[REPARTITION] Nexus 4 Repartition [MAKO] [8GB/16GB] [UA TWRP]

[MacacoVei]

Worked! Just installed Carbon-CR 7.0 + gapps 9 + magisk.

I confessed I didin't read correctly. My fault. I'm used to just flash and install and had to read and search.

These are important:

4. Do the actions asked by repartition pack (go to Terminal in ordinary recovery and input word that pack will tell you. Everything else will be done automatically).

-> I think for me it was "open" (i dont remember well. just one word)

6. Install TWRP from below (it is build with support of new partitions layout and sizes. It can be differed from official TWRP by next format 3.x.x-1 UA).

-> I forgot how to install img. Go to fastboot (volume up/down pressed while turn on) -> fastboot devices (check if your phone is synced) -> fastboot flash recover <your img file.img>




Thanks a lot OP

 

[mauriciognr]

Will you update the UA recovery to lastes TWRP?

 

[saeedgh08]

Do the actions asked by repartition pack (go to Terminal in ordinary recovery and input word that pack will tell you. Everything else will be done automatically).
Sorry bur What does this mean?
What should I do?

 

[TundraLK520]

Do the actions asked by repartition pack (go to Terminal in ordinary recovery and input word that pack will tell you. Everything else will be done automatically).
Sorry bur What does this mean?
What should I do?

Flash the repartition zip (make sure to tick system in mount options). It gives directions to type something (modify in my case) in twrp terminal. Terminal can be found under advanced tab in twrp.
I wrote my experience about flashing this zip in this thread some time back , if u have some patience, u can check that too.

 

[saeedgh08]

error failed to mount /vendor ( invalid argument)
What should i do ? Help
(Device is root & bootloader is unlock)

 

[pxrave]

no update planend?

 

[saeedgh08]

Ha ha now system & data mount error

 

[TundraLK520]

Ha ha now system & data mount error

Just copy n pasting my previous post:

I'm getting unable to mount vendor errors. I went into mount section from twrp but can't select the vendor option, it allows me to select every other option just not vendor. Also part about missing updater script.
Update:
I downloaded the official twrp and tried again this time no vendor errors but it says missing updater script.

Final Update:
I can just say to read instructions carefully. I did the mistake of trying to repartition on UA twrp instead of official twrp which was giving me vendor errors. As for the updater script error, I re downloaded the repartition zip and it flashed successfully (make sure to tick system in mount options). Then it gave me directions to type modify in twrp terminal. Upon which it started the repartition and rebooted to recovery and the I flashed UA twrp and followed the procedure mentioned, don't worry about the mounting errors when wiping and then advanced wipe everything. Then flash ROM and after that resize through wipe section ticking the system option. Which results in error the first time and then do it again. This time no error. Now you can successfully flash gapps.

 

[saeedgh08]

Just copy n pasting my previous post:

I'm getting unable to mount vendor errors. I went into mount section from twrp but can't select the vendor option, it allows me to select every other option just not vendor. Also part about missing updater script.
Update:
I downloaded the official twrp and tried again this time no vendor errors but it says missing updater script.

Final Update:
I can just say to read instructions carefully. I did the mistake of trying to repartition on UA twrp instead of official twrp which was giving me vendor errors. As for the updater script error, I re downloaded the repartition zip and it flashed successfully (make sure to tick system in mount options). Then it gave me directions to type modify in twrp terminal. Upon which it started the repartition and rebooted to recovery and the I flashed UA twrp and followed the procedure mentioned, don't worry about the mounting errors when wiping and then advanced wipe everything. Then flash ROM and after that resize through wipe section ticking the system option. Which results in error the first time and then do it again. This time no error. Now you can successfully flash gapps.

Hi I read your pre post but my problem is: system and data not mount and " invalid argument error error16" and system & data do not repair or resize and change type
i Tried to unbrick method on first page it is not work for me
Pls guide me to i can repair my device @Clamor

 

[Clamor]

@saeedgh08 format system and data in advanced wipe

 

[saeedgh08]

@saeedgh08 format system and data in advanced wipe

Hi i can't i type "yes" but this error is shown (pic attached)

 

[saeedgh08]

@Clamor and this pic

 

[Clamor]

@saeedgh08 take a partition log

 

[saeedgh08]

@Clamor thx for your method
I read the instructions carefully and stepped in and the phone came in. But now, the memory capacity of 8 GB and Bluetooth do not have a MAC address. How to fix the problems?

 

[Clamor]

@saeedgh08 primary take a partition log, then we will fix else

 

[Clamor]

3.3.1-1 UA TWRP is already available in download section.

 

[down33]

in fact easiest way TO Repartition android system

Thank you ..

 

[p3terr]

@Clamor Noob question here, I don't know where to find this part of the instructions in TWRP

1. Boot into recovery (You need to allow system partition modification to be able resize /system in recovery).


I'm also currently running TWRP 3.2.1.0, will that work to do the first steps before flashing the new TWRP mention in OP?

help.

 

[Clamor]

@p3terr if you are making repartition for the first time than you can use TWRP from TeamWin any version 3+. If you are updating from UA TWRP you need just to flash it.

 

[MACAR¥O D£ T€XA$]

Need little help please

Hello, I have a doubt I read a comment about the repartition, which says that if it is the first time I can use the official team win twrp I have the latest version installed, my doubt is and to be sure I do the steps for repartition with the team win and then install the one provided in the post or can I continue with the team win nothing else? the question is about the risk of losing mac address of wifi / imei or bluetooth, it is the first time I do repartition in my mako
PD: 3.3.1-0 is my twrp version