Hard Bricks are not done deals and this why this forum gets slammed everywhere. Try helping senior member. So damn negative around here...unreal.
[Q] Motorola Atrix Hard Brick failed to boot 0x1000
- Thread starter Andr3s
- Start date
Uhhh.........that's why it's called a HARD brick...........because you cannot recover. If you are lucky you will get a replacement or repair through warranty. Sure, Motorola can fix it as far as we know, but the vast majority of folks posting also are out of warranty, or do not have insurance on their hardware.
A SOFT brick is a different matter, and herein is where the problem lies. People post hard brick conditions, then a slew of other people start posting solutions for soft bricks.
Also, the same threads are repeatedly created over and over because people are too lazy to do some research before posting. Nobody wants to be told they have a hard brick, but the reality is that hard bricks are a reality!
<edit> Where is the help you are providing? What is your solution for a hard brick???
Last edited:
i need see the screenshot of the error, i have the solution...:good:
This is what works !!!!!!
well guys , i actually followed two threads........... this an another one and im good now...
device bootloader is unlocked.. and im rooted
all i will say is lok at the pic and follow the commands highlighted by the white dash
well guys , i actually followed two threads........... this an another one and im good now...
device bootloader is unlocked.. and im rooted
all i will say is lok at the pic and follow the commands highlighted by the white dash
Literally your set is Dead. It can't be brought back.
I'm interested to buy a hard brick set. I'd try my best to recover it (If I'm successful others will be benefitted too!)
If interested please PM me (including your IMEI)
I'm interested to buy a hard brick set. I'd try my best to recover it (If I'm successful others will be benefitted too!)
If interested please PM me (including your IMEI)
even though the other members are hammering you, the post still helped me recover from a soft brick....thanks
Boot failed error
i used RSD process and bricked my phone.
it shows SVF:105:1:2
failed to boot 0x1000
and after 1 - 2 seconds screen become blank.
is there any solution for this hard brick. im soo much worried about my phone and cant afford this big loss for me.
or add me at skype ([email protected] and [email protected].
i will very very grateful to you.
Hello sir, i m facing a serious proble with my moto atrix MB860.
i used RSD process and bricked my phone.
it shows SVF:105:1:2
failed to boot 0x1000
and after 1 - 2 seconds screen become blank.
is there any solution for this hard brick. im soo much worried about my phone and cant afford this big loss for me.
or add me at skype ([email protected] and [email protected].
i will very very grateful to you.
It is already step by step... Perhaps you missed the second fastboot oem unlock?
Enviado desde mi MB860 usando Tapatalk 2
Enviado desde mi MB860 usando Tapatalk 2
i realize that, but i meant walk me through it, in detail....sorry about that if it would take up time, but i would really love my phone to be up and running again
You just described the procedure in detail. Follow the steps
Sent from my MB886 using xda app-developers app
Informative but didn't work... :/
Hello sir. my atrix is bricked while using RSD .. it just shows the boot error and then blank display
..
I recently bought it for high cost.. it's not entering in fastboot mode aur rsd protocol mode..
i tried using nvflash recovery with factory repair cable.. but when i use any command .. Like "nvflash --sync" (the simplest) it shows :
plzzzzz I need helppp
Hello sir. my atrix is bricked while using RSD .. it just shows the boot error and then blank display
..I recently bought it for high cost.. it's not entering in fastboot mode aur rsd protocol mode..
i tried using nvflash recovery with factory repair cable.. but when i use any command .. Like "nvflash --sync" (the simplest) it shows :
then pc disconnects it .. I have JTag it.. but still not going in fastboot aur any other flash mode. :/ :/ :/
plzzzzz I need helppp
Too much bickering going on here... I'm leaving this thread open so that you guys can hopefully fix your bricked devices but it will only remain open so long as the childish bickering stops. We do not need it here !! As this thread is old, a lot of links are down. Consider this a warning regarding the previous behavior within this thread .
Thread cleaned
Thread cleaned
Thanks for the more official and tactful way of trying to get things back on track. Comparing my last post to yours, yours is a bit more effective
Sent from my MB886 using XDA Free mobile app
fail to boot 0x1000
The phone shows fail to boot 0x1000 then shuts off
Things that dont work Holding the vol up and power while inserting the battery .. phone still shuts off
Rsd not detecting the phone because it turns off after the error comes up.
Recovery mode dont work , phones displays error then turns off.
What was notice though if you leave the battery in it drains it regardless of the fact that it turns off. However it would seem as if something is running with the lcd off because the battery does drain and also the only way to turn if back on is a battery pull. When you power on again you get the same error , hence you have to battery pull again.
By the way this is different from the other fail to boot 0x1000 that list the menu for you to choose from , that one is easily fixed by flashing over the rom. This one is not being detected by the PC which is why there seem to be no fix for it so far.
The phone shows fail to boot 0x1000 then shuts off
Things that dont work Holding the vol up and power while inserting the battery .. phone still shuts off
Rsd not detecting the phone because it turns off after the error comes up.
Recovery mode dont work , phones displays error then turns off.
What was notice though if you leave the battery in it drains it regardless of the fact that it turns off. However it would seem as if something is running with the lcd off because the battery does drain and also the only way to turn if back on is a battery pull. When you power on again you get the same error , hence you have to battery pull again.
By the way this is different from the other fail to boot 0x1000 that list the menu for you to choose from , that one is easily fixed by flashing over the rom. This one is not being detected by the PC which is why there seem to be no fix for it so far.
Great work and utmost help
Atlast I found a great help that I could unbrick my phone mb861. I could not find even build # on about phone. I tried too many methods. Thanksd a million
Atlast I found a great help that I could unbrick my phone mb861. I could not find even build # on about phone. I tried too many methods. Thanksd a million
Our Apps
Get our official app!
The best way to access XDA on your phone
Nav Gestures
Add swipe gestures to any Android
One Handed Mode
Eases uses one hand with your phone