Moto G Boot up failed

[angelgzg]

Good my phone has suddenly been hung and when forced reboot is then left in the logo of motorola and it's not from there, I tried to make this tutorial and "appears" that does everything well but then when rebooting just does not start as usual

When trying to enter the recovery says "boot up failed" and tried to install a custom recovery and I get the same

 

[oversleeper]

Good my phone has suddenly been hung and when forced reboot is then left in the logo of motorola and it's not from there, I tried to make this tutorial and "appears" that does everything well but then when rebooting just does not start as usual

When trying to enter the recovery says "boot up failed" and tried to install a custom recovery and I get the same

Try to reflash the stock firmware or, even better, the 4.4.4 of your stock firmware.

 

[angelgzg]

Try to reflash the stock firmware or, even better, the 4.4.4 of your stock firmware.

Where I can download a 4.4.4 firmware and not a full upgrade? and 4.4.3 and try anything

 

[oversleeper]

Where I can download a 4.4.4 firmware and not a full upgrade? and 4.4.3 and try anything

Here

 

[angelgzg]

Here

I get these errors trying

hab check failed for boot
hab check failed for recovery

 

[oversleeper]

I get these errors trying

hab check failed for boot
hab check failed for recovery

That's because you're flashing a non stock firmware. Just ignore that error. Run all commands and all should work properly.

 

[angelgzg]

That's because you're flashing a non stock firmware. Just ignore that error. Run all commands and all should work properly.

This error also should ignore it?

piv signed invalid system image

Just do not start everything but it stays on the logo and I can not get into the recovery?

I'm thinking that the problem is hardware: ((((

 

[oversleeper]

This error also should ignore it?

piv signed invalid system image

Just do not start everything but it stays on the logo and I can not get into the recovery?

I'm thinking that the problem is hardware: ((((

Run the command fastboot.exe getvar all or mfastboot.exe getvar all and post the result.

 

[angelgzg]

Run the command fastboot.exe getvar all or mfastboot.exe getvar all and post the result.

C:\Users\Usuario\Desktop\Minimal ADB and Fastboot>mfastboot.exe getvar all
version: 0.5
version-bootloader: 4111
product: falcon
secure: yes
hwrev: 0x83C0
radio: 0x1
emmc: 16GB Sandisk REV=06 PRV=07 TYPE=17
ram: 1024MB Samsung S4 SDRAM DIE=4Gb
cpu: MSM8226 CS
serialno: TA93005UU8
cid: 0x0009
channelid: 0x00
uid: C3A9C5020F000000000000000000
unlocked: no
iswarrantyvoid: no
mot_sst: 0
max-download-size: 536870912
reason: Volume down key pressed
imei:
meid:
date:
sku:
iccid:
cust_md5:
max-sparse-size: 268435456
current-time: "Wed Aug 6 0:23: 7 UTC 2014"
ro.build.fingerprint[0]: motorola/falcon_retuglb/falcon_umt
ro.build.fingerprint[1]: s:4.4.3/KXB21.14-L1.32/33:user/rel
ro.build.fingerprint[2]: ease-keys
ro.build.version.full[0]: Blur_Version.210.12.32.falcon_umt
ro.build.version.full[1]: s.Retail.en.US
ro.build.version.qcom[0]: AU_LINUX_ANDROID_LNX.LA.3.5.1_RB1
ro.build.version.qcom[1]: .04.04.02.048.020
version-baseband:
kernel.version[0]: Linux version 3.4.42-g26ca2df ([email protected]
kernel.version[1]: ilclbld54) (gcc version 4.7 (GCC) ) #1 S
kernel.version[2]: MP PREEMPT Fri May 30 11:08:03 CDT 2014
sdi.git: git=MBM-NG-V41.11-0-gdc5aeaf
sbl1.git: git=MBM-NG-V41.11-0-gcff5797
rpm.git: git=MBM-NG-V41.11-0-g71b1aae
tz.git: git=MBM-NG-V41.11-0-ga27c415
aboot.git: git=MBM-NG-V41.11-0-g7d46a5a
qe: qe 0/1
ro.carrier: unknown
all: listed above
finished. total time: 0.155s

 

[oversleeper]

C:\Users\Usuario\Desktop\Minimal ADB and Fastboot>mfastboot.exe getvar all
version: 0.5
version-bootloader: 4111
product: falcon
secure: yes
hwrev: 0x83C0
radio: 0x1
emmc: 16GB Sandisk REV=06 PRV=07 TYPE=17
ram: 1024MB Samsung S4 SDRAM DIE=4Gb
cpu: MSM8226 CS
serialno: TA93005UU8
cid: 0x0009
channelid: 0x00
uid: C3A9C5020F000000000000000000
unlocked: no
iswarrantyvoid: no
mot_sst: 0
max-download-size: 536870912
reason: Volume down key pressed
imei:
meid:
date:
sku:
iccid:
cust_md5:
max-sparse-size: 268435456
current-time: "Wed Aug 6 0:23: 7 UTC 2014"
ro.build.fingerprint[0]: motorola/falcon_retuglb/falcon_umt
ro.build.fingerprint[1]: s:4.4.3/KXB21.14-L1.32/33:user/rel
ro.build.fingerprint[2]: ease-keys
ro.build.version.full[0]: Blur_Version.210.12.32.falcon_umt
ro.build.version.full[1]: s.Retail.en.US
ro.build.version.qcom[0]: AU_LINUX_ANDROID_LNX.LA.3.5.1_RB1
ro.build.version.qcom[1]: .04.04.02.048.020
version-baseband:
kernel.version[0]: Linux version 3.4.42-g26ca2df ([email protected]
kernel.version[1]: ilclbld54) (gcc version 4.7 (GCC) ) #1 S
kernel.version[2]: MP PREEMPT Fri May 30 11:08:03 CDT 2014
sdi.git: git=MBM-NG-V41.11-0-gdc5aeaf
sbl1.git: git=MBM-NG-V41.11-0-gcff5797
rpm.git: git=MBM-NG-V41.11-0-g71b1aae
tz.git: git=MBM-NG-V41.11-0-ga27c415
aboot.git: git=MBM-NG-V41.11-0-g7d46a5a
qe: qe 0/1
ro.carrier: unknown
all: listed above
finished. total time: 0.155s

Download this.

 

[angelgzg]

Download this.

Now try this firmware installation and does everything well without errors but when restart is the motorola logo

any way to know if this completely-dead?

 

[oversleeper]

Now try this firmware installation and does everything well without errors but when restart is the motorola logo

any way to know if this completely-dead?

Since you are under warranty the best thing to do is to send it to Motorola...

 

[angelgzg]

Since you are under warranty the best thing to do is to send it to Motorola...

Well I bought it from amazon USA, I'm from Venezuela so I think that's not a possibility? that alternatives do I have? it could be converted into brick? unbrick then?

I also tried unlocking the bootloader and I get the message in purple unlocked and restarted but then goes into fastboot mode as if not done


I changed usb cable and now I get status code = 3, but now does not advance after the warning screen and enter android recovery goes the "no command"

 

[oversleeper]

Well I bought it from amazon USA, I'm from Venezuela so I think that's not a possibility? that alternatives do I have? it could be converted into brick? unbrick then?

I also tried unlocking the bootloader and I get the message in purple unlocked and restarted but then goes into fastboot mode as if not done


I changed usb cable and now I get status code = 3, but now does not advance after the warning screen and enter android recovery goes the "no command"

Ok... now your bootloader is unlocked and your warranty gone, so you can try the next level. Follow my thread. You have to use the bricker script, then when your device will be recognized as qhsusb_bulk I'll give you the tool to reflash the bootloader.

 

[angelgzg]

Ok... now your bootloader is unlocked and your warranty gone, so you can try the next level. Follow my thread. You have to use the bricker script, then when your device will be recognized as qhsusb_bulk I'll give you the tool to reflash the bootloader.

Well now the computer does not pass the warning screen when entering the bootloader and recovery I get the android with exclamation mark and says no command

this is the phone info using this command (mfastboot.exe getvar all)

C:\Minimal ADB and Fastboot>mfastboot.exe getvar all
(bootloader) version: 0.5
(bootloader) version-bootloader: 4111
(bootloader) product: falcon
(bootloader) secure: yes
(bootloader) hwrev: 0x83C0
(bootloader) radio: 0x1
(bootloader) emmc: 16GB Sandisk REV=06 PRV=07 TYPE=17
(bootloader) ram: 1024MB Samsung S4 SDRAM DIE=4Gb
(bootloader) cpu: MSM8226 CS
(bootloader) serialno: TA93005UU8
(bootloader) cid: 0x0009
(bootloader) channelid: 0x00
(bootloader) uid: C3A9C5020F000000000000000000
(bootloader) unlocked: yes
(bootloader) iswarrantyvoid: yes
(bootloader) mot_sst: 3
(bootloader) max-download-size: 536870912
(bootloader) reason: Volume down key pressed
(bootloader) imei:
(bootloader) meid:
(bootloader) date:
(bootloader) sku:
(bootloader) iccid:
(bootloader) cust_md5:
(bootloader) max-sparse-size: 268435456
(bootloader) current-time: "Wed Aug 6 3:39:14 UTC 2014"
(bootloader) ro.build.fingerprint[0]: motorola/falcon_retuglb/falcon_umt
(bootloader) ro.build.fingerprint[1]: s:4.4.3/KXB21.14-L1.32/33:user/rel
(bootloader) ro.build.fingerprint[2]: ease-keys
(bootloader) ro.build.version.full[0]: Blur_Version.210.12.32.falcon_umt
(bootloader) ro.build.version.full[1]: s.Retail.en.US
(bootloader) ro.build.version.qcom[0]: AU_LINUX_ANDROID_LNX.LA.3.5.1_RB1
(bootloader) ro.build.version.qcom[1]: .04.04.02.048.020
(bootloader) version-baseband:
(bootloader) kernel.version[0]: Linux version 3.4.42-g26ca2df ([email protected]
(bootloader) kernel.version[1]: ilclbld54) (gcc version 4.7 (GCC) ) #1 S
(bootloader) kernel.version[2]: MP PREEMPT Fri May 30 11:08:03 CDT 2014
(bootloader) sdi.git: git=MBM-NG-V41.11-0-gdc5aeaf
(bootloader) sbl1.git: git=MBM-NG-V41.11-0-gcff5797
(bootloader) rpm.git: git=MBM-NG-V41.11-0-g71b1aae
(bootloader) tz.git: git=MBM-NG-V41.11-0-ga27c415
(bootloader) aboot.git: git=MBM-NG-V41.11-0-g7d46a5a
(bootloader) qe: qe 0/1
(bootloader) ro.carrier: unknown
all: listed above
finished. total time: 0.054s

C:\Minimal ADB and Fastboot>

 

[angelgzg]

Ok... now your bootloader is unlocked and your warranty gone, so you can try the next level. Follow my thread. You have to use the bricker script, then when your device will be recognized as qhsusb_bulk I'll give you the tool to reflash the bootloader.

after using the recommended script happens happens happens

WARNING: READ CAREFULLY BEFORE YOU PROCEED!

THIS SCRIPT WILL DESTROY THE BOOTLOADER OF YOUR DEVICE.
DO NOT ATTEMPT TO USE UNLESS YOU'RE SURE ABOUT WHAT YOU'RE DOING.
ONLY YOU ARE RESPONSIBLE FOR YOUR ACTIONS.

Do you want to continue [Y / N]?, And

target-sparse max-size: 256MB
sending 'fsg' (102 KB) ...
OKAY [0.027s]
writing 'fsg' ...
OKAY [3.145s]
finished. Total time: 3.175s
target-sparse max-size: 256MB
sending 'rpm' (200 KB) ...
OKAY [0.038s]
writing 'rpm' ...
(bootloader) Preflash validation failed
FAILED (remote failure)
finished. Total time: 0.330s
target-sparse max-size: 256MB
sending 'SBL1' (264 KB) ...
OKAY [0.057s]
writing 'SBL1' ...
OKAY [0.028s]
finished. Total time: 0.088s
target-sparse max-size: 256MB
sending 'sdi' (32 KB) ...
OKAY [0.058s]
writing 'sdi' ...
(bootloader) Preflash validation failed
FAILED (remote failure)
finished. Total time: 0.343s
target-sparse max-size: 256MB
sending 'tz' (400 KB) ...
OKAY [0.084s]
writing 'tz' ...
(bootloader) Preflash validation failed
FAILED (remote failure)
finished. Total time: 0.392s
rebooting ...

finished. Total time: 0.003s

Your device is now hard bricked!

Press any key to continue. . .



But still I can get into fastboot mode and the pc recognizes me as android device

 

[oversleeper]

after using the recommended script happens happens happens

WARNING: READ CAREFULLY BEFORE YOU PROCEED!

THIS SCRIPT WILL DESTROY THE BOOTLOADER OF YOUR DEVICE.
DO NOT ATTEMPT TO USE UNLESS YOU'RE SURE ABOUT WHAT YOU'RE DOING.
ONLY YOU ARE RESPONSIBLE FOR YOUR ACTIONS.

Do you want to continue [Y / N]?, And

target-sparse max-size: 256MB
sending 'fsg' (102 KB) ...
OKAY [0.027s]
writing 'fsg' ...
OKAY [3.145s]
finished. Total time: 3.175s
target-sparse max-size: 256MB
sending 'rpm' (200 KB) ...
OKAY [0.038s]
writing 'rpm' ...
(bootloader) Preflash validation failed
FAILED (remote failure)
finished. Total time: 0.330s
target-sparse max-size: 256MB
sending 'SBL1' (264 KB) ...
OKAY [0.057s]
writing 'SBL1' ...
OKAY [0.028s]
finished. Total time: 0.088s
target-sparse max-size: 256MB
sending 'sdi' (32 KB) ...
OKAY [0.058s]
writing 'sdi' ...
(bootloader) Preflash validation failed
FAILED (remote failure)
finished. Total time: 0.343s
target-sparse max-size: 256MB
sending 'tz' (400 KB) ...
OKAY [0.084s]
writing 'tz' ...
(bootloader) Preflash validation failed
FAILED (remote failure)
finished. Total time: 0.392s
rebooting ...

finished. Total time: 0.003s

Your device is now hard bricked!

Press any key to continue. . .



But still I can get into fastboot mode and the pc recognizes me as android device

Try to download this and run the boot loader tool first. Post the result.

 

[angelgzg]

Try to download this and run the boot loader tool first. Post the result.

It seems like everything I do not change anything

Install recovery shows no error, but still comes out the same and yet so

C:\Users\PC\Desktop\Tools\DeviceInfo>mfastboot getvar all
(bootloader) version: 0.5
(bootloader) version-bootloader: 4111
(bootloader) product: falcon
(bootloader) secure: yes
(bootloader) hwrev: 0x83C0
(bootloader) radio: 0x1
(bootloader) emmc: 16GB Sandisk REV=06 PRV=07 TYPE=17
(bootloader) ram: 1024MB Samsung S4 SDRAM DIE=4Gb
(bootloader) cpu: MSM8226 CS
(bootloader) serialno: TA93005UU8
(bootloader) cid: 0x0009
(bootloader) channelid: 0x00
(bootloader) uid: C3A9C5020F000000000000000000
(bootloader) unlocked: yes
(bootloader) iswarrantyvoid: yes
(bootloader) mot_sst: 3
(bootloader) max-download-size: 536870912
(bootloader) reason: Volume down key pressed
(bootloader) imei:
(bootloader) meid:
(bootloader) date:
(bootloader) sku:
(bootloader) iccid:
(bootloader) cust_md5:
(bootloader) max-sparse-size: 268435456
(bootloader) current-time: "Wed Aug 6 14: 2:16 UTC 2014"
(bootloader) ro.build.fingerprint[0]: motorola/falcon_retuglb/falcon_umt
(bootloader) ro.build.fingerprint[1]: s:4.4.3/KXB21.14-L1.32/33:user/rel
(bootloader) ro.build.fingerprint[2]: ease-keys
(bootloader) ro.build.version.full[0]: Blur_Version.210.12.32.falcon_umt
(bootloader) ro.build.version.full[1]: s.Retail.en.US
(bootloader) ro.build.version.qcom[0]: AU_LINUX_ANDROID_LNX.LA.3.5.1_RB1
(bootloader) ro.build.version.qcom[1]: .04.04.02.048.020
(bootloader) version-baseband:
(bootloader) kernel.version[0]: Linux version 3.4.42-g26ca2df ([email protected]
(bootloader) kernel.version[1]: ilclbld54) (gcc version 4.7 (GCC) ) #1 S
(bootloader) kernel.version[2]: MP PREEMPT Fri May 30 11:08:03 CDT 2014
(bootloader) sdi.git: git=MBM-NG-V41.11-0-gdc5aeaf
(bootloader) sbl1.git: git=MBM-NG-V41.11-0-gcff5797
(bootloader) rpm.git: git=MBM-NG-V41.11-0-g71b1aae
(bootloader) tz.git: git=MBM-NG-V41.11-0-ga27c415
(bootloader) aboot.git: git=MBM-NG-V41.11-0-g7d46a5a
(bootloader) qe: qe 0/1
(bootloader) ro.carrier: unknown
all: listed above
finished. total time: 0.055s

C:\Users\PC\Desktop\Tools\DeviceInfo>pause
Presione una tecla para continuar . . .

 

[oversleeper]

It seems like everything I do not change anything

Install recovery shows no error, but still comes out the same and yet so

C:\Users\PC\Desktop\Tools\DeviceInfo>mfastboot getvar all
(bootloader) version: 0.5
(bootloader) version-bootloader: 4111
(bootloader) product: falcon
(bootloader) secure: yes
(bootloader) hwrev: 0x83C0
(bootloader) radio: 0x1
(bootloader) emmc: 16GB Sandisk REV=06 PRV=07 TYPE=17
(bootloader) ram: 1024MB Samsung S4 SDRAM DIE=4Gb
(bootloader) cpu: MSM8226 CS
(bootloader) serialno: TA93005UU8
(bootloader) cid: 0x0009
(bootloader) channelid: 0x00
(bootloader) uid: C3A9C5020F000000000000000000
(bootloader) unlocked: yes
(bootloader) iswarrantyvoid: yes
(bootloader) mot_sst: 3
(bootloader) max-download-size: 536870912
(bootloader) reason: Volume down key pressed
(bootloader) imei:
(bootloader) meid:
(bootloader) date:
(bootloader) sku:
(bootloader) iccid:
(bootloader) cust_md5:
(bootloader) max-sparse-size: 268435456
(bootloader) current-time: "Wed Aug 6 14: 2:16 UTC 2014"
(bootloader) ro.build.fingerprint[0]: motorola/falcon_retuglb/falcon_umt
(bootloader) ro.build.fingerprint[1]: s:4.4.3/KXB21.14-L1.32/33:user/rel
(bootloader) ro.build.fingerprint[2]: ease-keys
(bootloader) ro.build.version.full[0]: Blur_Version.210.12.32.falcon_umt
(bootloader) ro.build.version.full[1]: s.Retail.en.US
(bootloader) ro.build.version.qcom[0]: AU_LINUX_ANDROID_LNX.LA.3.5.1_RB1
(bootloader) ro.build.version.qcom[1]: .04.04.02.048.020
(bootloader) version-baseband:
(bootloader) kernel.version[0]: Linux version 3.4.42-g26ca2df ([email protected]
(bootloader) kernel.version[1]: ilclbld54) (gcc version 4.7 (GCC) ) #1 S
(bootloader) kernel.version[2]: MP PREEMPT Fri May 30 11:08:03 CDT 2014
(bootloader) sdi.git: git=MBM-NG-V41.11-0-gdc5aeaf
(bootloader) sbl1.git: git=MBM-NG-V41.11-0-gcff5797
(bootloader) rpm.git: git=MBM-NG-V41.11-0-g71b1aae
(bootloader) tz.git: git=MBM-NG-V41.11-0-ga27c415
(bootloader) aboot.git: git=MBM-NG-V41.11-0-g7d46a5a
(bootloader) qe: qe 0/1
(bootloader) ro.carrier: unknown
all: listed above
finished. total time: 0.055s

C:\Users\PC\Desktop\Tools\DeviceInfo>pause
Presione una tecla para continuar . . .

Try the others 2 tools in the package. Don't worry I think your device is ok.

 

[angelgzg]

Try the others 2 tools in the package. Don't worry I think your device is ok.

What other options do I have?