Today i got my PDair ultra clear screen protector.
I got it because i needed a screen protector and i didn't find the spigen flex HD on amazon until a day after i placed my order, so i got this.
It comes in a small plastic bag, nothing fancy, inside you get ONE protector (i thought there would be at least 2 but i was wrong), a cleaning cloth, a "soft card" aka piece of plastic to squeeze out air bubbles and the obligatory instructions demonstrating how to apply on the iphone (the front "selling" image is also of an iphone
).
It's a dry application protector with two layers to peel off.
I should warn you so you don't make my mistake, the protector, once you remove the "step one" protective layer is EXTREMELY electrostatic. It picked up dust from the surrounding table like there was no tomorrow. So now i've got a bit of dust under my protector, but it's nothing serious, though it may bother some people.
It applies very nicely, this is my first screen protector ever and i managed to get it on the first time with no bubbles in the middle.
The sides and edges have some bubbles but i think thats just from the dust, or i didn't apply it correctly.
The protector itself is invisible, except for the edges of the plastic, and it's a bit harder to swipe now it's on, like it's a bit sticky.
Maybe that will wear off over time, will update this post if it does. It still collects fingerprints and smudges, but it's just a little bit better than without the protector.
It offers good protection, and fingernails do not leave a mark, neither does rubbing metal on it, though very sharp objects do leave a mark. (see last picture, i tested it with the sharp end of a screwdriver and pushed quite hard. It does scratch but the screen beneath is OK)
One more thing , it does not cover the whole screen, on the top and bottom there is about 3mm of glass to the edge, and on the sides it goes to the curved part. I use the case mate tough case so it does not bother me.
And thats it, pics below, any questions ask me and i will try to answer.
PICS:
I got it because i needed a screen protector and i didn't find the spigen flex HD on amazon until a day after i placed my order, so i got this.
It comes in a small plastic bag, nothing fancy, inside you get ONE protector (i thought there would be at least 2 but i was wrong), a cleaning cloth, a "soft card" aka piece of plastic to squeeze out air bubbles and the obligatory instructions demonstrating how to apply on the iphone (the front "selling" image is also of an iphone
). It's a dry application protector with two layers to peel off.
I should warn you so you don't make my mistake, the protector, once you remove the "step one" protective layer is EXTREMELY electrostatic. It picked up dust from the surrounding table like there was no tomorrow. So now i've got a bit of dust under my protector, but it's nothing serious, though it may bother some people.
It applies very nicely, this is my first screen protector ever and i managed to get it on the first time with no bubbles in the middle.
The sides and edges have some bubbles but i think thats just from the dust, or i didn't apply it correctly.
The protector itself is invisible, except for the edges of the plastic, and it's a bit harder to swipe now it's on, like it's a bit sticky.
Maybe that will wear off over time, will update this post if it does. It still collects fingerprints and smudges, but it's just a little bit better than without the protector.
It offers good protection, and fingernails do not leave a mark, neither does rubbing metal on it, though very sharp objects do leave a mark. (see last picture, i tested it with the sharp end of a screwdriver and pushed quite hard. It does scratch but the screen beneath is OK)
One more thing , it does not cover the whole screen, on the top and bottom there is about 3mm of glass to the edge, and on the sides it goes to the curved part. I use the case mate tough case so it does not bother me.
And thats it, pics below, any questions ask me and i will try to answer.
PICS:
Last edited:
