General Medeke/Navifly 7862

[Radzią]

Yes, it has to be connected to cvbs in 1 and with "camera 12v" wire that is on the connector where the back camera connection is. I think you can display it with aux app. There is an option in the settings to display front camera after the back cam is closed, I do not have access to the unit now but it may be in factory settings ( I suggest check all the menus not only factory).

Thanks, All clear

 

[Hiro0111]

I recently purchased the m700. I'm using app torquepro with obd2 to solve a bluetooth problem. The mobile phone was fine, but the m700 doesn't seem to be able to read the accelerometer. please tell me in detail

 

[Radzią]

.

 

[Tomaso84]

Hello Does anyone know how to start OTG mode on 7862. I started debugging mode but my device is still silent.



Witam Czy ktoś wie, jak uruchomić tryb OTG w 7862. Uruchomiłem tryb debugowania, ale moje urządzenie nadal milczy.

 

[Kwen]

Does anyone know how I can change the refresh rate of the aux and reversing cameras?
My camera is currently black and white because it's trying to display it as the wrong format.

You need to enable AHD in the factory settings

 

[mokz2020]

hello guys im new here and recently purchased m600s. i already installed rear camera, and i want to install a front camera which will be located in the bumper. where can i connect it which rca. and what app will i use for the front camera to turn on.

 

[Wagemuth]

Hi guys I bought a m600. Everything fine, but one issue is not possible to fix…the Panel leds on the left side are not illuminated…since 1 week I have a conversation with the seller support… the wiring seems to be correct and all needed device setting at done … any idea or recommendations what needs to be checked from my side … if I don’t have a solution … I will send the unit back I assume the leds are broken…

 

[mokz2020]

in which rca should i connect the reverse cam and the front cam? thank you.

 

[marchnz]

View attachment 5603257
in which rca should i connect the reverse cam and the front cam? thank you.

Cross poster, what did the seller suggest or reputable installer recommend

 

[fr2lancer]

Hi.

I am thinking of buying this https://www.alibaba.com/product-det...spm=a2700.galleryofferlist.0.0.2bc7349fuhNtqF

- 2k-m700s(not in this link)

navifly 7862 8+128G and qled 2k version(I think it would address - higher resolution..)


My question is
1. navifly 7862 have compatibility with other companies' ahd rear camera?
2. And how about cc3? is that compatible with other companies ahd rear camera?
3. Lately, any advantage buying cc3 instead of navifly in techincal-wise?

Thank you.

 

[mokz2020]

Cross poster, what did the seller suggest or reputable installer recommend

they suggest connect the reverse cam in cam vin while the front cam, connect to cvbs in1

 

[BogdanSi]

Hello. I need your help. I bought MEKEDE M600s. SWC doesn't work for me. Please check my settings. What is wrong? Thank you.

 

[marchnz]

Hello. I need your help. I bought MEKEDE M600s. SWC doesn't work for me. Please check my settings. What is wrong? Thank you.

What does reseller suggest when contacted for support. Also any applicable posts in forums, what has been tried.

These forums require some effort and are not service forums, or guessing games.

 

[stealthee]

I have the Mekede 600 and when I push the Volume control that would turn off the original radio. It just turns off the screen. Is there A way to make it turn the radio on and off with the volume power button?

 

[Mojojosie]

Hi guys I bought a m600. Everything fine, but one issue is not possible to fix…the Panel leds on the left side are not illuminated…since 1 week I have a conversation with the seller support… the wiring seems to be correct and all needed device setting at done … any idea or recommendations what needs to be checked from my side … if I don’t have a solution … I will send the unit back I assume the leds are broken…

I had the same issue (only just worked it out today) its under "Backlight control" in "General" settings

 

[Wagemuth]

I had the same issue (only just worked it out today) its under "Backlight control" in "General" settings

All recommended setting were done also backlight control … the led panel board seems to be broken … seller send me a replacement, its already replaced but not tested yet…

 

[spludgey]

You need to enable AHD in the factory settings

Awesome, thanks very much, that did the trick.

 

[Wagemuth]

All recommended setting were done also backlight control … the led panel board seems to be broken … seller send me a replacement, its already replaced but not tested yet…

update from my side, after replacement of the panel light board I have the same issue, panel light is still not working, all recommended settings done, the ILL wire is energized, it just doesn't work...don't know if there's a connection... the RST button also shows no reaction and when I get calls the caller can't hear me, as if the internal microphone doesn't work, all components are attached to the light board...

 

[marchnz]

View attachment 5627711Is it possible to change the canbus settings app to that of another device?

The canbus settings on this unit are not detailed enough, and do not let you set anything other than “car model”.

Other units like PX5 have a more detailed app which lets you select “with amplifier”, which is required for my Peugeot car with JBL sound system to work properly.

I’m 99% certain the canbus itself (XP/simplesoft) is the same on both, it’s just that Mekede has an overly simplified settings page which hides critical settings that I need to tweak to get audio output working.

I’ve attached a picture which shows the advanced canbus settings offered by the PX5. Hoping somebody can help.

Which device? Px5 is a processor- there are multiple px5 fitted variants

 

[hothotramen]

Which device? Px5 is a processor- there are multiple px5 fitted variants

To give a bit more background, some Peugeot cars use JBL speaker setups which tend to not work with aftermarket head units.

However, I managed to find one forum post where somebody had that issue, but was able to fix it using those extra canbus config settings (specifically “with amplifier”). People usually blame the custom JBL amplifier for the compatibility issues so I’m nearly certain this is the actual solution.

In this forum post, they were using the device pictured above. They referred to it as an MX/Witson.

As you can see, it’s also a SimpleSoft canbus. This leads me to believe I just need to set that flag or something, but the Mekede devices have an overly simplified UI which doesn’t expose those config options.