Searching for a full adhesive TGSP I stumbled upon this one on eBay and since it's relatively cheap I got a few to try.
It took a week to arrive and lo and behold - it's really a curved tempered glass screen protector with full adhesive layer and a black border on the sides.
It's a no name brand ( product number FHT013GPT ) but the quality is really good - the oleophobic coating is nice and there are no smudges left and the fingers glide easily.
Installation was a real pain though... Because of the curved edges you need to very carefully center it otherwise you'll get a thin and long air bubble alongside one of the sides.
There are no guide stickers in the kit so using some tape for alignment will certainly be advisable. I never had that many air bubbles getting trapped when installing a protector in the past and just pushing them out with a spudger did not do it this time. I had to press the protector in the middle with one hand while lifting the corners with a finger until it unglues past the air bubble and squeegee the air out while releasing the corner.
The end result is flawless which surprised me given all the lifting I had to do to remove the trapped air and, most of all, the fingerprint scanner works!!!
So far I have been using an Imak combo case and edge glued TGSP. The screen sensitivity, especially around the curved part, was horrible and the fingerprint scanner was not working.
Protection wise there was virtually no gap between the TGSP and the case. With this one the width is identical but there is a tiny gap of around 2mm only on the bottom.
It's almost unnoticeable but after using it for a week I see that it's enough to start accumulating some dust.
There's no cutout for the camera nor the glue is missing in that spot but there's no halo effect.
The image on the screen is probably clipped 1mm on each side by the black border.
That's better than the previously used Imak and certainly some branded ones I've used in the past.
I'm pleasantly surprised by the quality of the product and the fact that the fingerprint scanner works.
This is by far my preferred option for screen protector at this time as I'm not a fan of the messy LOCA glue based ones.
Pour Google Pixel 6 Pro verre trempé 9D colle couverture complète neuve | eBay
Les meilleures offres pour Pour Google Pixel 6 Pro verre trempé 9D colle couverture complète neuve sont sur eBay ✓ Comparez les prix et les spécificités des produits neufs et d'occasion ✓ Pleins d'articles en livraison gratuite!
www.befr.ebay.be
It took a week to arrive and lo and behold - it's really a curved tempered glass screen protector with full adhesive layer and a black border on the sides.
It's a no name brand ( product number FHT013GPT ) but the quality is really good - the oleophobic coating is nice and there are no smudges left and the fingers glide easily.
Installation was a real pain though... Because of the curved edges you need to very carefully center it otherwise you'll get a thin and long air bubble alongside one of the sides.
There are no guide stickers in the kit so using some tape for alignment will certainly be advisable. I never had that many air bubbles getting trapped when installing a protector in the past and just pushing them out with a spudger did not do it this time. I had to press the protector in the middle with one hand while lifting the corners with a finger until it unglues past the air bubble and squeegee the air out while releasing the corner.
The end result is flawless which surprised me given all the lifting I had to do to remove the trapped air and, most of all, the fingerprint scanner works!!!
So far I have been using an Imak combo case and edge glued TGSP. The screen sensitivity, especially around the curved part, was horrible and the fingerprint scanner was not working.
Protection wise there was virtually no gap between the TGSP and the case. With this one the width is identical but there is a tiny gap of around 2mm only on the bottom.
It's almost unnoticeable but after using it for a week I see that it's enough to start accumulating some dust.
There's no cutout for the camera nor the glue is missing in that spot but there's no halo effect.
The image on the screen is probably clipped 1mm on each side by the black border.
That's better than the previously used Imak and certainly some branded ones I've used in the past.
I'm pleasantly surprised by the quality of the product and the fact that the fingerprint scanner works.
This is by far my preferred option for screen protector at this time as I'm not a fan of the messy LOCA glue based ones.
Attachments
Last edited:
). I will also report back on how it goes when it arrives.
. Am finally able to use it (been using a non-LOCA TGSP so haven't been able to use it till now). I enrolled both thumbs and so far each time the sensor has worked and fairly quickly. Only enrolled each thumb once. (Btw, checked to see if any of my other non-enrolled fingerprints could unlock it as has been reported a bit and they could not.)
.
