Micromax NItro A311 stuck at 98% in YGDP

[firelordfld]

My canvas nitro a311 got stuck into a bootloop while i was flashing something using twrp. Unfortunately my twrp recovery mode also dissappeared (not opening). I tried to flash stock rom using ygdp but stucks at 98% with the error

CELL0: Check between YL-Parames Partition and PhoneInfo Failed.Error Code:11
CELL0: Check YL-Parames Partition Failed, The CPB is not for the Phone.

The phone keeps disconnecting after 10seconds or so. All the drivers are properly installed. Still of no use.


The full log of the dump is

CELL0: Software Version: Assembly - <V3.98_141222_02>
CELL0: Cell 0 USB address is: com7
CELL0: Start Download.
CELL0: Download Started...
CELL0: Downloading CPB:
CELL0: Init Connect Arg.
CELL0: Downlaod DA Start.
CELL0: Downlaod DA Success.
CELL0: Verify is Partition be Changed.
CELL0: Get Usb Status Success.
CELL0: Read YL-Parames Partition Start.
CELL0: Read YL-Parames Partition Success.
CELL0: Check between YL-Parames Partition and PhoneInfo Start.
CELL0: Check between YL-Parames Partition and PhoneInfo Failed.Error Code:11
21:16:15 CELL0: Check YL-Parames Partition Failed, The CPB is not for the Phone.
21:16:15 CELL0: DisConnect.
CELL0: Total download time elapsed: 0 min : 25 sec CELL0: Downloading CPB: Failed!

Earlier i have used the same CPB file many times to flash.
At 98% phone disconnects. It happens everytime
Please reply ASAP. Its very Important. Ask if any details needed

 

[shivam883]

My canvas nitro a311 got stuck into a bootloop while i was flashing something using twrp. Unfortunately my twrp recovery mode also dissappeared (not opening). I tried to flash stock rom using ygdp but stucks at 98% with the error

CELL0: Check between YL-Parames Partition and PhoneInfo Failed.Error Code:11
CELL0: Check YL-Parames Partition Failed, The CPB is not for the Phone.

The phone keeps disconnecting after 10seconds or so. All the drivers are properly installed. Still of no use.


The full log of the dump is

CELL0: Software Version: Assembly - <V3.98_141222_02>
CELL0: Cell 0 USB address is: com7
CELL0: Start Download.
CELL0: Download Started...
CELL0: Downloading CPB:
CELL0: Init Connect Arg.
CELL0: Downlaod DA Start.
CELL0: Downlaod DA Success.
CELL0: Verify is Partition be Changed.
CELL0: Get Usb Status Success.
CELL0: Read YL-Parames Partition Start.
CELL0: Read YL-Parames Partition Success.
CELL0: Check between YL-Parames Partition and PhoneInfo Start.
CELL0: Check between YL-Parames Partition and PhoneInfo Failed.Error Code:11
21:16:15 CELL0: Check YL-Parames Partition Failed, The CPB is not for the Phone.
21:16:15 CELL0: DisConnect.
CELL0: Total download time elapsed: 0 min : 25 sec CELL0: Downloading CPB: Failed!

Earlier i have used the same CPB file many times to flash.
At 98% phone disconnects. It happens everytime
Please reply ASAP. Its very Important. Ask if any details needed

Same problem here also please help him and me both ASAP.

Sent from my YU5010 using Tapatalk

 

[sidhant1]

please help us same issue i have a311 tried all cpb roms, Customer care also cant fix

:crying::crying:crying:

Same problem here also please help him and me both ASAP.

Sent from my YU5010 using Tapatalk

 

[surendradhruwanshi]

a311 stop at 83% ........same problem................please help

 

[sidhant1]

Found solution... Reboot into fastboot mode, hold both volume buttons and power on... Flash preloader.bin using fastboot... Then flash rom using sp flash tool.. My insta @SSidhantgupta