New Nook Glowlight Plus

[Renate]

How would I know? What's the status of things now?

 

[gmwgj]

A removable disk appeared, I didn't format it.

 

[Renate]

Doesn't the screen show anything? Do you have ADB?

 

[Renate]

You're going to have to speak in full sentences and tell me what's going on.
It's difficult enough to repair something by remote control as it is.

 

[gmwgj]

imxlink.exe ub2fb.img nnglow2.img

U-Boot 2009.08-00731-g2f1881a (Oct 19 2021 - 22:20:11)
CPU: Freescale i.MX6 family TO0.0 at 792 MHz
Thermal sensor with ratio = 181
Temperature:   36 C, calibration data 0x57d5025f
mx6q pll1: 792MHz
mx6q pll2: 528MHz
mx6q pll3: 480MHz
mx6q pll8: 50MHz
ipg clock     : 66000000Hz
ipg per clock : 24000000Hz
uart clock    : 80000000Hz
cspi clock    : 60000000Hz
ahb clock     : 132000000Hz
axi clock   : 198000000Hz
emi_slow clock: 99000000Hz
ddr clock     : 396000000Hz
usdhc1 clock  : 198000000Hz
usdhc2 clock  : 198000000Hz
usdhc3 clock  : 198000000Hz
usdhc4 clock  : 198000000Hz
Board: MX6SoloLite-NTX:[ WDOG ]
Boot Device: MMC
I2C:   ready
DRAM:  512 MB
MMC:   ram p=80000000,size=536870912
mmc0(part 0) is current device
MMC read: dev # 0, block # 1023, count 1 ... 1 blocks read: OK
MMC read: dev # 0, block # 1024, count 1 ... 1 blocks read: OK
FSL_USDHC: 0,FSL_USDHC: 1,FSL_USDHC: 2
RC5T619_disable_NOE(): done
hw_anadig_reg_core=7c3e1f
MMC read: dev # 0, block # 34815, count 1 ... 1 blocks read: OK
MMC read: dev # 0, block # 34816, count 1516 ... 1516 blocks read: OK
*** Warning - bad CRC or MMC, using default environment
In:    serial
Out:   serial
Err:   serial
ntx_hw_late_init()
MMC read: dev # 0, block # 1, count 1 ... 1 blocks read: OK
NTXSN:""
ntx_detect_usb_plugin():Charge detecting .....set 500mA for SDP (0x08)(3)
ntx_config_fastboot_layout():8 binaries partition added
ntx_config_fastboot_layout: get partition:system fail !!
ntx_config_fastboot_layout: get partition:data fail !!
ntx_config_fastboot_layout: get partition:cache fail !!
ntx_config_fastboot_layout: get partition:boot fail !!
ntx_config_fastboot_layout: get partition:recovery fail !!
ntx_config_fastboot_layout: get partition:vendor fail !!
ntx_config_fastboot_layout: get partition:misc fail !!
ntx_config_fastboot_layout():7 mbr partition added
Detecting Magic keys for recovery ...0 0
Checking for recovery command file...
** Bad partition 6 **
mmc0(part 0) is current device
## Unknown partition table
misc partition not found!!
misc partition not found!!
Net:   No ethernet found.
microp version=0xe711
ptn 0 name='mbr' start=0 len=1
ptn 1 name='sn' start=1 len=1
ptn 2 name='bootloader' start=2 len=1022
ptn 3 name='hwcfg' start=1024 len=2
ptn 4 name='ntxfw' start=1030 len=256
ptn 5 name='waveform' start=14336 len=20480
ptn 6 name='logo' start=34816 len=4096
ptn 7 name='bootenv' start=1536 len=510
fastboot_quick(0) enter
fastboot is in init......flash target is MMC:0
USB Mini b cable Connected!
Fastboot Cmd, len=14, getvar:product
Fastboot Cmd, len=14, getvar:version
Fastboot Cmd, len=17, download:00596000
Fastboot is receiveing data...
receive 5%
receive 11%
receive 16%
receive 22%
receive 27%
receive 33%
receive 39%
receive 44%
receive 50%
receive 55%
receive 61%
receive 67%
receive 72%
receive 78%
receive 83%
receive 89%
receive 100%
Fastboot Cmd, len=4, boot
Booting kernel...
RC5T619 read battery temperature 1109mV (0x719).
 hwcfgp=9ffffe00,pcb=49,customer=0
ESDin=0,UPGKey=-1,PWRKey=0,USBin=0x1,BootESD=0,MenuKey=0
turning on FL
MMC read: dev # 0, block # 14335, count 1 ... 1 blocks read: OK
[WARNING] Binaries load sequence should Lo->Hi !
MMC read: dev # 0, block # 14336, count 9185 ... 9185 blocks read: OK
MMC read: dev # 0, block # 1029, count 1 ... 1 blocks read: OK
binary magic @ sector no. 1030 not found !
"ntxfw" not exist !!
Reserved 1M for ram console
Kernel RAM visiable size=505M->505M
hwcfg rootfstype : 2
hwcfg partition type : 10
kernel   @ 80808000 (3722544)
ramdisk  @ 81800000 (2130458)
kernel cmdline:
        use uboot command line:
        console=ttymxc0,115200 init=/init androidboot.console=ttymxc0 video=mxcepdcfb:E060SCM,bpp=16 video=mxc_elcdif_fb:off no_console_suspend hwcfg_p=0x9ffffe00 hwcfg_sz=110 logo_p=0x9ff42600 logo_sz=776128 waveform_p=0x9fac6400 waveform_sz=4702424 ram_console_p=0x9f9c6400 mem=505M boot_port=3 androidboot.serialno= androidboot.hardware=E60QD0 rootfstype=ext4 root=/dev/mmcblk0p1
Starting kernel ...
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 3.0.35-06562-g469708a ([email protected]) (gcc version 4.6.x-google 20120106 (prerelease) (GCC) ) #2 PREEMPT Mon Aug 24 23:26:07 PDT 2015
CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: Freescale i.MX 6SoloLite NTX Board
Memory policy: ECC disabled, Data cache writeback
CPU identified as i.MX6SoloLite, unknown revision
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 120078
Kernel command line: console=ttymxc0,115200 init=/init androidboot.console=ttymxc0 video=mxcepdcfb:E060SCM,bpp=16 video=mxc_elcdif_fb:off no_console_suspend hwcfg_p=0x9ffffe00 hwcfg_sz=110 logo_p=0x9ff42600 logo_sz=776128 waveform_p=0x9fac6400 waveform_sz=4702424 ram_console_p=0x9f9c6400 mem=505M boot_port=3 androidboot.serialno= androidboot.hardware=E60QD0 rootfstype=ext4 root=/dev/mmcblk0p1
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 473MB = 473MB total
Memory: 469228k/469228k available, 47892k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xf4600000 - 0xffe00000   ( 184 MB)
    vmalloc : 0xe0000000 - 0xf2000000   ( 288 MB)
    lowmem  : 0xc0000000 - 0xdf900000   ( 505 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .init : 0xc0008000 - 0xc0037000   ( 188 kB)
      .text : 0xc0037000 - 0xc06d0ae8   (6759 kB)
      .data : 0xc06d2000 - 0xc0720340   ( 313 kB)
       .bss : 0xc0720364 - 0xc084ccd8   (1203 kB)
Preemptible hierarchical RCU implementation.
NR_IRQS:624
MXC GPIO hardware
sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
arm_max_freq=1GHz
MXC_Early serial console at MMIO 0x2020000 (options '115200')
bootconsole [ttymxc0] enabled
Calibrating delay loop... 1581.05 BogoMIPS (lpj=7905280)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
print_constraints: dummy:
NET: Registered protocol family 16
print_constraints: vddpu: 725 <--> 1300 mV at 700 mV fast normal
print_constraints: vddcore: 725 <--> 1300 mV at 1475 mV fast normal
print_constraints: vddsoc: 725 <--> 1300 mV at 1475 mV fast normal
print_constraints: vdd2p5: 2000 <--> 2775 mV at 2400 mV fast normal
print_constraints: vdd1p1: 800 <--> 1400 mV at 1100 mV fast normal
print_constraints: vdd3p0: 2625 <--> 3400 mV at 3000 mV fast normal
_parse_cmdline():cp cmdline=console=ttymxc0,115200 init=/init androidboot.console=ttymxc0 video=mxcepdcfb:E060SCM,bpp=16 video=mxc_elcdif_fb:off no_console_suspend hwcfg_p=0x9ffffe00 hwcfg_sz=110 logo_p=0x9ff42600 logo_sz=776128 waveform_p=0x9fac6400 waveform_sz=4702424 ram_console_p=0x9f9c6400 mem=505M boot_port=3 androidboot.serialno= androidboot.hardware=E60QD0 rootfstype=ext4 root=/dev/mmcblk0p1
hwcfg_size_setup() hwcfg_szie=110
hwcfg_p_setup() hwcfg_p=9ffffe00,vaddr=e000ee00,size=110,pcb=0x31
boot_port_setup() boot_port=3
Wifi / BT power control 0
[_ntx_wifi_power_ctrl-3144] not registered.
_ntx_wifi_power_ctrl() end.
[mx6_ntx_init-3776] irq_alloc_descs return 160 for 70 RICOH61x
ram_console: got buffer at 9f9c6400, size 100000
ram_console: uncorrectable error in header
ram_console: no valid data in buffer (sig = 0xdf7f73ef)
console [ram-1] enabled
mx6_ntx_init(): "bcm4329_wlan" device registed !!
hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
hw-breakpoint: 1 breakpoint(s) reserved for watchpoint single-step.
hw-breakpoint: maximum watchpoint size is 4 bytes.
L310 cache controller enabled
l2x0: 16 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x32030000, Cache size: 262144 B
bio: create slab <bio-0> at 0
PMU: ricoh61x_regulator_init
PMIC Light driver loading...
PMIC ADC start probe
PMIC Light successfully loaded
PMU: ricoh61x_i2c_init:
i2c-core: driver [ricoh619] using legacy suspend method
i2c-core: driver [ricoh619] using legacy resume method
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Freescale USB OTG Driver loaded, $Revision: 1.55 $
PMU: ricoh61x_i2c_probe:
PMU: ricoh61x_irq_init: g_full_flag: 0, CHGSTS1: 0x00
add wake up source irq 106
[__ricoh61x_set_s_voltage-151] at 950000uv suspend
print_constraints: RICOH619_DC1: at 1400 mV normal standby
print_constraints: RICOH619_DC2: at 3300 mV normal standby
[__ricoh61x_set_s_voltage-151] at 950000uv suspend
print_constraints: RICOH619_DC3: 950 <--> 1425 mV at 1425 mV normal standby
print_constraints: RICOH619_DC4: at 1200 mV normal standby
print_constraints: RICOH619_DC5: at 1800 mV normal standby
print_constraints: RICOH619_LDO1: at 3300 mV normal standby
print_constraints: RICOH619_LDO2: at 3300 mV normal standby
print_constraints: RICOH619_LDO3: at 1200 mV normal standby
print_constraints: RICOH619_LDO4: at 1200 mV normal standby
print_constraints: RICOH619_LDO5: at 3300 mV normal standby
print_constraints: RICOH619_LDO6: at 600 mV normal standby
print_constraints: RICOH619_LDO7: at 3300 mV normal standby
print_constraints: RICOH619_LDO8: at 1800 mV normal standby
print_constraints: RICOH619_LDO9: at 1200 mV normal standby
print_constraints: RICOH619_LDO10: at 1400 mV normal standby
print_constraints: RICOH619_LDORTC1: at 3300 mV normal standby
print_constraints: RICOH619_LDORTC2: at 3300 mV normal standby
MIPI CSI2 driver module loaded
Advanced Linux Sound Architecture Driver Version 1.0.24.
cfg80211: Calling CRDA to update world regulatory domain
i2c-core: driver [max17135] using legacy suspend method
i2c-core: driver [max17135] using legacy resume method
PMU RTC: ricoh61x_rtc_probe, ricoh61x driver run at 24H-mode
PMU RTC: we never using periodic function and interrupt
ricoh61x_rtc_Pon_get_clr, PON=1 -- CTRL2=0x20
PMU: ricoh61x_rtc_alarm_enable :0
PMU: ricoh61x_rtc_probe register rtc device
PMU: ricoh61x_rtc_read_alarm
rtc_ricoh619 rtc_ricoh619.0: PMU: read alarm: 1/1/2011 0:0:0 *****
rtc_ricoh619 rtc_ricoh619.0: rtc core: registered rtc_ricoh619 as rtc0
[ricoh61x_irq_sync_unlock-275] set 0xAE to 0x60
PMU: ricoh61x_rtc_alarm_enable :0
RICOH61x RTC Register Success
Switching to clocksource mxc_timer1
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 2080K
etb: probe of etb failed with error -2
etm: probe of etm.0 failed with error -2
Static Power Management for Freescale i.MX6
wait mode is enabled for i.MX6
cpaddr = 0 suspend_iram_base=f2900000
PM driver module loaded
EMMC DSE set to 48 ohm
IMX usb wakeup probe
the wakeup pdata is 0xda0f0660
add wake up source irq 75
cpu regulator mode:ldo_enable
i.MXC CPU frequency driver
ashmem: initialized
fuse init (API version 7.16)
msgmni has been set to 920
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
drivers/video/mxc/mxc_epdc_fb.c(6726):EPD 1448x1072
-> requested panel string E060SCM
-> epdc modes[0] - E60SC8
-> epdc modes[1] - E60_V110
-> epdc modes[2] - E60XC5
-> epdc modes[3] - E60XC1
-> epdc modes[4] - ED050XXXX
-> epdc modes[5] - ED068TG1
-> epdc modes[6] - PENG060D
-> epdc modes[7] - EF133UT1SCE
-> epdc modes[8] - E60SCQ
waveform_size_setup() wf_size=4702424
***_MemoryRequest:171: request memory region! addr=0x9fac6400, len=4702424***
waveform_p_setup() wf_p=9fac6400,vaddr=e0800400,size=4702424
logo_size_setup() logo_szie=776128
***_MemoryRequest:171: request memory region! addr=0x9ff42600, len=776128***
logo_p_setup() logo_p=9ff42600,vaddr=e0100600,size=776128
[epdc_firmware_work_func]:fw p=e0800400,size=4702424,[email protected],pdata=da0f7e80
drivers/video/mxc/mxc_epdc_fb.c(6218):EPD 1448x1072
imx-sdma imx-sdma: loaded firmware 1.1
imx_epdc_fb imx_epdc_fb:  --- Extra Waveform Data length: 29 bytes---
imx_epdc_fb imx_epdc_fb:      Extra Waveform Data: 320_R114_AF8801_ED060KH3U1_TC
fake_s1d13522_parse_epd_cmdline : epd cmdline parse already done .
imx-sdma imx-sdma: initialized
[email protected] ,addr=0x68,name=tps65185-1
drivers/video/mxc/lk_tps65185.c(1083): EP_3V3 ON/OFF control enabled !EP3V3 OFF ticks=400
TPS65185 versions : major=0x1,minor=0x2,version=0x5,RevID=0x65
[tps65185_init-1135] gpio_to_irq ()
TPS65185 temprature data = 0x1d,29
Serial: IMX driver
imx-uart.0: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX
console [ttymxc0] enabled, bootconsole disabled
console [ttymxc0] enabled, bootconsole disabled
brd: module loaded
loop: module loaded
[msp430_i2c_probe-1632] firmware version E711
msp430_i2c_probe, regulator found
add wake up source irq 103
i2c-core: driver [msp430] using legacy suspend method
i2c-core: driver [msp430] using legacy resume method
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPTP driver version 0.8.5
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
fsl-ehci fsl-ehci.0: irq 75, io base 0x02184000
fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
usbcore: registered new interface driver cdc_acm
cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
USB Serial support registered for Qualcomm USB modem
usbcore: registered new interface driver qcserial
ARC USBOTG Device Controller driver (1 August 2005)
my_batt_ext_power_changed!
It is not usb supply!
adb_setup
android_usb gadget: Mass Storage Function, version: 2009/09/11
android_usb gadget: Number of LUNs=1
 lun0: LUN: removable file: (no medium)
Gadget Android: controller 'fsl-usb2-udc' not recognized
android_usb gadget: android_usb ready
Suspend udc for OTG auto detect
USB Host suspend begins
will suspend roothub and its children
ehci_fsl_bus_suspend begins, DR
ehci_fsl_bus_suspend ends, DR
host suspend ends
USB Gadget resume begins
fsl_udc_resume, Wait for wakeup thread finishes
dr_controller_run: udc out low power mode
USB Gadget resume ends
fsl-usb2-udc: bind to driver android_usb
mousedev: PS/2 mouse device common for all mice
input: gpio-keys as /devices/platform/gpio-keys/input/input0
i2c-core: driver [zforce-ir-touch] using legacy suspend method
i2c-core: driver [zforce-ir-touch] using legacy resume method
[elan] __hello_packet_handler: hello packet 55:55:55:55:ff:ff:ff:ff
[__elan_touch_init-301] firmware version 52 01 25 A1 (125A)
[__elan_touch_init-308] firmware ID 52 F2 57 11 (2571)
msp430_homepad_sensitivity_set(0x5)
[__elan_touch_init-338] boot code version  52 02 50 21
[__elan_touch_init-343] x resolution: 1515
[__elan_touch_init-348] y resolution: 2048
android_work: did not send uevent (0 0   (null))
[__elan_touch_calibration-270] set calibration done.
input: elan-touch as /devices/virtual/input/input1
cpufreq_interactive_input_connect: connect to elan-touch
elan ts starts in interrupt mode.
i2c-core: driver [elan-touch] using legacy suspend method
i2c-core: driver [elan-touch] using legacy resume method
i2c-core: driver [kl25] using legacy suspend method
i2c-core: driver [kl25] using legacy resume method
[Waltop]-waltop_I2C_init: Waltop I2C Pen Driver (Built Aug 24 2015 @ 23:25:28)
i2c-core: driver [waltop_i2c] using legacy suspend method
i2c-core: driver [waltop_i2c] using legacy resume method
[Waltop]-waltop_I2C_init: Pen i2c driver add Success
using rtc device, rtc_ricoh619, for alarms
i2c /dev entries driver
android_work: sent uevent USB_STATE=CONNECTED
android_work: sent uevent USB_STATE=DISCONNECTED
Linux video capture interface: v2.00
PMU: ricoh61x_battery_init
PMU: ricoh61x_battery_probe : version is RICOH61x_BATTERY_VERSION: 2014.02.21 V3.1.0.0-Solution1 2015/02/09
ricoh61x_battery_probe type_n=0,temp is 1
ricoh61x_battery_probe info->num=0,temp is 1
PMU FG_RESET : ricoh61x_init_battery : initial pswr = 95
PMU : ricoh61x_init_battery : POWER off history 0x0a is 0x01
PMU : ricoh61x_init_battery : Long power on key press
PMU : ricoh61x_init_battery : POWER control function 0x0d is 0x00
PMU: ricoh61x_set_OCV_table : 00% voltage = 3579900 uV
PMU: ricoh61x_set_OCV_table : 10% voltage = 3687400 uV
PMU: ricoh61x_set_OCV_table : 20% voltage = 3743500 uV
PMU: ricoh61x_set_OCV_table : 30% voltage = 3768000 uV
PMU: ricoh61x_set_OCV_table : 40% voltage = 3788700 uV
PMU: ricoh61x_set_OCV_table : 50% voltage = 3818000 uV
PMU: ricoh61x_set_OCV_table : 60% voltage = 3879100 uV
PMU: ricoh61x_set_OCV_table : 70% voltage = 3941300 uV
PMU: ricoh61x_set_OCV_table : 80% voltage = 4004800 uV
PMU: ricoh61x_set_OCV_table : 90% voltage = 4083000 uV
PMU: ricoh61x_set_OCV_table : 100% voltage = 4183100 uV
PMU : ricoh61x_set_OCV_table : target_vsys is 3012 target_ibat is 302
PMU : ricoh61x_scaling_OCV_table : setting value of cuttoff_vol(3092) is out of range(3579900)
PMU : ricoh61x_scaling_OCV_table : new table
PMU : ricoh61x_scaling_OCV_table : ocv_table 0 is 35788 v
PMU : ricoh61x_scaling_OCV_table : ocv_table 1 is 36850 v
PMU : ricoh61x_scaling_OCV_table : ocv_table 2 is 37411 v
PMU : ricoh61x_scaling_OCV_table : ocv_table 3 is 37668 v
PMU : ricoh61x_scaling_OCV_table : ocv_table 4 is 37875 v
PMU : ricoh61x_scaling_OCV_table : ocv_table 5 is 38168 v
PMU : ricoh61x_scaling_OCV_table : ocv_table 6 is 38779 v
PMU : ricoh61x_scaling_OCV_table : ocv_table 7 is 39389 v
PMU : ricoh61x_scaling_OCV_table : ocv_table 8 is 40037 v
PMU : ricoh61x_scaling_OCV_table : ocv_table 9 is 40818 v
PMU : ricoh61x_scaling_OCV_table : ocv_table 10 is 41819 v
android_work: sent uevent USB_STATE=CONNECTED
type 2, status : 0x08
type 3, status : 0x08
type 2, status : 0x08
type 0, status : 0x08
type 3, status : 0x08
type 2, status : 0x08
type 0, status : 0x08
type 3, status : 0x08
android_work: sent uevent USB_STATE=DISCONNECTED
PMU : ricoh61x_init_charger : GCHGDET (0xDA) is 0x8
PMU : ricoh61x_init_charger : after CHGISET_REG (0xb8) is 0x4 info->ch_ichg is 0xff info->ch_icchg is 0x0
PMU : ricoh61x_init_charger : before BATSET1_REG (0xba) is 0x88 info->ch_vbatovset is 0xff
PMU : ricoh61x_init_charger : after BATSET1_REG (0xba) is 0x88 info->ch_vbatovset is 0xff
PMU : ricoh61x_init_charger : before BATSET2_REG (0xbb) is 0x31 info->ch_vrchg is 0xff info->ch_vfchg is 0xff
PMU : ricoh61x_init_charger : test test val 48, val2 3 vfchg 4200
PMU : ricoh61x_init_charger : test test val 0, val2 0 icchg 50
PMU : ricoh61x_init_charger : 100 min 4127000, 100 max 4251000 vfchg 4200 icchg 50 rbat 211
PMU: ricoh61x_init_fgsoca : * 00% voltage = 3578700 uV
PMU: ricoh61x_init_fgsoca : * 10% voltage = 3684900 uV
PMU: ricoh61x_init_fgsoca : * 20% voltage = 3741100 uV
PMU: ricoh61x_init_fgsoca : * 30% voltage = 3766700 uV
PMU: ricoh61x_init_fgsoca : * 40% voltage = 3787500 uV
PMU: ricoh61x_init_fgsoca : * 50% voltage = 3816800 uV
PMU: ricoh61x_init_fgsoca : * 60% voltage = 3877800 uV
PMU: ricoh61x_init_fgsoca : * 70% voltage = 3938900 uV
PMU: ricoh61x_init_fgsoca : * 80% voltage = 4003600 uV
PMU: ricoh61x_init_fgsoca : * 90% voltage = 4081800 uV
PMU: ricoh61x_init_fgsoca : * 100% voltage = 4181900 uV
PMU: ricoh61x_init_fgsoca : * Rbat = 211 mOhm   n_cap = 1510 mAH
i2c-core: driver [mag3110] using legacy suspend method
i2c-core: driver [mag3110] using legacy resume method
imx2-wdt imx2-wdt.0: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=1)
android_work: sent uevent USB_STATE=CONNECTED
android_work: sent uevent USB_STATE=DISCONNECTED
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: [email protected]
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
mmc0: no vmmc regulator found
mmc0: SDHCI controller on platform [sdhci-esdhc-imx.3] using DMA
sdhci sdhci-esdhc-imx.1: no write-protect pin available!
mmc1: no vmmc regulator found
mmc1: SDHCI controller on platform [sdhci-esdhc-imx.1] using DMA
[ntx_register_wifi_cd-2989] register g_cd_irq
mmc2: no vmmc regulator found
mmc2: SDHCI controller on platform [sdhci-esdhc-imx.2] using DMA
Galcore version 4.6.9.9754
USB Gadget resume begins
fsl_udc_resume, Wait for wakeup thread finishes
revserved_memory_account:viv_gpu registerd
Thermal calibration data is 0x57d5025f
Thermal sensor with ratio = 181
Anatop Thermal registered as thermal_zone0
anatop_thermal_probe: default cooling device is cpufreq!
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
logger: created 256K log 'log_main'
logger: created 256K log 'log_events'
logger: created 256K log 'log_radio'
logger: created 256K log 'log_system'
usbcore: registered new interface driver snd-usb-audio
mmc0: new high speed DDR MMC card at address 0001
mmcblk0: mmc0:0001 SEM04G 3.68 GiB
Initialize HDMI-audio failed. Load HDMI-video first!
ALSA device list:
 mmcblk0: unknown partition table
  No soundcards found.
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (7364 buckets, 29456 max)
ctnetlink v0.93: registering with nfnetlink.
NF_TPROXY: Transparent proxy support initialized, version 4.1.0
NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
xt_time: kernel timezone is -0000
IPv4 over IPv4 tunneling driver
GRE over IPv4 demultiplexor driver
android_work: sent uevent USB_STATE=CONNECTED
ip_tables: (C) 2000-2006 Netfilter Core Team
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 10
android_work: sent uevent USB_STATE=DISCONNECTED
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
L2TP IP encapsulation support (L2TPv3)
L2TP netlink interface
L2TP ethernet pseudowire support (L2TPv3)
lib80211: common routines for IEEE802.11 drivers
lib80211_crypt: registered algorithm 'NULL'
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
DDR type is LPDDR2
Bus freq driver module loaded
Bus freq driver Enabled
DVFS driver module loaded
rtc_ricoh619 rtc_ricoh619.0: setting system clock to 2012-01-01 00:41:14 UTC (1325378474)
Freeing init memory: 188K
android_work: sent uevent USB_STATE=CONNECTED
android_work: sent uevent USB_STATE=DISCONNECTED
drawing logo begin ...
[k_wait_update_complete]waitupdate ret=-22,4294937585->4294937585
android_work: sent uevent USB_STATE=CONNECTED
[k_wait_update_complete]waitupdate ret=455,4294937657->4294937702
[PROGRESS_BAR-3065] No progess ...
init (1): /proc/1/oom_adj is deprecated, please use /proc/1/oom_score_adj instead.
type 2, status : 0x08
type 3, status : 0x08
type 0, status : 0x08
init: /dev/hw_random not found
init: Battery Capacity [0] USB [1] ADC [0x3ff]
init: /dev/hw_random not found
init: Unable to open persistent property directory /data/property errno: 2
init: property 'ro.serialno' doesn't exist while expanding '${ro.serialno}'
# init: cannot expand '${ro.serialno}' while writing to '/sys/class/android_usb/android0/iSerial'
init: Unable to write persistent property to temp file /data/property/.temp.X2ArX9 errno: 2
init: property 'sys.powerctl' doesn't exist while expanding '${sys.powerctl}'
init: powerctl: cannot expand '${sys.powerctl}'
init: property 'sys.sysctl.extra_free_kbytes' doesn't exist while expanding '${sys.sysctl.extra_free_kbytes}'
init: cannot expand '${sys.sysctl.extra_free_kbytes}' while writing to '/proc/sys/vm/extra_free_kbytes'
android_usb: already disabled
adb_bind_config
adb_open
android_work: sent uevent USB_STATE=DISCONNECTED
android_work: sent uevent USB_STATE=CONNECTED
android_work: sent uevent USB_STATE=DISCONNECTED
android_work: sent uevent USB_STATE=CONNECTED
android_usb gadget: high speed config #1: android
android_work: sent uevent USB_STATE=CONFIGURED
PMU: cc_sum = 158: cc_cap_res= 31: cc_cap_mas = -637288656
PMU: cc_cap_offset= -31:
PMU: ricoh61x_displayed_work : error case cc delta is 0mA, poffDSOC is 9500, RSOC is 9600n
PMU : set_current_time2register : second is 1325378479, hour is 368160
PMU: check_charge_status_2 g_full_flag=1 but OCV is low
PMU: cc_sum = 0: cc_cap_res= 0: cc_cap_mas = -637288748
PMU: cc_cap_offset= -31:
PMU : set_current_time2register : second is 1325378479, hour is 368160
PMU:STATUS= 7: IBAT= -4: VSYS= 4329000: VBAT= 4128200: DSOC= 9500: RSOC= 9600: cc_delta=0: rrf= 1

 

[Renate]

Doesn't the screen show anything? Do you have ADB?

 

[gmwgj]

Adb connected.
Nook Screen Show Neo Noogie logo all the time.

 

[gmwgj]

I restored Patition Table and executed these command correctly, but Nook show Neo Noogie Logo all the time .
C:\>fastboot flash recovery nnglow2.img
C:\>fastboot flash misc misc-rec.img
C:\>fastboot reboot



Patitions
ptn 0 name='mbr' start=0 len=1
ptn 1 name='sn' start=1 len=1
ptn 2 name='bootloader' start=2 len=1022
ptn 3 name='hwcfg' start=1024 len=2
ptn 4 name='waveform' start=14336 len=20480
ptn 5 name='logo' start=34816 len=4096
ptn 6 name='bootenv' start=1536 len=510
ptn 7 name='system' start=106496 len=786416
ptn 8 name='data' start=1710017 len=5990459
ptn 9 name='cache' start=894960 len=786416
ptn 10 name='boot' start=2048 len=12224
ptn 11 name='recovery' start=38912 len=65536
ptn 12 name='vendor' start=1683424 len=16368
ptn 13 name='misc' start=1701840 len=8176
fastboot is in init......flash target is MMC:0

 

[Renate]

C:\>fastboot erase misc

 

[gmwgj]

C:\>fastboot erase misc
Fastboot Cmd, len=10, erase:misc
Not support command:erase:misc

 

[Renate]

C:\>fastboot flash misc misc-empty.img

 

[gmwgj]

fastboot flash misc misc-empty.img

Fastboot Cmd, len=10, flash:misc
Init MMC0(misc)...
mmc0(part 0) is current device
MMC0(misc) init done
Writing MMC0(misc), 1 blocks...
MMC write: dev # 0, block # 1701840, count 1 ... 1 blocks write: OK
MMC0(misc) write done
Fastboot write OK, send OKAY...

 

[Renate]

Okay and reset?

 

[gmwgj]

Nook can't boot up ,just show Neo Noogie Logo all the time .

 

[Renate]

"Can't boot up" = in bootloader? in fastboot? in nothing?
You do have an attached UART. Can't you tell what's going on (without pasting 1000 lines)?

C:\>imxlink.exe ub2fb.img
C:\>fastboot flash misc misc-rec.img
C:\>fastboot reboot
C:\>adb push ub2.img /cache
(if /cache doesn't work, mount something or push it to / or wherever)
C:\>adb shell
# dd if=ub2.img of=/dev/block/mmcblk0 seek=2
# dd if=/dev/zero of=/dev/block/mmcblk0p8
(an error here is to be expected)
# reboot

 

[gmwgj]

C:\>imxlink.exe ub2fb.img
C:\>fastboot flash misc misc-rec.img
C:\>fastboot reboot
Above command can executed correctly. Other command can't executed, because can't load adb mode currently.
prompt:error: no devices found

 

[gmwgj]

I use this command ,other command can executed.
C:\>imxlink.exe ub2fb.img nnglow2.img

fastboot flash misc misc-rec.img
waiting for device

C:\>adb push ub2.img /cache
1192 KB/s 232048 bytes in 0.190s

adb shell
#
# dd if:ub2 . img of:/deu/block/mmcbik0 seek:2
dd: can't open 'ub2 . img' : No such file or directory

# dd if:/deu/zero of:/deu/block/mmcbik0p8
8177+0 records in
8176+0 records out
4186112 bgtes (40MB) copied. 0356296 seconds. 11 2MB/S

 

[Renate]

Sigh. You pushed ub2.img
Where did it go?
If there was no /cache dir it would have named it cache.

# ls -l /cache

If it's a dir, look inside if it's a file then it's ub2.img

 

[gmwgj]

# ls -l /cache
-rw-rw-rw- 1 0 0 232048 sep 16 2022 <-[0;0m/cache<-[0m

 

[Renate]

So, either rename it or don't.

# mv cache ub2.img
# dd if=ub2.img of=/dev/block/mmcblk0 seek=2