[Q] NOOK HD+ with cm-10.1-emmc hangs on CyanogenMod log.

[sean_nj]

Hi guys,

I just got two HD+ 32GB and installed cm-10.1-20130527-UNOFFICIAL-ovation-emmc following evergreen and leapinlar's instructions. The installation went well, and I can boot the tablets into twrp recovery. But I cannot boot one tablet into Android. It always hangs on CyanogenMod log (the rotating circle/wheel with CyanogenMod text at the center) when trying to boot into Android. I reboot the tablet several times now and still have the same issue.

I repeated the same procedure on another Nook HD+ 32GB and I can boot the second tablet into Android after several reboots. But I still have no luck with the first tablet.

Any suggestion?

Thanks a lot for the help!

Sean

 

[Ravynmagi]

I installed CM10.1 eMMC on my HD+ for the first time last night and the same thing happened to me. So I went back into recovery and installed the CM10.1 again and then it booted up normally afterwards. So in my case at least it seems like it didn't install right on the first try.

 

[sean_nj]

I installed CM10.1 eMMC on my HD+ for the first time last night and the same thing happened to me. So I went back into recovery and installed the CM10.1 again and then it booted up normally afterwards. So in my case at least it seems like it didn't install right on the first try.

Thanks a lot for the suggestion. I finally got It to work by booting into TWRP to wipe system, data, and caches, then re-installing from zips.

Sean

 

[jdburns]

Same issue, apparently (hopefully...) resolved

LIke many other posters here and elsewhere, I installed CM 10.1 on my brand new Nook HD+ 32gb, got it to boot into CWM after many trials and tribulations (I had to reboot about 30 times to get the device to boot into recovery from SD; it crashed halfway through backup in spectacularly frustrating fashion, and it took me about 30 more hard resets to get it to boot into CWM again. I used a brand new Amazon Basics 32gb class 10 card). I did a little victory dance, loaded up some apps (probably too aggressively: 50 or 60 of them), rebooted, and.... you know what happened then, or you wouldn't be reading this (probably whilst sweating and/or crying).

After uninstalling some resource-intensive apps, then booting into recovery and wiping both caches, I was able to reboot normally (aside from waiting a couple of minutes for apps to be "updated" or "optimized" or whatever), but the next and all subsequent reboots failed unless I first booted into recovery and wiped the caches.

Finally, after reading a number of posters with the same problem (including @Ravynmagi and @sean_nj here--thanks, guys), I took a deep breath, did a full Titanium backup, booted into CWM, did a factory data reset, and reinstalled the three zips from the bootable SD. CM booted quickly and normally. I rebooted a couple of times with no problems. I installed a few apps, rebooted normally. I installed a few more apps (including a couple which I sideloaded), again rebooted normally. In the last 18 hours, I've installed a few more apps, played some resource-intensive games, tested Netflix and a sideloaded video, etc.

As of now, the device works like a charm and boots quickly and without drama. If anything changes (and I'm still able to communicate like a civilized human being), I'll make sure to update here.

 

[acr123]

unable to reboot get spinning logo

I recently updated Nook HD+ to 10.1 w/o problems.Each time I have rebooted it take 2 -3 tries before it finally boots ups. Those other times if boots to the spinning Cyanogen logo. Is there something I can do to check with the system booted up correctly to figure out the problem. If not, what steps should I take now and how do you do a complete backup of all the newly added material since the initial update. Thanks again,

Al

 

[ohrenstaebchen]

I'm facing the same problems but with a different setup: latest CM 10.2 Carbon ROM release (both versions with and without multiwindow). I have random bootloops and I'm unable to track down the problem.

Are we the only users with those bootloops?

 

[silkshadow]

Was searching for this. I am not having a problem booting per se, but all of a sudden I am getting a weird booting thing. Where the logo comes up and spins but its distorted, then it becomes normal looking, then my Nook will kind of reboot. Not a complete reboot just the screen goes black for a millisecond and then the logo starts over again where its all distorted, then it goes normal and then it boots.

I guess you can call it a logo boot loop. The thing is, it doesn't happen all he time, just most of the time now. When it happens, my SD card is incorrectly mounted and I have to umount it and take it out physically and re-insert it.

Nook HD+ 32gb, CM 10.1.3 stable and mbg4ga emmc. Not sure if this is the same as you guys but it sounds related. I've re-flashed several times. I think if you guys can find a cure, then it would probably work for me as well. Quick question, any of you guys using auto-patcher to patch Pdroid? How about Xposed?

 

[josim]

For getting caught in the boot loop try:
Settings>Launcher>uncheck wallpaper quick render.

This is for stock Trebuchet 1.0 Launcher. I hope the developers are aware of this.

Probably coincidental but, the glitch caused by the magnetic closure on my case much better.(when you try to unlock and it blinks and goes back to lock).

Good luck.