[ROM][13][OFFICIAL] PixelExperience (Plus) [DISCONTINUED]

[KillerTheLord]

I tried to access the settings via dialer (and a 3rd party app, Network), *#*#3282#*#* but it is missing code and won't open. I'm unable to change any radio settings related to the LTE modem.

I actually tried the fix on LOS thread.

1. Fixing the carrier settings file has no impact. I tweaked a few other values too, no change.
2. I then tried installing LOS and lost all connectivity (like a bunch of people reported with verizon).
3. Tried the steps outlined in https://xdaforums.com/t/official-lineageos-20-for-the-razer-phone-2.4514853/post-88018563
4. Eventually no amount of factory reset and flashing ever brought back connectivity. Only stock ROM would have connectivity.

I am now on MR6 (rooted) to ensure things work.

 

[A30N]

Nevermind, I got into the hidden network settings by dialling *#*#4636#*#* and was able to change LTE settings such as Volte and preferred network type, run ping tests, etc.

 

[phAnt0mg33k]

OK wired one and i am tiring to capture a log cat to submit it but Bluetooth during a phone call will just randomly disconnect. normal media playback I have no issues at all with disconnecting. Also the speaker phone mic is super quiet. If i get a log cat of the issue I will post it. the headset has no effect either.

Jsut a side note this rom was reset to factory with this last update as I was still on 12L A fresh install as done no root was ever done.

 

[Alcatraz323]

Feb updated, check #2 for changelog

 

[Prungle]

The update to 13 has been terrible for me. My battery runs out from full charge in 4 hours. RTT is still an issue with incoming calls from iPhones, the caller is muted, I have to call them back to be able to talk. Editing the carrierconfig RTT values did nothing. Performance seems sluggish.

I've tried factory wiping, reverting to stock, wiping again and installing pixelexperience to no better result.

I ran pixelexperience 12 for about a year and it worked wonderfully (aside from iPhone RTT issue)

 

[Alcatraz323]

QPR2 with march security released, check #2 for changelog

 

[Alcatraz323]

3.30 updated, added sdcard/otg support in recovery so that a dead typeC won't really isolate this phone from flashing
Swiched full architecture to armv8-2a and kryo385, optimized in every aspect
and some minor fix for QPR2
For detail pls check #2

 

[Vordeqor]

Hi, just installed Pixel Experience Plus and I seem to have a problem reading the SIM card. Tried sim cards from different networks and none of them work. Not really sure what to do at this point, looking for some guidance. Thank you!

 

[Alcatraz323]

Hi, just installed Pixel Experience Plus and I seem to have a problem reading the SIM card. Tried sim cards from different networks and none of them work. Not really sure what to do at this point, looking for some guidance. Thank you!

Rp2 is not hot swappable, you need a reboot when you insert a sim

 

[Vordeqor]

Rp2 is not hot swappable, you need a reboot when you insert a sim

Thank you for your prompt response, and yes that did in fact correct my issue, which has now raised another one! I am able to connect to the AT&T network and that works, but when I swap in a sim card from Entel (I'm currently in Chile), it recognizes the sim from entel but says (Temporarily Unavailable). Tried googling a solution to no avail.

 

[Alcatraz323]

Thank you for your prompt response, and yes that did in fact correct my issue, which has now raised another one! I am able to connect to the AT&T network and that works, but when I swap in a sim card from Entel (I'm currently in Chile), it recognizes the sim from entel but says (Temporarily Unavailable). Tried googling a solution to no avail.

A swapping also need a reboot

 

[Vordeqor]

A swapping also need a reboot

I did reboot this time but I'm still getting the same issue

 

[Alcatraz323]

I did reboot this time but I'm still getting the same issue

Then I don't know, most of carrier working good

 

[Vordeqor]

Then I don't know, most of carrier working good

Yeah it seems to be this carrier Entel. I tried my wife's sim card and got the same issue. Thanks for your help and time

 

[kocco]

Hi, I seem to be unable to add fingerprint. Using family link device management for kid, after confirming that I agree I should proceed to fingerprint setup but getbonly black screen and nothing happens. Any idea or workaround?
Also ambient display doesn't work and crashes every time I try to set it up.
Thanks for any suggestions.

 

[Alcatraz323]

Hi, I seem to be unable to add fingerprint. Using family link device management for kid, after confirming that I agree I should proceed to fingerprint setup but getbonly black screen and nothing happens. Any idea or workaround?
Also ambient display doesn't work and crashes every time I try to set it up.
Thanks for any suggestions.

Fingerprint/Ambient display always working
1. Please be sure you are using my rom not pe gsi
2. If you have installed Magisk/modules, remove it
3. If you used other kernel you should re flash the rom, no other kernel is recommended
4. If things above don't solve, then issue might from your device I don't know how to get it fixed

 

[Lewislow94]

Hi, I'm need help just trying to install Pixel Experience plus and stuck at flashing recovery can't get through. Error code below

warning: skip copying boot image avb footer (boot partition size: 0, boot image size: 67108864). sending 'boot' (65536 kb) failed (write to device failed (invalid argument)) fastboot: error: command failed

 

[Alcatraz323]

4.19 updated. Fixed usb, add battery manage system, and more, pls check #2 for details.

 

[Alcatraz323]

Hi, I'm need help just trying to install Pixel Experience plus and stuck at flashing recovery can't get through. Error code below

warning: skip copying boot image avb footer (boot partition size: 0, boot image size: 67108864). sending 'boot' (65536 kb) failed (write to device failed (invalid argument)) fastboot: error: command failed

change cable, you need pc usb 3.0 cable usb 3.0, not a pc usb 3.0 cable 2.0 or something else

 

[Lewislow94]

change cable, you need pc usb 3.0 cable usb 3.0, not a pc usb 3.0 cable 2.0 or something else

Successfully installed, thank you.