[OP3/3T] Flashable Firmware+Modem ZIPs

[S4turno]

Status page: https://www.gsc-europa.eu/system-status/Constellation-Information

All satellites down :-s

 

[Herbert_Hamster]

Status page: https://www.gsc-europa.eu/system-status/Constellation-Information

All satellites down :-s

Apparently there is a problem with the Precise Timing Facility in Italy - the ground station that keeps all the satellite clocks in sync.

 

[hellcat50]

I have updated the thread to link a guide by @nvertigo67 (for those who have the device encrypted and want to keep their data after upgrading the firmware).

 

[Herbert_Hamster]

Seems that the Galileo constellation is functioning again but I can't see any of the satellites using the GPSTest app. Although the chipset is compatible, I suppose the firmware has not been updated to enable this.

 

[accuphase]

Seems that the Galileo constellation is functioning again but I can't see any of the satellites using the GPSTest app. Although the chipset is compatible, I suppose the firmware has not been updated to enable this.

Can't see any Galileo satellites too; only gps, glonass and beidou satellites

 

[wolke7]

Hi,

my OP3 has LineageOS 14.1 (Android 7.1.2) installed. Now looked forward to install LOS 16 (Android 9). I want a fresh installation. So i've made already complete TWRP-Backup and wiped all (data, system, sdcard, etc). During adb sideload from yesterday's LOS16.zip TWRP (3.3.1.-0) means i should upgrade my Firmware first. Which one should i take? The 5.0.8, or 9.0.4?

EDIT: It tells me: "Modem firmware from OxygenOS 9.0.2 or newer stock ROMs is prerequisite to be compatible with this build". OK, i need 9.0.4.

My question: may i flash the 9.0.4 over my old Firmware without problems? What is the safest way to do it? I found several instructions here on the board, but they differ... one says we should lock bootloader, the other not...

Thanks!
w7

 

[DanipunK1]

Hi,



my OP3 has LineageOS 14.1 (Android 7.1.2) installed. Now looked forward to install LOS 16. I want a fresh installation. So i've made already complete TWRP-Backup and wiped all (data, system, sdcard, etc). During adb sideload from yesterday's LOS16.zip TWRP means i should upgrade my Firmware first. Which one should i take? The 5.0.8, or 9.0.4?



EDIT: It tells me: "Modem firmware from OxygenOS 9.0.2 or newer stock ROMs is prerequisite to be compatible with this build". OK, i need 9.0.4.



My Question: may i flash the 9.0.4 over my old Firmware without problems? What is the best way to do it?



Thanks!

w7

In Los 16 op3 thread sure someone can help you better.
You can upgrade firm without doing anything else, flash it over and that's it

 

[Anghirrim]

Hi,

my OP3 has LineageOS 14.1 (Android 7.1.2) installed. Now looked forward to install LOS 16 (Android 9). I want a fresh installation. So i've made already complete TWRP-Backup and wiped all (data, system, sdcard, etc). During adb sideload from yesterday's LOS16.zip TWRP (3.3.1.-0) means i should upgrade my Firmware first. Which one should i take? The 5.0.8, or 9.0.4?

EDIT: It tells me: "Modem firmware from OxygenOS 9.0.2 or newer stock ROMs is prerequisite to be compatible with this build". OK, i need 9.0.4.

My question: may i flash the 9.0.4 over my old Firmware without problems? What is the safest way to do it? I found several instructions here on the board, but they differ... one says we should lock bootloader, the other not...

Thanks!
w7

Take care, flashing 9.0.4 firmware will entirely wipe your phone personnal data. The encryption uses a different process on Pie vs Oreo and the phone needs to erase all the personal data

 

[wolke7]

You can upgrade firm without doing anything else, flash it over and that's it

Thank You! It worked! I'm on LOS 16 now. Thanks! :good:

 

[hissan147]

Need Help

After installing this, I try to install ROM but due to error 7 I reboot the system and getting a black dead screen, Mobile is not getting on but is detected only in my PC's device manager. Any Solution?

 

[pitrus-]

After installing this, I try to install ROM but due to error 7 I reboot the system and getting a black dead screen, Mobile is not getting on but is detected only in my PC's device manager. Any Solution?

Are you sure you flashed the firmware for correct version of the 3, the firmware is different between the 3 and the 3t.

Skickat från min ONEPLUS A3003 via Tapatalk

 

[hissan147]

Are you sure you flashed the firmware for correct version of the 3, the firmware is different between the 3 and the 3t.

Skickat från min ONEPLUS A3003 via Tapatalk

I've installed OnePlus3T_4.0.3-FIRMWARE+MODEM-flashable.zip on 3.
So can I revert it?

---------- Post added at 11:40 AM ---------- Previous post was at 11:15 AM ----------

I've installed OnePlus3T_4.0.3-FIRMWARE+MODEM-flashable.zip on 3.
So can I revert it?

is this link helps me?
https://forum.xda-developers.com/oneplus-3/how-to/guide-mega-unbrick-guide-hard-bricked-t3405700

because my device is showing as Qualcomm 9008

 

[TNSMANI]

I've installed OnePlus3T_4.0.3-FIRMWARE+MODEM-flashable.zip on 3.
So can I revert it?

---------- Post added at 11:40 AM ---------- Previous post was at 11:15 AM ----------



is this link helps me?
https://forum.xda-developers.com/oneplus-3/how-to/guide-mega-unbrick-guide-hard-bricked-t3405700

because my device is showing as Qualcomm 9008

You have already bricked your phone. No further harm in trying that. May be the only way too!

EDIT: Try THIS also.

 

[hissan147]

You have already bricked your phone. No further harm in trying that. May be the only way too!

EDIT: Try THIS also.

Just tried, the phone is on but showing battery too low screen.

---------- Post added at 12:26 PM ---------- Previous post was at 12:22 PM ----------

Just tried, the phone is on but showing battery too low screen.

 

[DanipunK1]

Just tried, the phone is on but showing battery too low screen.

---------- Post added at 12:26 PM ---------- Previous post was at 12:22 PM ----------

Leave it charging for a while and then try the unbrick guide

 

[hissan147]

Just tried, the phone is on but showing battery too low screen.

---------- Post added at 12:26 PM ---------- Previous post was at 12:22 PM ----------

Now booting in fastboot mode only, can i use tool all in one (Recovery Flasher and Device Router)?

---------- Post added at 12:37 PM ---------- Previous post was at 12:34 PM ----------

Leave it charging for a while and then try the unbrick guide

after charged, the device was boot looping with an md5-checksum-failed red message and now I was just able to get into fastboot mode.

 

[DanipunK1]

Just tried, the phone is on but showing battery too low screen.



---------- Post added at 12:26 PM ---------- Previous post was at 12:22 PM ----------



Now booting in fastboot mode only, can i use tool all in one (Recovery Flasher and Device Router)?

---------- Post added at 12:37 PM ---------- Previous post was at 12:34 PM ----------





after charged, the device was boot looping with an md5-checksum-failed red message and now I was just able to get into fastboot mode.

Try the unbrick guide with the device in fastboot mode. I think it will work

 

[hissan147]

Try the unbrick guide with the device in fastboot mode. I think it will work

Can I use flash TWRP 3.3.1 OP3-3T with Automatic MD5 check option to go to Step 10 (Method 1)?

See this Image:
https://pasteboard.co/IqG8bOM.png

 

[DanipunK1]

Can I use flash TWRP 3.3.1 OP3-3T with Automatic MD5 check option to go to Step 10 (Method 1)?



See this Image:

https://pasteboard.co/IqG8bOM.png

Idk, you have a semibrick, you can try, and if no work, always you can try the method 2 step by step. This sure works.
I only have tested the method 2.

 

[hissan147]

Can I use flash TWRP 3.3.1 OP3-3T with Automatic MD5 check option to go to Step 10 (Method 1)?

See this Image:
https://pasteboard.co/IqG8bOM.png

Still Stuck on bootlooping screen, and in PC device manager instead of COM port, system showing Android bootloader interface.

---------- Post added at 05:28 PM ---------- Previous post was at 04:49 PM ----------

Idk, you have a semibrick, you can try, and if no work, always you can try the method 2 step by step. This sure works.
I only have tested the method 2.

ok let me try Method two.