I just want to ask you, grey liquid is the cooler liquid that you put on normal pc between CPU and heat sink?
you put it on S3 motherboard between CPU and LCD screen?
bye
[Kernel][Stable][CM11.0/CM12.1/CM13.0/CM14.1][i9300] Elite-Boeffla-Kernel
- Thread starter Oebbler1
- Start date
I just want to ask you, grey liquid is the cooler liquid that you put on normal pc between CPU and heat sink?
you put it on S3 motherboard between CPU and LCD screen?
bye
Hi! I'm planning to release my kernel that is based on this kernel.
Yes, it is.
Yes, I do, because the top of the SoC is oriented to the AMOLED display, so there's no other choice for me to apply the cooling liquid.
You are welcome to do this, but please put my username into your credits if you want to publish your kernel.
Do you have any additional mods installed on your S3? Most probably this bug will disappear when you use a fresh system.
Hi guys,
I planned to port my kernel to Android 8, but this is not possible till now, because Android 8 isn't available for the Galaxy S3. As soon as there will be a working build of Android 8 for the S3, I'll try my best to port my kernel.
If anyone of you notices such a build, you may write a PM to me.
I planned to port my kernel to Android 8, but this is not possible till now, because Android 8 isn't available for the Galaxy S3. As soon as there will be a working build of Android 8 for the S3, I'll try my best to port my kernel.
If anyone of you notices such a build, you may write a PM to me.
Hi,
I have just installed Lineage OS, GAPPs, and Magisk, and last Boeffla-kernel; Kernel is wonderful, I have only changed zram options.. I see a lot of improvement, Sorry to know support will end soon for S3
I want to ask about Magisk Hide function that doesn't work, I see magisk log: "proc monitor your kernel doesn't support mount userspace"
How I can check boeffla last stable kernel is 100% working? the notification icon Boeffla-config v2 is in the upper bar (I mean clock, battery...), and when I Open the app, I see for example swap space and zlib space are increased as I want, there is a method to check the mount of userspace?
thanks...
I have just installed Lineage OS, GAPPs, and Magisk, and last Boeffla-kernel; Kernel is wonderful, I have only changed zram options.. I see a lot of improvement, Sorry to know support will end soon for S3
I want to ask about Magisk Hide function that doesn't work, I see magisk log: "proc monitor your kernel doesn't support mount userspace"
How I can check boeffla last stable kernel is 100% working? the notification icon Boeffla-config v2 is in the upper bar (I mean clock, battery...), and when I Open the app, I see for example swap space and zlib space are increased as I want, there is a method to check the mount of userspace?
thanks...
When I find some time I will check this and probably provide a fixed kernel.
As for Magisk Hide function , you can use Koffee kernel that is based on boeffla as well and has mount userspace implemented into his kernel
Koffee kernel?? I didn't know
Now I downloaded it, installed kernel with TWRP and also low-memory, rebooted...and... and.. all works! thanks a lot!
Do you know if the developer will suppoort it with next Lineage OS ROM?
I am glad i helped you! You can ask that in his thread i think
(but for now he is using the latest base kernel for los 14.1 official, based on latest boeffla kernel ).---------- Post added at 01:03 PM ---------- Previous post was at 01:00 PM ----------
That's great news! We are waiting for that
I have checked the kernel log at /proc/kmsg and see always this:
c0 exynos4212_vpll_set_rate: Invalid Clock VPLL Frequency
Does somebody know what it is about?
c0 exynos4212_vpll_set_rate: Invalid Clock VPLL Frequency
Does somebody know what it is about?
Boeffla implemented new fixes and released Beta7.Are you going to compile again?
Yes, but most probably not in the next 2 weeks.
Hi guys,
due to a crash of the BIOS of my computer I won't be able to compile any new versions of my kernel until I have this issue fixed. Please be patient for the next update.
due to a crash of the BIOS of my computer I won't be able to compile any new versions of my kernel until I have this issue fixed. Please be patient for the next update.
MAC80211
Thanks for putting this kernel mod on github.
I know its probably OT but does anyone have kernel soruce patches for CONFIG_MAC80211=m to build correctly, getting past the
Make[1]: *** [scripts/Makefile.build:441: net/mac80211] Error 2 ?
Any recent release of github.com/Oebbler/elite-boeffla-kernel-lineage14.1-i9300 will do.
Thanks for putting this kernel mod on github.
I know its probably OT but does anyone have kernel soruce patches for CONFIG_MAC80211=m to build correctly, getting past the
Make[1]: *** [scripts/Makefile.build:441: net/mac80211] Error 2 ?
Any recent release of github.com/Oebbler/elite-boeffla-kernel-lineage14.1-i9300 will do.
Similar threads
- Locked
- Locked
- Locked
Top Liked Posts
-
There are no posts matching your filters.
-
40Hi guys,
I want to present my kernel for the Samsung Galaxy S3, that allows you to overclock up to 2 GHz. This kernel is based on the official Boeffla kernel for CM14. Although the official Boeffla kernel supports CM14.0 and CM14.1, my kernel supports CM14.1 only, because CM14.0 for the SGS3 isn't supported by the CM team anymore. It may run on CM14.0 as well, but please don't report any errors if you use it with CM14.0 or any other OS than CM14.1.
Feature list:
- Every feature from official Boeffla-Kernel (6.1 final)
- Support for Synapse (partial) and Boeffla Config (fully)
- CPU overclocking up to 2 GHz
- CPU: 100MHz step added to save power
- Faster boot process due to some internal improvements
- 3 new governors added (adaptive, conservative, interactive)
- CPU voltage can be chosen between 600mV and 1600mV
- full F2FS support (backported from Linux 3.19)
- Charging current can be set up to 2.1 Amps
- Battery percentage never reaches 0%, so the phone won't turn off at low battery
- No overcharge anymore due to an internal improvement
- Early suspend adjustable up to 5000ms
- more undervolting profiles for the GPU
- much lower brightness can be set than on stock kernel; the display will be almost black on lowest brightness level (maximum possible brightness stays the same)
- Configurable kernel logger (turning kernel logger off is not stable on CM and LOS)
- compiled using GCC 7.2.1 by Linaro (Thanks to ZaneZam for publishing the kernel-specific GCC-6-code; this works with GCC 7 as well!)
For configuration I recommend Boeffla Config.
You can use your old config you had using the official Boeffla-Kernel, but this may lead to minor problems. So I'd recommend to reset Boeffla Config before you flash my kernel. If you already use my kernel and just upgrading it you can use the old config without any problems.
WARNING!!! Nobody except you can and will be responsible for a damaged or bricked phone due to my kernel. It's very unlikely that my kernel harms your phone, but it's not impossible.
Have fun using my kernel and feel free to ask questions about it!
Source code: Oebbler · GitHub
XDA:DevDB Information
Elite-Boeffla-Kernel, Kernel for the Samsung Galaxy S III I9300
Contributors
Oebbler1
Kernel Special Features: OC up to 2GHz, Support for Boeffla Config, Full F2FS support, Charging current up to 2.1 Amps
Version Information
Status: Stable
Current Stable Version: 6.1.0.2
Stable Release Date: 2018-12-20
Created 2016-12-27
Last Updated 2018-12-2010Changelog (CM14.1 only)
6.0.0.1-beta1
First Release
this kernel includes every feature and bugfix of Boeffla-Kernel 5.1.0.5 (for CM13.0)
Full F2FS support
6.0.0.1-beta2
not published
6.0.0.1-beta3
Sources updated (all changes from CM-Kernel made until 19.12.2016)
Toolchain updated: GCC 6.2.1 Linaro
6.0.0.1-beta4
Sources updated (LineageOS from 05.01.2017)
6.0.0.1-beta5 and 5.3.0.5-F2FS (CM13.0 version)
Sources updated (LineageOS from 10.01.2017)
Busybox updated to 1.26.2 (thanks to Lord Boeffla)
Kernel logger can be controlled again (below Android logger)
6.0.0.1-beta6
Sources updated (LineageOS from 06.02.2017)
UMS and SELinux fixed (SELinux can be controlled again)
6.0.0.1-beta7
Sources updated (LineageOS from 15.02.2017)
Toolchain updated to Linaro 6.3.1
6.0.0.1-beta8
Sources updated (LineageOS from 07.04.2017)
6.0.0.1-beta9
not published
6.0.0.1-beta10 and 5.3.0.7 (CM13.0 version)
fixed charge levels; now they work fine
internal improvements to extend battery life and to avoid overcharge of the battery
6.0.0.1-beta11 and 5.3.0.8 (CM13.0 version)
Sources updated (LineageOS from 04.06.2017; CM14 kernel only)
Display brightness can be set much lower than on stock kernel now (the display will be almost black on lowest brightness level); but maximum possible brightness stays the same
6.0.0.1-beta12
Sources updated (LineageOS from 21.07.2017)
Toolchain updated to Linaro 7.1.1
Busybox updated (version 1.27.1 compiled by Lord Boeffla)
Display brightness slider fixed
Doze mode switch fixed
6.0.0.1
Same as 6.0.0.1-beta12, but better tested
6.0.0.2
Default governor changed to intelliactive
Default I/O scheduler changed to deadline
Fix for Doze mode switch reworked
Busybox updated (version 1.27.2 compiled by Lord Boeffla)
Toolchain updated to Linaro 7.1.1-2
6.0.0.3
not published
6.0.0.4-Synapse
Sources updated (LineageOS from 19.01.2018)
Synapse support added in addition to Boeffla Config support (Synapse apk can be found in /res/synapse after installing this version of Elite-Boeffla-Kernel)
Default governor changed to pegasusq
6.1.0.1-beta5
Default governor changed back to intelliactive
Battery percentage will show 1% instead of 0% iff battery is fully discharged; it is highly recommended to charge the phone immediately when reching 1%!
Added support for mount namespace separation in order to support Magisk Hide
6.1.0.1
not published
6.1.0.2
fixed the LED driver to properly provide the given settings in Boeffla Config and Synapse
fixed some voltages to get a cooler CPU6
I can't definetly say it, but I plan to do so, but please don't ask for ETA's or something else about this until my first build for Android 8.0 is out.
