I tried with a clear case. Does not look too bad. I may try again with closer and straighter cuts.
Oneplus 8T (Cyberpunk Edition)
- Thread starter OniAraAra
- Start date
When flashing these files, is the phone itself formatted? In the sense that it will be necessary to restore the content?
Hi guyz, I need help with my device.
I bought a version with HydrogenOS (as i remember 0.1.2) and tryed to flash it on OxygenOS.
Last thing I done was downloading last firmware for 8t via OxygenUpdater OnePlus8TOxygen_15.E.23_OTA_0230_all_2102011823_d38dd558655966a and flashed it throw Setting > Wheel > Local
This led to a bootloop and I lost possibility to recover, couz recovery mode is no longer load properly ( I see just a black screen without options)
Before that, I unlocked bootloader and tried to do MSM flashing using KB05BA builds from this post https://forum.xda-developers.com/t/...l-to-restore-your-device-to-oxygenos.4180837/
I wasn't able to do that because of Param Preloader issue, wich I face each time. (Tryed different ports, cables, amd and intel, drivers, all steps from this article https://www.droidwin.com/fix-stuck-in-param-preload-error-msm-download-tool/)
After that I tried to flash phone by downloading firmware in the root section and using phone settings. In that way I tried KB05BA Europe 11.0.4.5 and 11.0.5.6 from this post https://forum.xda-developers.com/t/...po-of-oxygen-os-builds.4193183/#post-83971385 but after flashing I recieved a bootloop as well. Hopefully the recavery mode was available.
Now I don't know what to do.
I though to use TWRP, but have some concern about it.
Is TWRP for 8t fit to CP77 edition?
Will I be able to stock recover from it?
Right now I have a brick with unlocked bootloader (((
Could anybody guide me throw that sheet)
Thanks in advance.
I bought a version with HydrogenOS (as i remember 0.1.2) and tryed to flash it on OxygenOS.
Last thing I done was downloading last firmware for 8t via OxygenUpdater OnePlus8TOxygen_15.E.23_OTA_0230_all_2102011823_d38dd558655966a and flashed it throw Setting > Wheel > Local
This led to a bootloop and I lost possibility to recover, couz recovery mode is no longer load properly ( I see just a black screen without options)
Before that, I unlocked bootloader and tried to do MSM flashing using KB05BA builds from this post https://forum.xda-developers.com/t/...l-to-restore-your-device-to-oxygenos.4180837/
I wasn't able to do that because of Param Preloader issue, wich I face each time. (Tryed different ports, cables, amd and intel, drivers, all steps from this article https://www.droidwin.com/fix-stuck-in-param-preload-error-msm-download-tool/)
After that I tried to flash phone by downloading firmware in the root section and using phone settings. In that way I tried KB05BA Europe 11.0.4.5 and 11.0.5.6 from this post https://forum.xda-developers.com/t/...po-of-oxygen-os-builds.4193183/#post-83971385 but after flashing I recieved a bootloop as well. Hopefully the recavery mode was available.
Now I don't know what to do.
I though to use TWRP, but have some concern about it.
Is TWRP for 8t fit to CP77 edition?
Will I be able to stock recover from it?
Right now I have a brick with unlocked bootloader (((
Could anybody guide me throw that sheet)
Thanks in advance.
Last edited:
This will likely get you back to stock.
tradingshenzhen.com
Also don't use Oxygen Updater. I tried it early on and it only caused me wasted time and problems.
I am currently on OOS, with all the CP goods, with no problems at all. Also was able to update last night with the latest security OTA and nothing was lost.
Reach out if you need help but read through this entire thread as there is a lot of good info here which will help you work out the best way to manage your new device.
TradingShenzhen - China Smartphones and Gadgets with Top Service
TradingShenzhen sells high quality Smartphones, Tablets and Accessories from China. We offer TOP Support and a AWESOME prices!
Also don't use Oxygen Updater. I tried it early on and it only caused me wasted time and problems.
I am currently on OOS, with all the CP goods, with no problems at all. Also was able to update last night with the latest security OTA and nothing was lost.
Reach out if you need help but read through this entire thread as there is a lot of good info here which will help you work out the best way to manage your new device.
Attachments
Been a while since I replied to this thread. In my original post there is a guide on how to restore original HOS:
Oneplus 8T (Cyberpunk Edition) - HydrogenOS (Google Apps, Theme, OTA Updates!)
Originality/HydrogenOS If you have a Chinese Cyberpunk Edition phone with OxygenOS, you'll notice that the Cyberpunk theme/assets are missing, and OTA updates lead to a boot loop. This guide will tell you how to restore the phone to its original...
forum.xda-developers.com
Where'd you find one that fits? The market definitely seems to be short on cases, which makes sense. I'm still using the OEM, but a clear/silicone 8T might work.
Last edited:
Thank you very much for answering!Been a while since I replied to this thread. In my original post there is a guide on how to restore original HOS:
Oneplus 8T (Cyberpunk Edition) - HydrogenOS (Google Apps, Theme, OTA Updates!)
Originality/HydrogenOS If you have a Chinese Cyberpunk Edition phone with OxygenOS, you'll notice that the Cyberpunk theme/assets are missing, and OTA updates lead to a boot loop. This guide will tell you how to restore the phone to its original...
Where'd you find one that fits? The market definitely seems to be short on cases, which makes sense. I'm still using the OEM, but a clear/silicone 8T might work.
I tried this thread and some other with MSM using. I still think that MSM flashing is the best option but can not handle the problem with param preload error, I face it on two different laptops (AMD/Intel).
Does anybody know how it works in MSM..
Is it important if device bootloader is unlocked? (As I think, it does not as far as I saw the post, that after flashing phone relocked but who knows..)
May be someone can figure out what is happening by looking at log file..
May be internet speed is important while starting MSM?
May be it is possible to restore recovery mod somehow without MSM?
I do not know about the "param preload" error. Are you clicking "Run as Administrator" when you use the MSM tool? Did you extract the files properly? Have you made sure the device drivers are installed properly?
I do not believe the bootloader being unlocked matters. One thing I recall was that if the bootloader was unlocked, the device would wipe if you went to lock it again.
Sure, I run as admin.
Not sure about extracting and driveres, I'm already confused about different builds and drivers.
Is it important to have Android drivers correctly installed? or for MSM only Qualcome driver is required?
Thank you one more time for help and asistance, I will keep trying..
Attachments
You will want to install these drivers:
https://oneplususbdrivers.com/oneplus-8t-usb-driver-download/ (Oneplus)
https://androidfilehost.com/?fid=10763459528675593342 (Qualcomm)
Param preload means it isn't even getting to the point it has interfaced with your device. Make sure you follow the instructions here: https://forum.xda-developers.com/t/...ogenos-google-apps-theme-ota-updates.4199011/
(Under "Now make sure your phone is ready")
Last edited:
Thank you @OniAraAra and @gee.dunkin for your assistanse. The problem was with Qualcome driver. I tried different ways and in my case this post https://forums.oneplus.com/threads/...stuck-in-param-preload.1107124/#post-23007581 helped to fix param preload issue (work on intel, didn't try on amd).
Has anyone ever installed LinageOS on a Oneplus 8t Cyberpunk 2077 edition? Does that work?
Oneplus 8t Cyberpunk 2077 is KB2000. According to https://wiki.lineageos.org/devices/kebab/ it should work.
Oneplus 8t Cyberpunk 2077 is KB2000. According to https://wiki.lineageos.org/devices/kebab/ it should work.
At the moment i have OxygenOS on it. No OTA on that. So i need always to reinstall the whole phone for an update. But i need some apps (RSA for example) that can't be backupped. So i need to contact my company to give me new tokens.
HydrogenOS could work, but i need the OS it in German cos of the Google Assistant.
So i thought LinageOS would be the best fit.
In my Knowledge you cant OTA OxygenOS on Cyberpunk edition Phone. Only HydrogenOS.
So reinstalling with the every Security update is a must. Or am i wrong.
And no, has nothing to do with root. I don't even have root enabled.
I've had a Cyberpunk phone for a year now. It works on the European version. And there are no problems with updates. I went through everything in the loader, as previously discussed here. And now I have a normal OS , with themes and cyberpunk downloads
Top Liked Posts
-
There are no posts matching your filters.
-
6Update worked, however I need to highlight that 11.0.6.7 seems buggy to me (Stutter and other stuff)
Ok. So I got Global 11.0.6.7 update (OTA, incremental, around 500 MB size).
I updated and it worked (with all cyberpunk elements working and nothing changed).
Proof:
1) Cyberpunk8T Phone at Global OOS 11.0.5.6, and showing receiving new update under system-update:
2) Downloading Global OOS 11.0.6.7 update. Not full update, OTA, incremental, around 500 MB size:
3) Booting to Global OOS 11.0.6.7 after update and restart (it took a bit more time while booting, but worked at the end):
4) Showing updated phone to Global OOS 11.0.6.7 with cyberpunk elements intact:
So, I think flashing cyberpunk cust on both slots before, and then relocking and updating did work.
Below I will put the steps I took (please note that I tried this on Global version, no idea if EU or IN is the same).
Steps:
-1) If you received phone on HOS, do full local update into next HOS in order to ensure cust is flashed to the other slot. (preferably do 2 HOS full local updates just to ensure, recommended versions are OnePlus8T_Hydrogen_11.0.4.5_15.H.19_KB05, and OnePlus8T_Hydrogen_11.0.5.6_15.H.20_KB05. (another option would be to flash cust at this stage, but I am just stating what I did personally).
0) Use MSM tool to convert to Global OOS (check thread and forums for this step)
1) Now your cyberpunk 8T phone should be on OOS, and you have all cyberpunk elements working (this is important as it points that param flag for cyberpunk is active)
2) Unlock bootloader and root the phone (credit to @Kihara777 )
(for full info about this step check https://forum.xda-developers.com/t/...-for-oneplus-8t-devices.4198459/post-84055453 )
(for root info read https://forum.xda-developers.com/t/...in-eu-us-kb2000-kb2001-kb2003-kb2005.4178675/ )
2a) download this image: https://1drv.ms/u/s!AsJy8Rcn_wjLhLwuunq7W9seKfKT7Q?e=vTKQd0
2b) Use below commands in adb to push the cust images (google how to to adb commands).
2c) remove root and relock the bootloader (optional)Bash:adb push H19_OTA-oem_cust1-raw.img /sdcard/oc1.img (I actually unziped and copied the file to phone root through windows and renamed it to oc1.img, then did adb shell in cmd, and ran the below commands) su dd if=/sdcard/oc1.img of=/dev/block/bootdevice/by-name/oem_cust1_a dd if=/sdcard/oc1.img of=/dev/block/bootdevice/by-name/oem_cust1_b
[Alternative to step 2 if you cannot root][Tested by @lexcyn Thanks! ]
2) Unlock bootloader
2i) download this file: https://1drv.ms/u/s!AsJy8Rcn_wjLhLwtuwnEWCG4E1bNMQ?e=iRf5jm
2ii) flash through fastboot using these commands
2iii) relock the bootloader (optional)Bash:fastboot flash oem_cust1_a H19_OTA-oem_cust1-sparse.img fastboot flash oem_cust1_b H19_OTA-oem_cust1-sparse.img
3) After rebooting the phone, you should have all elements, and OTA incremental updates should not affect your cyberpunk elements or cause bootloop
This what have worked for me. Please familiarize yourself on how to unbrick just in case things did not go well.
Edit: fixed OOS 11.0.6.7 video link, and info about the adb commands
Edit2: flashing cust files using "dd" commands require the phone to be rooted. Alternatively, I added another flash commands using fastboot that not require root.5Hi,
So I have some good news (I think).
I was trying to flash OxygenOS (Global and EU) on my HydrogenOS (11.0.4.5) Cyberpunk8T. It ended me bricking my device. (Yes, I was fooling around with fastbootd >_<)
I went to this thread: https://forum.xda-developers.com/t/...l-to-restore-your-device-to-oxygenos.4180837/
and used the MSM tool @OniAraAra linked: https://androidfilehost.com/?w=files&flid=320230
I was able to get back to HOS (11.0.1.2). So this even downgraded my version, and I had all cyberpunk elements.
Then it hit me. I was trying to figure out how did the sellers flash the global OOS.... and most of xda members here state that their device came on "11.0.4.5.KB05AA ", and it had " SOME Cyberpunk things ".
So I went and did an MSM restore on my Cyberpunk8T HOS (11.0.1.2) to EU OOS 11.0.4.5 (from unbrick-tool thread above). Guess what it worked. I was able to boot to EU OOS 11.0.4.5.
Then right away, I did a local OTA upgrade using full package EU OOS 11.0.5.6 (https://forum.xda-developers.com/t/...l-to-restore-your-device-to-oxygenos.4180837/).
I booted to EU OOS 11.0.5.6, have cyberpunk boot animation, wallpapers, theme, icon pack, and sounds (basically everything, let me know if I should check something specific).
ps: I also heard that local upgrade is not available on Global or India OOS, thats why I tried it on EU. Not sure if one does EU MSM, then flash Global Full OTA locally if that might work or not.
Edit:
Uploading some videos (higher quality might some time to process)
4I received a Oneplus 8t (Cyberpunk Edition). The phone was supposed to have HydrogenOS as it is a Chinese phone. However, the vendor installed Global OxygenOS (KB05AA). After OTA updates, the phone wouldn't reboot and would get stuck on the Cyberpunk boot animation.
________________________________________
OxygenOS
I tried updating/restoring OxygenOS using the the MSM download tools here:
[OP8T][OOS KB05AA/BA/DA] Unbrick tool to restore your device to OxygenOS
Disclaimer: By attempting any of the processes...
forum.xda-developers.com
Pros: Google Apps and a Global ROM.
Cons: No OTA updates and no original Cyberpunk theme.
Best case scenario for OxygenOS users would be for Oneplus to fix the OTA updates for Cyberpunk phones. This would stop the bootloop problem people are having.
________________________________________
HydrogenOS
I have made a guide on how to restore HydrogenOS and add Google Apps:
Oneplus 8T (Cyberpunk Edition) - HydrogenOS (Google Apps, Theme, OTA Updates!)
Originality/HydrogenOS If you have a Chinese...
forum.xda-developers.com
Pros: Working OTA updates, the original Cyberpunk theme, and Google Apps!
Cons: A little bit of time and maintenance.
________________________________________
Overall I would highly recommend trying the HydrogenOS solution I've linked above. It works excellent for me, so I won't be pursuing a solution for OxygenOS unless things change. The guide I wrote and linked above should get anyone with a Cyberpunk phone on to HydrogenOS (with OTA updates, original theme, and Google Apps).
________________________________________
Bounty: Claimed by @Steve0007
Up to @Arr6 if he still wants to match my donation for the HydrogenOS solution.4
OK, so i finally got Oxygen OS 11.0.5.6.KB05AA (Global/USA) Running on my Oneplus 8T Cyberpunk edition (KB2000) with all the Cyberpunk goodies.. .
After all the previously mentioned attempts this is what got me through:
1.- MSM to Hydrogen OS using the link provided at OP.
2.-- Update Hydrogen OS to 11.0.5.6 using OTA update (incremental update directly on the phone).
3.- Once Hydrogen complete update to 11.0.5.6. Turn phone OFF.
4.- MSM to Oxygen OS to 11.0.1.2.
5.- Once Oxygen OS boot up, loaded 11.0.5.6.KB05AA FULL zip update (Provided on OnePlus website) to the phone's root directory.
6.- Perform a Local update through the "gear" icon under the system update section.
7.- voilà!!!
If you guys have any questions in regards of what i did, feel free to ask me.
Best of luck~4
Was just going to post this - the other command is if you are rooted.
This worked for me by the way, THANK YOU.
I was already on OOS 11.0.5.6 so I:
1) Unlocked bootloader
2) Flashed cust to a & b via fastboot
3) Relocked bootloader
4) Set up phone and restored from my OnePlus backup
5) Downloaded / installed OTA
Worked a treat and still have all of the Cyberpunk goodies!
[Edit] Also worth mentioning I don't have any of the lag issues on the new update, but probably since I wiped the phone and updated.
