I don't know the BEST one, but MGC_8.2.204_Parrot043_V5 works well for me.Tôi có thể hỏi bạn. phiên bản Gcam nào hoạt động ổn định trên ROM 7.7 này. cảm ơn
+1Thank you for v7.8.
I updated by OTA, and reinstall NikGapps-core-arm64-11-20210704-signed.zip because of boot loop occured.
It works fine other than zenparts->vibration strength.
Remove magisk hide props module and flash this from recovery+1
Also SafetyNet attestation fails despite Magisk Hide props config. Any solution?
You may use mindthegapps instead (find the link from OP). It's a bit outdated but cause no bootloops on upgrade.Thank you for v7.9.
I updated by OTA, and reinstall NikGapps-core-arm64-11-20210804-signed.zip and NikGapps-Addon-11-Gmail-20210804-signed.zip because of boot loop occured.
It works fine other than zenparts->vibration strength.
You may use mindthegapps instead (find the link from OP). It's a bit outdated but cause no bootloops on upgrade.
Vibration strength is working fine here even under enforcing state. Send me logs.
Max charging current is set to 2mA, same as stock rom. Havnt enabled fast charging for safety concerns. You may change to a kernel which supports fc if you want.I'm facing low charging speed in v7.8. ( clean installed ). Is there a kernel limitations in this rom for charging speed ???
It's working here. I'd suggest you a clean installThank you for reply.
I'll install mindthegapps next time.
Thank you very much.
I sent logcat via conversation.
And changing Zenparts->SELinux mode from permissive to enforced makes 'ZenParts keeps stopping'.
I clean installed crDroidAndroid-11.0-20210811-X01BD-v7.9.zip and MindTheGapps-11.0.0-arm64-20210412_124247.zip, and restored apps from google drive and the same issue happened.
I reinstalled cleanly as follows.I clean installed crDroidAndroid-11.0-20210811-X01BD-v7.9.zip and MindTheGapps-11.0.0-arm64-20210412_124247.zip, and restored apps from google drive and the same issue happened.
The stock firmware of UL-ASUS_X01BD-WW-17.2018.2004.424-user.zip was used before the first crDroid (crDroidAndroid-10.0-20200610-X01BD-v6.7.zip) was installed.
Was this an infuluence ? Or is it bad to restore apps from google drive ?
Yes, I can confirm the issue of vibration setting too.I reinstalled cleanly as follows.
(1) factory reset
(2) format data
(3) advanced wipe (Dalvik/ART cache, cache, data, internal storage, system and micro SD card)
(4) install crDroidAndroid-11.0-20210811-X01BD-v7.9.zip from USB-OTG.
crDroidAndroid-11.0-20210811-X01BD-v7.9.zip was checked by sha1.
(5) reboot to recovery
(6) install MindTheGapps-11.0.0-arm64-20210412_124247.zip from USB-OTG.
MindTheGapps-11.0.0-arm64-20210412_124247.zip was checked by md5.
(7) reboot to system
(8) WiFi setting
(9) skip data copy
(10) skip google restore.
(11) skip finger print setting
(12) skip restoring apps and data
But the same issue happened.
Thank you for reply and confirm.Yes, I can confirm the issue of vibration setting too.
I can't save vibration strength value in ZenParts.
And 'Touch vibration' doesn't work for me yet.
On the other hand, the issue of 'Hide nav bar' setting was solved with v7.9.
Anyway, these are not critical for me.
*** Disclaimer
I am not responsible for any damage you made to your device
You have been warned
Bootloop is caused by the latest nikgapps. Downgrade nikgapps untill the developer fixes the issue or it'll happen againThank you for v7.3 (20210209).
After updating to v7.3 with OTA, a boot loop occurred.
Therefore, I dirty flashed NikGapps-core-arm64-11-20210130-signed.zip with TWRP and it started normally.
Bluetooth headphones work well.
ZenParts -> Vibration couldn't be saved.