You're going to have to look into it on your own, I'm afraid :\
You're going to have to look into it on your own, I'm afraid :\
You're kinda doing everything wrong, based on what you've mentioned. Since you've probably f***ed it all up at this point, restore with Qualcomm EDL (restores back to stock, remember to keep your unlock_token binary if you ever wish to unlock again!!!). Don't flash from TWRP, TWRP isn't ready for these devices. If you bothered to follow directions you'd know that you can only use Pixel Recovery to format and sideload, remember to do both a and b name-schemes. As for GApps, I used MagiskGApps converted just for testing (careful with this method, never disable the module, or you'll bootloop).Man, how do I erase this ROM??? I've tried installing the GAPPS version over the Vanilla, and no go, it says unable to downgrade. Then I tried to format and install TWRP to do a wipe, and the touch controls dont work. I've tried sideloading GAPps and it says no room in partition, try a smaller file. Im using the smallest one!
You should always format before a sideload. EDL flash restore (entire phone, remember, you lose unlock status, you will need to reflash unlock token, but fortunately no need to get a new bin file). Flash pixel recovery to both recovery_a and recovery_b, boot into recovery_a, stay in recovery and: format, sideload, run adb in the recovery menu and then use set-active for b, reboot directly into recovery (it should take you to b), format, sideload, then reboot. The whole 'a/b' active slot for boot is a lot like dual-boot for Windows/Linux. They're unique on their own. For example, you could have Android 10 and Android 11 on the same phone, if you wanted. A simple set-active would select which set of partitions to use. By the way...FLASH YOUR BOOT PARTITION(s) with the boots that come with the ROM. Otherwise you'll most likely get looped to recovery. I had to do that for my billie8t. You can pre-magisk the boot(s) img files before flashing if you want.Thanks and sorry I miss spoke. I tried to install the Gapps version of arrow on top of the vanilla... It didn't work and that's when I got the cannot downgrade. I tried to install the pixel recovery through the arrow recovery and that didn't work either. I'll try your other suggestions, and yes still have the token. Where would I find the magiskGapps, or will that not work now either?
Why are you attempting to Sideload Magisk? Who said to do that? Install the Magisk APK, copy your BOOT img over, patch it, then flash the resulting BOOT image over boot_a and boot_b...Alright, I have a lot figured out now, formatted partitions and installed pixel recovery in both. Got the fresh rom installed and so far so good! The only issue now is that I've lost super user access, and I can't sideload Magisk to use that for some reason?? Is there another super user apk that works with this recovery, etc? Thanks again for your help!
You don't need root to patch a BOOT img. Install the APK, run Magisk and simply patch your BOOT img, then use fastboot and flash the boot_a and boot_b partitions with that patched BOOT.img. Ignore anything to do with TWRP, that should have been very obvious at this point.Well I was on the Magisk download site, and while I can install the apk, I still don't have root access. On their site it says to load the magisk.zip using twrp, and since twrp doesn't work on this phone/recovery I tried sideload... I'll try the patching route
...You're kidding right? Who said patch the recovery image? It always has root.. Several posts saying BOOT... FFS. Letting anyone else deal with this person. Five times I said BOOT...Lol, yes I got the don't use twrp innuendo... I did patch the pixiel recovery image in Magisk, and flashed in partitions a and b, but no luck with getting root. I even started over by doing a format on both partitions and reloading the patched boot image and ROM, still no go. I'll keep messing with it.
Not being a ****, you aren't reading. Piss on someone else with your reverse-blame.No need to be a ****, not everyone is as experienced as you... Other threads said the recovery so I tried that. I'll move on to the boot, which I hadn't downloaded, and thank you for your snarky assistance.
The baseband/modem is rarely ever connected to wlan firmware at all (separate chipsets, usually, separate firmware files as well). That being said, maybe they used a different chipset for yours and something isn't by default connecting at a higher standard. Confirmed you're operating at the same 802.11 standard as router? Double-check your case...seen a lot of garbage cases wreck signal. I'd bet it is a conf issue, not firmware. Identify your wlan chipset and see if it is the same as the assumed chipset(s) of Arrow. This is also a ROM for the 5G models, there were baseband differences, though I don't know if it was chipset or firmware. I have noticed some Android devices having wireless issues (cell or wlan) if they replaced/changed versions of firmwares or ROMs, sometimes crappy router firmwares assume profiles of devices and any changes goof something up, notably on NetGear firmwares. Tried restarting router, just to be sure?Hi guru's,
I have just installed the vanilla arrows OS rom on my N10 (BE2029) because stock room was a nightmare (interface issues, impossible to answer calls, minutes of freezing and all that stuff).
Just flashed it yesterday, so far so good, except for one point, quite huge one.
The WiFi range is really poor, I mean I have to be in the same room as my box or I lose the signal.
When I'm connected the speed is as good as with the stock rom.
That's why I think the modem is the culprit here.
Did you ever face this misbehaviour ? Any solution without flashing modem ? And if not, how can I know the modem to pick ?
Thanks for reading !
Heykel.
Hi Odin,The baseband/modem is rarely ever connected to wlan firmware at all (separate chipsets, usually, separate firmware files as well). That being said, maybe they used a different chipset for yours and something isn't by default connecting at a higher standard. Confirmed you're operating at the same 802.11 standard as router? Double-check your case...seen a lot of garbage cases wreck signal. I'd bet it is a conf issue, not firmware. Identify your wlan chipset and see if it is the same as the assumed chipset(s) of Arrow. This is also a ROM for the 5G models, there were baseband differences, though I don't know if it was chipset or firmware. I have noticed some Android devices having wireless issues (cell or wlan) if they replaced/changed versions of firmwares or ROMs, sometimes crappy router firmwares assume profiles of devices and any changes goof something up, notably on NetGear firmwares. Tried restarting router, just to be sure?
We don't have to play modem-flashing games anymore. As for why you might be having issues, it could be due to an APK missing. For instance, I'm on Mint Mobile, an VMNO, which uses T-Mobile's network. If I don't have T-Mobile APKs installed that customize the Wi-Fi Calling and VoLTE activation...then I can't use those features and *must* disable them to use regular “5G” (5G protocol over low-frequency 600MHz, aka fake 5G just like AT&T and such)/LTE. Video call would also bust. All would either not work at all or they would start but then stop. That's due to T-Mobile's custom backend bull**** because they wrote it themselves instead of licensing properly-confirming backends.Hi Odin,
Thank you for the answer, and sorry for the late reply, was pretty busy those days.
Well, regarding my SIP box, it's a pretty good one, so nothing wrong with my router, I'm affraid.
Plus, all my devices are working pretty well, girlfriend Xiaomi, Firestick, etc...
It really happened consecutively to my ROM flash.
I will dig here and there to see if I can update my modem only on this Oneplus crap (when I was on CM years ago, on Samsung devices, I remember I've tested many modem to get the one, but I don't know if nowadays it is still possible to do it, especially with Arrow...)
Heykel.
/*
* We are not responsible for bricked devices, dead SD cards,
* thermonuclear war, or you getting fired because the alarm app failed. Please
* do some research if you have any concerns about features included in this ROM
* before flashing it! YOU are choosing to make these modifications, and if
* you point the finger at us for messing up your device, We will laugh at you.
* It is your fault because you chose to do all the modifications on your device.
* Remember projects like these and the work done on them is a hobby to the
* contributors and the team members, no one is working for you nor is getting paid for it
* have some respect for the work done by them since it is done purely on interest or a hobby
*/
INSTRUCTIONS (leave a like so that more people see this):
Why are you attempting to Sideload Magisk? Who said to do that? Install the Magisk APK, copy your BOOT img over, patch it, then flash the resulting BOOT image over boot_a and boot_b...Alright, I have a lot figured out now, formatted partitions and installed pixel recovery in both. Got the fresh rom installed and so far so good! The only issue now is that I've lost super user access, and I can't sideload Magisk to use that for some reason?? Is there another super user apk that works with this recovery, etc? Thanks again for your help!