• Introducing XDA Computing: Discussion zones for Hardware, Software, and more!    Check it out!
  • Fill out your device list and let everyone know which phones you have!    Edit Your Device Inventory

Klyde PX4 | PX5 | PX6 head units with MCU CSN2 | CSN2_D | CSN2_8600_D (Android 8/9/10

Search This thread

feodoros

Member
Oct 20, 2014
12
1
Czy ktoś może mi powiedzieć, czy mogę moje radio aktualizować ? Jeśli tak, która aktualizacja będzie pasować do mojego radia?

AA0495B-A01 ND0294B-A01

PX5
Andr. 8.0.0
Nr.Ko. 201903151040
Wer. ją
4.4.103
MCU CSN2_03202019_103040

Bardzo proszę o pomoc

Czy ktoś może mi powiedzieć, czy mogę moje radio aktualizować ? Jeśli tak, która aktualizacja będzie pasować do mojego radia?

AA0495B-A01 ND0294B-A01

PX5
Andr. 8.0.0
Nr.Ko. 201903151040
Wer. ją
4.4.103
MCU CSN2_03202019_103040

Bardzo proszę o pomoc
Yes Android 10. March 31, 2021 202103310921 read here ....... https: //forum.xda-developers.com/t/klyde-px4-px5-px6-head-units-with-mcu-csn2-csn2_d -csn2_8600_d-android- 8-9-10.3912413 /



Tak Android 10. 31 marca 2021 202103310921 czytaj tutaj ....... https: //forum.xda-developers.com/t/klyde-px4-px5-px6-head-units-with-mcu-csn2-csn2_d-csn2_8600_d-android- 8-9-10.3912413 /
 
Last edited by a moderator:

dnfm

Senior Member
Nov 24, 2009
73
16
I have had. There could be a few reasons:
- weak connection on SMA connector. The antenna has power 3.3V. If SMA is not tighten, antenna doesn't work.
- wrong location of antenna. Sometimes antenna falls down inside the panel and have no chance to detect GPS signal. The best place is near backview mirror.
That's not really how GPS works. It's a digital signal calculated based on known satellite positions and delay in receiving their times. Either it works or it doesn't. A weak antenna connection or poor location won't make it read off by X meters.

It's something in the software; I was hoping someone had a solution/fix/patch for it.
 

abdelmonem

Member
Jan 26, 2009
45
5
Hello ,

Now after testing everything there is one issue with me internet sharing through Bluetooth are not working I have “KD6” Bluetooth module there’s is any solution for this ,if not I’ll order other RF_210 Bluetooth module .


Regard



AED 36.73 | Bluetooth 5.0 Module for Car Multimedia Player PX5 PX6 Androrid System select RF210 type in factory settings
 

FullSky

Senior Member
Mar 4, 2012
68
4
Taranto
hello everyone, I have a px5 navigator with Android 10 and unfortunately the microphone during phone calls does not work perfectly ... I was thinking, the microphone in the photo would be good to solve this problem? thanks 😉
IMG_20210619_115956.jpg
 
Nov 2, 2020
14
0
while updating, android writes - install the terminal program on your startup and run what terminal is it about? ordinary windos? I'm trying to make a bootable SD card in SDDiskTool and what options should I choose Ubgrade firmware or sd boot? but I have some bugs all the time



podczas aktualizacji android pisze
-- zainstaluj program terminala na swoim uruchomieniu i uruchom
o jaki terminal chodzi ?
zwykły windosowy ?
Próbuje zrobić startową kartę SD w SDDiskTool i jakie opcje mam wybrać Ubgrade firmware czy sd boot ? ale mamcały czas jakieś błędy
 
Last edited by a moderator:

feodoros

Member
Oct 20, 2014
12
1
Aktualizujemy Androida 8.0 do 9.0. Instrukcja jest odpowiednia tylko dla GU producenta Klyde z sufiksem CSN2. Pamiętaj, że działasz na własne ryzyko! ❗ Kładziemy drewno opałowe na komputerze ADB Załączony plikDriverAssitant_v4.5.zip (9,36 MB) Styki na płycie głównej zamykamy pęsetą, jak pokazano na obrazku (obrazek w instrukcji poniżej). Płytę główną podłączamy przez USB do komputera. Umieszczamy AndroidTool na komputerze i uzupełnij kopię zapasową z 9 w GU. AndroidTool-p9-190418 Następnie możesz postawić dowolną 9 bez tej procedury. Instrukcja w języku angielskim Załączony plik 8.0 aktualizacja 9.0 instrukcja.zip (2,21 MB)
Upgrade from Android 8 to 9 WITHOUT disassembling. https://4pda.to/forum/index.php?showtopic=928321&st=540#entry87381770
 
Last edited:
Nov 2, 2020
14
0
all OK I installed android 10 March 31, 2021 202 103 310 921 what's the newest CSN2 MCU for that?



wszystko ok
zainstalowałem androida 10
jakie jest do tego najnowsze MCU CSN2 ?
 
Last edited by a moderator:

ngviethoa

Member
Oct 17, 2020
43
0
I already use Sygic because I’m in middle east but I try to download navitel for testing is working no issues as you can see in pictures but trying to reinstall
hi
did you tried assign Navitel app to NAVI button and tried launch Navitel by NAVI button?
because this app can open by touch to app icon but not work with Navi button :D this has never happened before
 

TNSMANI

Senior Moderator
Staff member
Jan 8, 2014
5,309
1
6,899
Chennai
MOD ACTION:

Guys,

Please use English on XDA as per Rule 4:

4. Use the English language.

We understand that with all the different nationalities, not everyone speaks English well, but please try. If you're really unable to post in English, use an online translator. You're free to include your original message in your own language, below the English translation. (This rule covers your posts, profile entries and signature). You could try :- https://translate.google.com/ or https://www.babelfish.com/ or use one of your choice.
As a matter of courtesy, I have now translated multiple posts into English. In case any future posts are posted in non-English, please note that we will be constrained to delete them.
 

ngviethoa

Member
Oct 17, 2020
43
0
KLYDE sent me latest build Android 10 for MCU no DSP, everyone can try it
newest build is 202106011002
 
Last edited:

abdelmonem

Member
Jan 26, 2009
45
5
hi
did you tried assign Navitel app to NAVI button and tried launch Navitel by NAVI button?
because this app can open by touch to app icon but not work with Navi button :D this has never happened before
Yes I try it ,it’s working and all Function is available I try last 4 android 10 version all is good but Erisin launcher version is sometimes have some issues in reverse cam or screen stuck
 

abdelmonem

Member
Jan 26, 2009
45
5
after extract zip file in updater-script i find this


Code:
getprop("ro.product.device") == "rk3368_Android10" || abort("E3004: This package is for \"rk3368_Android10\" devices; this is a \"" + getprop("ro.product.device") + "\".");
ui_print("Target: rockchip/rk3368_Android10/rk3368_Android10:10/QQ2A.200305.004.A1/eng.ken.20201030.104745:userdebug/test-keys");
show_progress(0.650000, 0);
 

Top Liked Posts

  • There are no posts matching your filters.
  • 1
    Oh My Gosh, again a wrong resolution... Your unit is 800*480 while you updated with the file for 1024*600. Fix is there
    1
    so? is px5 or px6?


    the file is no longer available ....
    It’s for px5
  • 26
    This thread relates to MCU: CSN2_xxxxx, CSN2_D_xxxxx and CSN2_8600_D_xxxxx for PX4, PX5 and PX6 platforms


    This thread is a mirror of russian 4pda to cover more users/developers.

    All units are made by Klyde, but are sold under different brands.

    I've been looking for a simple way to donate me if this thread is useful for you, all the ways are collected in one post there

    The thread requires a new mainteiner. Details are there.

    Hardware specifications:

    • CPU: Octa-core PX5 1.5GHz Cortex A53 64 bits CPU
    • ROM: 16/32/64G
    • RAM: 2/4G
    • Resolution: 1024*600
    • Out Power: 4*45Watt
    • Operating System: Android 8/9
    • Radio Tuner/Audio Chip: NXP6686 / TDA7851
    • Built-In WiFi Module /Support External 3G Dongle
    • Features: Radio Tuner,Built-in GPS,MP3 Player,Bluetooth,Touch Screen,TV,Mirror link,Built-In Microphone,Support Steering Wheel Control,Support Can-Bus

    Useful tips
    Tag [Android 8] means that it applicable to Android 8 :), the same for [Android 9]. If there is no tag, it suits both versions.


    • Factory Settings password: 126
    • If you type 888 while opening Factory Settings, the Logo changing menu appears instead of Factory Settings. Logo1 replaces "Navigation system" picture, Logo2 replaces "android" picture. Logo2 is animated.
    • Developers mode password is 237
    • Password 927 opens menu, that helps to adjust screen brightens by changing VCOM value. You can set it between 1 and 100. Be careful with that!
    • [Android 8] How to get root: Use a rooting app, alternative link
    • [Android 9] How to root
      Warning! You should be careful with that as it can brick your device once you tried to update SuperSu. Do not update SuperSu binary or the SuperSU app!!! You will get bootloop if that is updated!!! Also you have to wait until the tool completes its job, otherwise you can get no sound. If you face the mentioned problems, just re-flash your device. BE CAREFUL!.
    • Starting from android 8 January firmware there is an option "OFF" for "Power off delay if ACC OFF". it allows to keep android in a sleep mode forever. Please note that it consumes around ~9-10mA in this mode. Powered off device uses 4.8mA only (twice less than sleeping mode).
    • How to get enter stock recovery: hold reset(power) button, wait until sensor buttons start blinking, release and immediately press the button again. See video
    • To adjust the back camera brightness, just tap the screen when the camera is active.
    • Set custom logo
    • Detailed device schema

    Known issues/limitations and fix/workaround for that
    • Lost wheel key settings and radio stations in case full power loss (yellow wire). Make sure that yellow wire is not disconnected when the car is stopped/locked.
    • Sound level is 10 (12) after reboot/sleep if you was listening louder; if it was less than 10 (12) stays the same. 12 appeared in Dec 11th firmware, it was 10 before that. Not topical starting from Dec 27th firmware, now you can define default sound between 12 10 and 20 in Car Settings-->Personal Settings. 10-20 is in Jan 17th firmware .
    • buzz in speakers caused by 433MHz alarm system and USB stick remounting.
    • small buzz caused by WIFI, observed in complete silence only. Not an issue if there are no connected devices.
    • There are lots of cases when wheel keys does not work at all. The reason is in wiring. Please study the head unit manual + car wiring scheme and put the needed wire to the correct connection shoe.
    • if you have canbus adapter and wheel buttons duplicate actions (i.e you pressed next track, but 2-3 tracks were switched, the same for sound level), just flash Jan 17 or newer firmware. Also it is possible to change wiring, but the firmware is much easier.
    • if you have canbus adapter and track switching is reversed (incorrect), just go to Factory Settings --> canbus and set keys_previous_next to change.
    • Bluetooth ODBII and hands-free (calls) does not work simultaneously. At the same time ODBII and BT Music works well simultaneously. Hardware limitation, no idea for now if that can be solved.
    • Voice dialing, voice search do not work on some devices. Fixed in May 8th firmware.

    1.PX5 Firmware.
    You can combine different firmware and MCU (I.e. take the pumpkin MCU + April firmware or vice versa). MCU from Android 8 is compatible with Android 9. Mind DSP only while updating MCU.

    The factory does not provide me with a changelog! Do not ask about it.

    Android 10.


    Fake Android 10.
    It is the same android 9 firmware, but with changed launcher, radio and Bluetooth app.
    Android 9.

    The link for the most recent firmware and MCU: with DSP and without DSP. _D_ in the MCU version means that it is for units with DSP.

    All available versions of MCU are on my Google drive.

    Firmware history and links:
    Android 8.
    The link for the most recent firmware and MCU: with DSP and without DSP. _D_ in the MCU version means that it is for units with DSP.

    All available versions of MCU are on my Google drive.

    Firmware history and links:

    2. PX6 Firmware

    Android 10.

    Android 9.

    3. PX5 Android 9 for 1 DIN units with MCU CSN2_8600_D
    The differences between this unit are on Russian 4pda

    Firmware 201911301053 + MCU CSN2_8600_D_11202019_162651 is located on Google Drive

    4. PX4 Firmware

    Android 10.

    The instruction how to upgrade is there

    The list of purchased devices

    Tested and compatible 3G/4G modems
    • ZTE MF622
    • ZTE MF825
    • Huawei e173
    • Huawei E352
    • Huawei E3272
    • Alcatel 410D
    9
    How to update firmware on the device (without changing android version)

    I know at least 3 methods how to do that :) Use USB Stick or SD card with FAT32 filesystem for android 8 or USB Stick ONLY for android 9.
    1.
    - put the firmware (kupdate.zip + update2.bin if you want to upgrade MCU) directly to USB stick or SD card,
    - insert it while the unit is running,
    - click OK once suggestion to update appears.

    2. The same as 1, but the last point is to start update from system settings

    3. Use it, if you have a brick (bootloop)
    - put the firmware (kupdate.zip + update2.bin if you want to upgrade MCU) directly to USB stick or SD card with FAT32 filesystem for android 8 or ONLY USB Stick for android 9.
    - power off the device, insert USB stick or SD card for android 8 or ONLY USB Stick for android 9.
    - press and hold power button and power on unit by switching on ACC in your car or enable power +12V on both red and yellow wire in case you doing that on the table. On some units use reset button instead.
    - once the update is started, release the button.

    WARNING! Firmware update will remove all your personal data and settings on the device!

    If you observe the error like "header and footer of kupdate.zip does not correspond signature", just try to upgrade form another USB stick/SD card.
    5
    Upgrade to real android 10

    There are 2 known ways how to upgrade to android 10.


    1. Disassemble your unit and do the same as described there using the files for PX5 or PX6 depending on your platform. Also there is an instruction with pictures in each archive.

    2. Without disassembling, but using windows laptop or tablet. Quite simple, but requires lots of checks and preparations. And in worth case scenario you will have to solder to the needed pins of coreboard.

    !!! The upgrade is possible on motherboards rev 1.4, 1.5.2 and 1.6 (quite possible that other revisions too, but we have not enough information for now). The mainboards of rev 1.2 require disassembling and soldering additional usb cable!!!

    In order to complete the upgrade we need:
    - strong desire to do that and be ready to disassemble unit in case of the failure or even purchase a new one.
    - USB type A male to type A male cable
    - Windows laptop or tablet

    Steps to do.
    1. Preparation
    - check the Bluetooth module that is configured in your unit: System Settings-->Factory Settings-->FUNC-->BT Mode. Note its model somewhere. That will be needed to restore the settings after the upgrade.
    - check if you can do an upgrade:
    -- install terminal emulator on your unit and run
    Code:
    dmesg | grep "USB device" | grep using
    and note the last time stamp
    -- plug USB stick to the first USB (on the panel or into an extender cable)
    -- run again
    Code:
    dmesg | grep "USB device" | grep using
    -- if you see something like
    Code:
    [ 4781.749803] usb 3-1: new high-speed USB device number 16 using usb20_otg
    you can use this USB and plug the head unit to your laptop via it using USB male type A to male type A cable. usb20_otg is vital
    -- if you see something like
    Code:
    1-1.3: new high-speed USB device number 5 using ehci-platform
    This USB can not be used!
    -- repeat the action for the second unit`s USB
    -- IF BOTH PORTS DOES NOT HAVE OTG YOU CAN NOT GO FURTHER UNTIL YOU SOLDER THE 3RD CABLE! The instruction is at the end of this post.
    - download PX5 or PX6 depending on your platform.
    - if you have a display with resolution 1280*720 , download a custom oem.img, it is suitable for both PX5 and PX6;
    - extract archive to root directore of drive C: You should have C:\px6_10.0_burntools\ or C:\px5_10.0_burntools\ folder;
    - install drivers from DriverAssitant folder;
    - in case of PX6 go to C:\px6_10.0_burntools\AndroidTool_Release_v2.71, for PX5 go to C:\px5_10.0_burntools\AndroidTool_Release_v2.71, edit config.ini, replace Selected=1 with Selected=2. That will enable English language for the program;
    - if you have 1280*720 display, put the custom file to rockdev\image folder and replace the old one;
    - backup all vital data on your head unit;

    2. Upgrade
    - run AndroidTool.exe
    - download and install this APK
    - run it and click "Go to Android10", the device will be rebooted and BRICKED. APK kills loader and boot partition!!!
    - connect your laptop and head unit via the discovered OTG USB
    - AndroidTool should reprt "Found one MASKROM device"
    - hit run button;
    - wait until the competition.

    The unit will be rebooted, data partition will be formated and the unit will be running andriod 10.

    3. Post upgrade
    - download the most recent firmware
    - put it on USB stick
    - do an upgrade using this USB stick

    Known issues and fixes
    1. Bluetooth KD6 does not work on android 10. Replace the module with IVT140 or RF210, maybe it will be fixed in new firmware. Fixed starting from 202011261850
    2. In some unique cases the rear camera does not work on android 10 (we suspect that it appears on old mainboard revisions without DSP). Fix is to revert to android 9 or maybe it will be fixed in new firmware. Fixed starting from 202010141730



    TIPs
    .
    Mainboards Rev 1.2 do not have USB OTG, so you have to solder the 3d USB cable. Just solder the USB wire to connector A if the mainboard. Pins 63 and 64. 63rd stands for D+, 64th corresponds D-. Do not forget about GND. +5V is not mandatory for upgrade, you can take it from rear connector H (check pin 5 or 10 there) and make fully working USB port.

    20818804.png

    photo_2020-09-13_14-36-50.jpg

    photo_2020-09-13_14-30-35.jpg
    4
    Upgrade from Android 8 to 9 WITHOUT disassembling.

    ALL YOUR ACTIONS ARE YOUR OWN RESPONSIBILITY!!! Nobody will send you a new core board in case of the failure! At least will not do that free of charge!

    0. All needed files are there.

    1. To perform the upgrade we need:
    - Strong desire to do that and be ready to purchase a new core board in case of total failure (~100$);
    - micro SD card slot in your unit. If the unit vendor gives details regarding the units without SD cards, I'll update this post;
    - USB stick (up to 16GB, to avoid possible problems) formatted in fat32;
    - micro SD card (again, please use not so big);

    2. Put the following things on USB stick:
    - MCU firmware that suits your device. I.e. update2.bin from the first message in thread with DSP or not depending on your unit)
    - Android 9 firmware from the first message. kupdate.zip, Again: Andriod 9!!!

    3. Do NOT plug USB stick to the unit for now, let`s make bootable SD card;

    4. On Windows PC run SDDiskTool and create bootable SD card. The manual inside of the archive, with the details, so I see to reasons to repeat it there. update.img from the archive is used there ~350Mb;

    5. Install "Android 8 upgrade 9.apk" into the unit, run it, click only the button in this application. The unit becomes a brick (temporary, till a success on step 9) - You will see only a black screen and lights on the buttons;

    6. Put SD card into a units slot, disconnect battery terminal of your car or power off the unit in some other way. Both red and yellow wires of unit should not have +12V on them !!!

    7. connect battery terminal.

    8. The unit is upgraded for the first time. Take a video of the process!!! Just in case if you fail and it will be needed to troubleshoot that. On this step you should see TWO errors of formatting metadata. YES, there should be TWO errors!! and formatting error for system.

    Video of attempt.
    The final screenshot.


    9. Disconnect and connect battery terminal one more time. The unit upgrades from SD card one more time Take a video of the process,just in case. this time there should be no errors with metadata and system!!! The last string should be "Doing Actions succeeded".

    Video of 2nd attempt.
    The final screenshot.


    10. Disconnect battery terminal, REMOVE SD card from unit, plug USB stick prepared on step 2.

    11. Connect battery terminal and the unit will complete the upgrade to Android 9.

    12. Once the upgrade from USB stick is done, the unit start running Android 9. All further upgrades will be done from USB stick without any additional actions

    Video of installing the firmware from USB Stick.

    13. FORMAT SD card on your PC, do not use it in unit until it is formatted, just to be safe.
    4

    I decompiled with the latest Jadx and found it will end all non-system processes, except for those in a hard-coded blacklist, which includes google maps. So it should work to move an app to system/priv-app or even system/app if it is desired to be sustained during sleep. There are apps which can do this for you on a rooted system though I have never tried them. Apparently it gets more complicated if the app to be made a system app includes libraries and I don't know if the automated systemizer apps do this for you. In my case it would be nice if Maps restarted where it left off so I may go ahead and try editing the smali.

    FYI the relevant code is below:
    It comes from com.my.manager.McuManager in MyCarService.apk. According the the manifest it was compiled with Android 9.

    Update: I was not able to successfully rebuild a properly working apk. :(

    2nd Update: With apktool set to not use aapt2, it seems to work. I commented out the call to the below function, and now Google Maps resumes directly to navigation. Somehow it didn't do the trick to remove Maps from the blacklist. :)

    Code:
     private void killAllNoSystemProcess() {
            try {
                getAvailMemory(this.mContext);
                PackageManager mPackageManager = this.mContext.getPackageManager();
                Intent mainIntent = new Intent("android.intent.action.MAIN", null);
                mainIntent.addCategory("android.intent.category.LAUNCHER");
                List<ResolveInfo> apps = mPackageManager.queryIntentActivities(mainIntent, 0);
                ActivityManager am = (ActivityManager) this.mContext.getSystemService("activity");
                for (ActivityManager.RunningAppProcessInfo amProcess : am.getRunningAppProcesses()) {
                    int kill = -1;
                    Iterator<ResolveInfo> it = apps.iterator();
                    while (true) {
                        if (!it.hasNext()) {
                            break;
                        }
                        ResolveInfo appInfo = it.next();
                        boolean flag = false;
                        if ((appInfo.activityInfo.applicationInfo.flags & GlobalDef.CVBS_DEFALUT_BRIGHTNESS_7181) != 0) {
                            flag = true;
                        } else if ((appInfo.activityInfo.applicationInfo.flags & 1) == 0) {
                            flag = true;
                        }
                        if (amProcess.processName.startsWith(appInfo.activityInfo.packageName)) {
                            if (flag) {
                                kill = 1;
                            } else {
                                kill = 0;
                            }
                        }
                    }
                    if (kill == -1 && amProcess.importance > 200) {
                        kill = 1;
                    }
                    Log.d(TAG, amProcess.processName + "<<kill:" + kill + ":" + amProcess.importance);
                    if (kill > 0) {
                        am.forceStopPackage(amProcess.processName);
                    }
                    for (String s : KILL_SYSTEM_APP) {
                        am.forceStopPackage(s);
                    }
                }
                getAvailMemory(this.mContext);
            } catch (Exception e) {
                Log.d(TAG, "killAllNoSystemProcess:" + e);
            }
        }