pm-06am ;))! Download and test! ;)
      37
      New beta release,
      Codename: Legends of Awesomeness! ;)



      Bricked-3.0-v0.55-b4-ics
      Click Me, at the bottom of this post so I can be 50% sure you actually read this :p


      What has changed from b3?
      Actually "only" one thing. But that is truly innovative and will make things a lot easier for devs and users. Took me the whole night and I am awake since 19 hours so excuse any typos. My monitor is only one white blur atm :D

      Have you ever wished you could set the default min/max frequency on your own?
      Without having to rely on the dev to recompile?
      Or doing it yourself?
      Or even bothering to learn how to do that?


      Well guys, your prayers have been heard!

      This Beta 4 has the ability to set your default min/max cpuclocks over the zips filename with which you flash it!
      Stop drooling, it's no fake, it works.
      So what the **** do I mean by that?
      Well usually a kernel dev sets one default boot setting, like Bricked's defaults are: 1566/192. Sometimes this is not what you want, so you need to install an OC app, under or over clock, etc. In this case you just edit the zip file, flash, and you are good to go! No need to change anything with an oc app!

      Let me explain this on an example:
      The name of the file you guys download is:
      Code:
      Bricked-3.0-v0.55-b4-ics-maxkhz=1566000-minkhz=192000.zip
      That means the kernel will boot with 1566 Mhz max & 192 Mhz min. Now if you want to change that you just need to edit the zips name, and reflash. Done! Like this:
      Code:
      Bricked-3.0-v0.55-b4-ics-maxkhz=1188000-minkhz=384000.zip
      Now one could say, hell that's too dangerous, what if I write something wrong in there? No problem, your show-p1984 thought of everything. I have built in that much security measures that it is not even remotely imaginable that something could go wrong. I am serious. Whoever manages to break it gets a golden pile of **** from me.
      Now what does it "autocorrect" exactly?
      It corrects mhz instead of khz values for you, so you can actually flash this:
      Code:
      Bricked-3.0-v0.55-b4-ics-maxkhz=1188-minkhz=384.zip
      and it will still work.
      Or it corrects wrong acpu frequencies. You can find a table @ the second post, but if you mistype sth, no fear, it will still work!
      Code:
      Bricked-3.0-v0.55-b4-ics-maxkhz=1190-minkhz=390.zip
      for example will let the kernel boot with 1188Mhz max and 384Mhz min. It always falls back to the next lower step. (Actually you won't need to bother for the acpu table anymore, just type anything in there, it will automatically correct it for you!)

      Now what if you write a letter in there? Like this:
      Code:
      Bricked-3.0-v0.55-b4-ics-maxkhz=II88000-minkhz=38A000.zip
      Well, the kernel will detect that and fall back to default settings read out of my .config. Which means the kernel will boot @ 1566Mhz max and 192Mhz min.

      What to do if you just want to change your clocks?
      Rename the zip file, boot into recovery, flash, and enjoy ;)

      Currently there is only one limitation:
      You can't have two files with the same base on your scard. that means:
      Code:
      Bricked-3.0-v0.55-b4-ics-maxkhz=1190-minkhz=390.zip
      Bricked-3.0-v0.55-b4-ics-maxkhz=1188-minkhz=192.zip
      are not allowed to be on the sdcard at the same time, the kernel would boot with defaults: 1566/192 if you flash either one of those files. (I am too tired to program a check for that right now ^^)
      The "base" of the filename is this: Bricked-3.0-v0.55-b4-ics-
      So you can have 2 files on the sdcard with names like this:
      Bricked-3.0-v0.55-b4-ics-****
      Bricked-3.0-v0.55-b5-ics-****
      Bricked-3.0-v0.6-ics-****
      (****=etc etc etc etc)
      Furthermore it must be followed by maxkhz=VALUE-minkhz=VALUE.zip It is not possible to switch the positions of max and min. But you can leave them out of there completely, the kernel will then boot with 1566/192.

      This is genuine innovative code from me. I didn't even occasional glance at someone elses work. So if sth like this is already out there, SCREW THE DEV :p because I did not see it and wrote it from scratch! :D

      Source is split into two parts, zip and kernel. Kernel will come online with the official release of 0.6 (got some cleanup to do ^^). The zip can be studied by all the bash ppl out there ;)


      Download
      STOCK GPU CLOCKS ([email protected], [email protected]): CLICK ME
      MAX GPU CLOCKS ([email protected], [email protected]): CLICK ME
    Our Apps
    Get our official app!
    The best way to access XDA on your phone
    Nav Gestures
    Add swipe gestures to any Android
    One Handed Mode
    Eases uses one hand with your phone