[Q] Motorola Atrix 4G bricked

[ranjithkumar1201]

Hey Guys,
I tried flashing my rom to CM7 and in the process the phone rebooted and got the error message

SVF:105:1:2
failed to boot 0x1000

No OS detected, going to RSD mode
in 5 seconds
Press a key to stop countdown
Available modes are:
1. RSD
2. Fastboot
3. NVFlash
4. BP HW Bypass RSD
5. BP HW Bypass QC Dload
6. BP Diag & boot AP
7. BP HW bypass BP only
8. BP SW bypass RSD
9. Andriod Recovery
10 .Boot andriod (No BP)
11. Device UID
12. console=ttyS0,115200n8
13. Early USB Enumeration
14..BP tools

I get the error message in the rsd lite as error switching to BP and something.
Kindly help i am really confused.

 

[hoaca388]

Soft brick .

Download moto-fastboot, and unzip to C:\moto-fastboot
DL here:http://www.android-advice.com/file-d...rix_Root_Files

Download system image for 2.3.4 and unzip to moto-fastboot folder
DL here http://www.android-advice.com/file-d...bread_4591_ROM

Download atrix oem unlock and unzip to moto-fastboot folder
DL here:http://gititbit.ch/pub/unlock.zip

open cmd and navigate to C:\moto-fastboot\

Force fastboot on phone by holding down PWR and VOL UP while inserting battery.

Type these commands:

moto-fastboot oem unlock (it will show atrix ID re-enter with ID at end of line)

when finished, then enter these commands:

moto-fastboot flash boot boot.img

moto-fastboot flash system system.img

moto-fastboot -w

moto-fastboot reboot

When it reboots, you will be back to stock, fully restored!!

I then used Pete's Motorola Tools to root my atrix.
Info and DL here http://www.psouza4.com/Bionic/
yes it did work on my atrix make sure usb debugging is on and unknown sources checked.

I then installed CWM to my Atrix
DL here http://forum.xda-developers.com/show....php?t=1475444
unzip to moto-fastboot, put atrix in fastboot mode and open cmd, navigate to moto-fastboot folder and type this:

moto-fastboot flash recovery recovery.img

Reboot and you are DONE!!!! All thats left is to find a ROM and you are good to go

 

[matthew5025]

No need to do all that.
Since you want to get CM7, Unlock the phone.
Ignore the instructions to flash system.img, that will bring you back to stock.
Enter fastboot, flash a recovery. (Above post last instruction)
Enter recovery mode, than flash CM7 from there.

(I assume you are familiar with what I am talking about, and don't require step by step instructions)

 

[ranjithkumar1201]

Bricked

Thank u for ur replies i havent tried it yet but i wish it wud work i was using the latest update from AT&T i think since i tried to boot for the older version this happened i am not sure though.

 

[matthew5025]

There has been posts about trying to unlock after applying AT&T latest update. You should read up on those, I remember it could brick your phone, be careful!

 

[ranjithkumar1201]

Thank You

Dear All,

Thank u a hundred thousand times for helping me get rid of the problem i owe u guys a lot finally got to work.
Thank u once again i dont have words to describe my joy.At ant time u want help in India count me in.

 

[dergezero]

this happened to me to, all i did was go to fastboot and unlock the bootloader and it let me boot again after recovering to a rom i had on my SD. i did try and install a custom recovery when it bricked.

 

[kumarbrijwani]

HI ranjit

Hi ranjith
need your help
can u drop in ur cell number
or call on 9860521352
thanks in advance
kumar brijwani

dear all,

thank u a hundred thousand times for helping me get rid of the problem i owe u guys a lot finally got to work.
Thank u once again i dont have words to describe my joy.at ant time u want help in india count me in.

 

[ranjithkumar1201]

Hi ranjith
need your help
can u drop in ur cell number
or call on 9860521352
thanks in advance
kumar brijwani

9036523279
feel free to sms me
i try to help you in anything i know
it would be better if you could message in Whatsapp

Sent from my MB860 using xda premium

 

[ulkika]

DL here http://forum.xda-developers.com/show....php?t=1475444

error page not found
you can solve this problem....
tank's

Soft brick .

Download moto-fastboot, and unzip to C:\moto-fastboot
DL here:http://www.android-advice.com/file-d...rix_Root_Files

Download system image for 2.3.4 and unzip to moto-fastboot folder
DL here http://www.android-advice.com/file-d...bread_4591_ROM

Download atrix oem unlock and unzip to moto-fastboot folder
DL here:http://gititbit.ch/pub/unlock.zip

open cmd and navigate to C:\moto-fastboot\

Force fastboot on phone by holding down PWR and VOL UP while inserting battery.

Type these commands:

moto-fastboot oem unlock (it will show atrix ID re-enter with ID at end of line)

when finished, then enter these commands:

moto-fastboot flash boot boot.img

moto-fastboot flash system system.img

moto-fastboot -w

moto-fastboot reboot

When it reboots, you will be back to stock, fully restored!!

I then used Pete's Motorola Tools to root my atrix.
Info and DL here http://www.psouza4.com/Bionic/
yes it did work on my atrix make sure usb debugging is on and unknown sources checked.

I then installed CWM to my Atrix
DL here http://forum.xda-developers.com/show....php?t=1475444
unzip to moto-fastboot, put atrix in fastboot mode and open cmd, navigate to moto-fastboot folder and type this:

moto-fastboot flash recovery recovery.img

Reboot and you are DONE!!!! All thats left is to find a ROM and you are good to go