[ROM][Guide][FULL ODIN FILES][ATT][OC1][OTA with KEEP ROOT][Soft Brick FIX]

[carl1961]

@carl1961 my N3 doesn't turn on at all.... Looks like a hardware problem :'( Don't know what to do right now. When I press power button nothing happens

Did it happen with safestrap? A USB jig got mine to bootloader. If it's the power button broke, I read somewhere this week how to get it to turn on. I had to fix mine with a old part , ( I wore the button themble, out, that tiny metal circle that's taped and glued to power ribbon).

 

[Walter.White]

Did it happen with safestrap? A USB jig got mine to bootloader.

I think its the battery. Not sure though. Wish I had a spare one to test

Anyway I have a N4 build for you to test. I just need to upload it

 

[andygev35]

When I connect to wall charger nothing happens. But I just connected it to my laptop and it reboot? I'm scratching my head here. I was talking to my friend and it just shutdown on me.

Also my battery isn't charging at all? Do you think a dead battery could do this?

Sounds to me like either a bad battery, or more likely a poor battery connection. I'd pull the battery and inspect the pins and the battery pin locators.

Sent from my AT&T Galaxy Note 3 using Tapatalk®

 

[carl1961]

FAILED! WTF =(

<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_N900AUCUCNC2_722276_REV03_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BL_N900AUCUCNC2_722276_REV03_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_N900AUCUCNC2_722276_REV03_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CP_N900AUCUCNC2_722276_REV03_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_ATT_N900AATTCNC2_722276_REV03_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sdi.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

Looks like it failed at the start of the system.img.ext4, file size reads correct, comparing it to op. Wish I could help, I know nothing about a mac pc.

 

[Walter.White]

Sounds to me like either a bad battery, or more likely a poor battery connection. I'd pull the battery and inspect the pins and the battery pin locators.

Sent from my AT&T Galaxy Note 3 using Tapatalk®

After doing some more testing battery is fine. It is either the USB Adapter that came with N3 is bad or the wall outlet is bad.

 

[carl1961]

After doing some more testing battery is fine. It is either the USB Adapter that came with N3 is bad or the wall outlet is bad.

I hope it's that easy to fix. Mine was a bad button , I ordered a new one (6.00 free shipping, put it in and it did not work, had to put my old one back. I ordered another one today from a more replical place, .

 

[jdmsohc22]

thank god for Parralels on MAC, I'm back up and running..!!

Thanks!!

PS EDIT - It seems I only have data on Wifi..? I'm getting texts, emails, etc but once I take it off Wifi my signal goes away? I got a message about my sim card and asked me to reboot and I did, but still no go..?? Do I have to adjust any network settings??

 

[jdmsohc22]

Not sure what happened, but a few reboots, and it seems to be working again.. lol oh well, hopefully it stays working!

 

[blane3298]

I just picked up a note 3 for cheap. Can I Odin from nj5 back to nc2 so I can root or am I stuck on 4.4.4?

 

[carl1961]

I just picked up a note 3 for cheap. Can I Odin from nj5 back to nc2 so I can root or am I stuck on 4.4.4?

Yes you can.

 

[imanony]

If you do not want root, then install with odin the NC2 stock firmware
Below,
N900AUCUCNC2_Full_Odin_Tar.rar

What is the difference between this N900AUCUCNC2_Full_Odin_Tar.rar file and the Home.tar file that is in the first post of this thread?

 

[carl1961]

What is the difference between this N900AUCUCNC2_Full_Odin_Tar.rar file and the Home.tar file that is in the first post of this thread?

The full tar is the 4 files combined it will factory reset and wipe your internal sdcard.

 

[resac]

hi carl,
even after i flash with the full odin NC2 flash in my NOTE 3 its not showing CP, in *#1234#.

but if i flash the MLG modem file then it will show CP: MLG


whats the issue?????

 

[carl1961]

hi carl,
even after i flash with the full odin NC2 flash in my NOTE 3 its not showing CP, in *#1234#.

but if i flash the MLG modem file then it will show CP: MLG


whats the issue?????

do the 4 separate files then use and select the pit file.

Mine shows up but of course I am on NJ5

 

[resac]

Doing with the 4 diff files only which you posted it on Forum.. i need to check the re partition???

 

[carl1961]

Doing with the 4 diff files only which you posted it on Forum.. i need to check the re partition???

It will automatically select when you attach pit file, you select the 4 files and the pit file. That will make your phone factory restored.

 

[resac]

It will automatically select when you attach pit file, you select the 4 files and the pit file. That will make your phone factory restored.

But my question is , i am doing same as of u said. but whenever i flash the NCUC2 firmware my imei become null and Baseband also shows unknown. just i am wondering how.
if u flash the MLG modem file from "ALL AT&T N3 Modems - Odin & Recovery Flashable" then i get my IMEI back with Baseband - " N900AUCUCMLG "

 

[carl1961]

But my question is , i am doing same as of u said. but whenever i flash the NCUC2 firmware my imei become null and Baseband also shows unknown. just i am wondering how.
if u flash the MLG modem file from "ALL AT&T N3 Modems - Odin & Recovery Flashable" then i get my IMEI back with Baseband - " N900AUCUCMLG "

I do not understand your issue, all the times I have installed ROM's and firmware on my phones I never even checked my IMEI, so what the reason your having to check your IMEI.

 

[resac]

I do not understand your issue, all the times I have installed ROM's and firmware on my phones I never even checked my IMEI, so what the reason your having to check your IMEI.

now i m in NJ5


but same even i flashed the kernel but its not shown the CP, so flashed MLG and here i am........

after flashing NJ5 Modem here is the result --->

 

[carl1961]

now i m in NJ5


but same even i flashed the kernel but its not shown the CP, so flashed MLG and here i am........

after flashing NJ5 Modem here is the result --->

Intall the nj5 firmware

https://mega.co.nz/#!CNMGDKaB!g2x607AzsKhcVtwcuCYZbJH0YjqEXheSV07lPctNqwg