Firmware for platform MTCD-MTCE Rockchip PX3-RK3188 1024x600 800x480 based on the latest official version of HCT2.
This is the further development of my Mod v1.x based on Android 5. Thanks graviton.no for the equipment provided for development. Nougat for ALL RK3188/PX3.
You can install this firmware on your radio, if in Settings > About machine >
The model starts with px3
The Android version starts with 7.1.
The chip version starts with MTCD or MTCE. Then there can be any letters, two, three, four - it does not matter.
Machine status example:
Or, if in Settings > About device > Version info>
The MCU version starts with MTCD or MTCE. Then there can be any letters, two, three, four - it does not matter.
The Android version starts with 5.1.
The Build number starts with rk3188.
Version info example:
Also, to restore the radio, if something goes wrong, you should be able enter the recovery.
The main advantages and trends of development of this mod:
New features.
Correction of existing errors and imperfections of the stock.
Best responsiveness in comparison of the stock + the ability for the user to improve this indicator.
The customizability. All critical changes made on my taste, you can customize for yourself or do as it was in the stock.
All changes made directly in application code without the use of Xposed framework for best perfomance.
Stability.
The stock design.
The first boot takes less than one minute. When switching from any other firmware or from version 1.x, user data is cleared automatically!
If you are upgrading from a previous version of 2.x, you do not need to wipe. But it is recommended if any problems arise. Especially if you used microG in the previous version.
If you install without wiping the data on top of the previous version, the first boot may take several minutes. Depends on the number of third-party applications.
But be sure to go to "Mod settings" to apply the default settings.
After installing or updating the firmware, the HU will reboot one more time to complete the installation of Magisk.
How to install the firmware ?
Extract the nupdate.img file from the archive to the root of the USB flash drive or SD card. It must be formatted in FAT32.
Take out all the other flash drives, SD cards, modems and other devices from the radio jacks.
Insert the USB flash drive into the USB connector of the radio. It is desirable to use the connector in which it is defined as USB1 (can be seen, for example, in the player).
Or SD-card - in the GPS slot.
The radio will prompt "Firmware Updating".
Click "Install".
In addition, you can install the firmware through the System update in Settings.
Or through the recovery.
If you have an old version of the MCU, I highly recommend upgrading to the current version.
MTCE MCU can be installed instead of MTCD. (make sure the letters of the current MCU matches the one you flash!)
If you like my ROMs and you want to thank me, please consider making a donation. You can find required details on my website or just click here.
Download:
Version 2.5 Google Drive
Improved screensaver:
Made displaying covers for most third-party players and radio station icons for PCRADIO app.
For correct work, I recommend adding your players to the "List of applications that should not work simultaneously".
Made displaying recommendations when driving along a route for Yandex.Navigator, Yandex.Maps, Google Maps, Sygic GPS Navigation & Maps.
Made displaying temperature from Yandex.Weather, if the data on the temperature does not come from the CAN-adapter.
Now the screensaver is correctly displayed in 800x480.
While the screensaver is running, the stock volume control is no longer shown.
Added pop-up messages from BT Music and third-party media players. Third-party media players must be added to the appropriate list.
Added a list of applications that will work in immersive mode (full screen).
Made a separate list of navigation using TTS
Added the ability to assign the last launched navigation to the Navi button (to switch between navigation and player, for example).
By popular demand added custom parking lines. Thanks for Incognito+
Magisk updated to v18.1, Viper4Android updated to v2.7
Added new button codes to replace
OEM launchers with widgets can now be installed just all at once.
Much work has been done to ensure support for new basic firmware, although this is not visible from the outside.
Old versions
Version 2.4
Moved to the new base firmware from October 2018.
In exchange for SuperSU, another root (Magisk) is preinstalled. Do not update.
You can install additional modules to extend the functionality.
Added ability to edit the list of applications in the carousel that are switched with the Mode button.
Added the ability to replace applications that run instead of stock. You can have your radio button launch PCRadio etc.
Added speed dependant volume control.
Added color selection in the HCT screensaver.
Fixed bug with ringtone selection.
A new screensaver has been added that displays the time and date, information from most third-party players (not just regular ones), the volume level, the speed, and the temperature if this data is available.
To display the temperature you need a CAN adapter.
It is possible to customize the appearance of the screensaver: colors, background image, the maximum value for the speed indicator.
Added the ability to replace the codes of buttons located on the steering wheel and the front panel.
You can configure the actions that are performed when you press the buttons on the steering wheel, even if they are connected via a CAN adapter.
Added the ability to select a group of radio stations.
If you are traveling to another locality where other radio stations operate, you can select a different group and tune in the stations again.
And having come home, choose the default group again and your settings will be restored.
Added a list of applications that have access to USB-devices. It allows you to get rid of the annoying request for access.
For fans of Taskers, the ability to assign numbers 1-9, 0, and the characters * and # to the steering buttons is added.
Intent = "com.microntek.report.event"
Extra "type" = "key"
Extra "value" = button code.
The name of the artist was added to the pop-up message from Music, and the frequency from the message from Radio.
Added an equalizer call for a long tap to the on-screen button of presets in Music.
The checkbox "Switching folders in Music with buttons on the steering wheel" is removed, since now the buttons on the steering wheel can be customized.
Replaced sysinit system - scripts in init.d are now executed in parallel.
Updated microG to latest version.
A short press on the on-screen power button now turns on the selected screensaver.
Added MTCDialer application for calls from third-party applications.
The Google app now calls via MTCDialer without additional settings.
You can muffle music by navigation application that play voice prompts through a speech synthesizer.
To use, you need to add the application to the "List of navigational applications that muffle other sounds" and select "Text-to-speech engine that muffle other sounds"
Replaced icons in the regular launcher and in the status bar.
Added the ability to call System UI Tuner from Mod Settings.
Added the ability to replace new button codes for a joystick in a Mazda car.
Other minor changes aimed at improving stability and usability.
Version 2.3
Moved to the new base firmware from April 2018.
Made a list of applications that allow the screen saver to be started.
You can add a third-party launcher or player to it, for example.
Added the ability to switch tracks in third-party players using the steering wheel buttons for owners of CAN-adapters for Mercedes cars, etc.
Made a list of applications that are restarted after sleep.
I included the PCRadio application in it. Now it always starts playback correctly after exiting sleep, if it was started when HU go to sleep.
In PCRadio's settings, you must enable the "Resume playback when application starts" switch. Also it is necessary to remove it from the whitelist if it was added to it.
Editing the whitelist now does not require a restart of the HU.
Added a volume control in the style typical for AV equipment from the 7floor module
Added the ability to display the volume control at the top, middle or bottom of the screen.
Added the ability to adjust the time during which the volume control remains on the screen after changing the volume value.
Has been made a list of applications that should not work simultaneously.
This list is an extension of the corresponding system list.
If one of the applications included in this list is launched, then the rest are closed.
That is, for example, if you include the same PCRadio, then it will close when you start the stock Music or Radio. And vice versa.
Added the ability to move the statusbar to the bottom of the screen. (Experimental option.)
Changed the logic of the name request for the button of the stored radio station.
If the name for the stored frequency is not specified earlier, text from the RDS is suggested.
Other changes aimed at improving stability.
Version 2.2.1 OTA-package
Added the ability to disable switching folders in the Music by the buttons on the steering wheel.
Fixed interface display for 800x480 resolution.
Version 2.2
In audioplayer added a jump to the previous / next folder on the seekdown / seekup steering wheel buttons and a on the long tap to the prev / next screen buttons.
Added folder name display to the pop-up message when switching between folders.
Made a list of navigational apps that muffle other sounds when playing voice prompts.
The list should include all navigation applications, including the one that is set by default to the Navi button.
Added application F-Droid for automatic update microG.
Added the ability to hide storage icons in the statusbar.
Updated the time zones to version 2018d.
After updating without a wipe, make sure that the time zone is set correctly.
Other changes, to improve stability.
Version 2.1
Moved to the new base firmware from February 2018.
The possibility of OTA-updates is added.
Added the ability to lock device as a regular Android device.
The lock is turned on after rebooting or exiting from sleep.
You can also turn on the lock after the Android screensaver has triggered or manually from the shutdown menu.
Sorting in alphabetical order of all lists in players is done.
Added pop-up messages showing information about the current radio station and music file. It is possible to set the font size and the duration of the messages.
The audio player goes to the next folder in the list after the playing the last file in the current folder in the sequential play mode.
Added a request for a name for the button of the stored radio station.
Added the ability to choose from eight screensavers. Pictures here.
Added the ability to turn off the full-screen keyboard.
Added the ability to turn off the restarting applications that worked before going to sleep.
In the application "Wheelkey Study" added actions "turn off the screen backlight", "recent applications" and "F-Cam application".
In third-party applications preinstalled "sound improver" ViPER4Android.
In the OEM added 5 launchers and their widgets (AY, HCT2, HCT3, KGL, ZH). Selection of the launcher after installation is made as usual, by pressing the Home button, as in the phone.
Unfortunately, Android 7 does not allow third-party applications to automatically create widgets.
Therefore we do this:
Install widgets and launcher APKs. Add any widget and give permission (see Screenshot).
Then remove the launcher and install it again. Or clear the launcher's data.
In the folder with the launcher HCT2 added weather from vitarkananda. Works only with this launcher.
Other changes, to improve stability.
Ideas of some improvements are taken from the module xposed-mtce-utils and other modules with the permission of the author, MVG-V70. For which I thank him very much.
But they are implemented without using the Xposed framework.
Version 2.0
All interface changes are also made for screen resolution 800x480.
The firmware is completely re-odexed with optimization for the px3 processor.
The Mod settings are made in a separate application, also available from the "Extra settings" in the Settings app.
Added the ability to replace Gapps on a microG with a lightened Play Market and back, at any time. It's extremely speed up the device, actual for 1 GB of RAM.
Located in the Mod settings.
Allowed autoloading of third-party applications when the device starts. (Torque, etc.)
Fixed playback of voice alerts in the standard voice package in Mapcam.info.
Removed the "red text", which appeared, if you flash the firmware on the radio, where was Android 5.
The internal memory is expanded on 256MB.
Preinstalled root and SuperSU.
Added support for init.d
The default is:
English language and date format, time zone CET.
Watching video whle driving - enabled
Bluetooth Password - 1234
Mixing level - 4
GPS time update - enabled
Navigation sound mode - mixing
Timeout of the screen saver - 1 minute, options added: 2 minutes, 10 and 30 minutes.
Added the ability to choose the speed at which the video will be blocked
Deny connection to data services in roaming.
Volume when reversing -4
Brightness of the screen at night - 20%
Unnecessary applications and files were deleted:
Open Wnn
Built-in Pico TTS speech synthesizer
WAP Push Manager
Corporate profiles
EasyConnected
Android live wallpapers (the ability to install your own Live wallpaper is left)
GPSTest replaced with GPS Test Plus
Google Maps has been moved from system applications to third-party applications. Now you can simply delete them in Settings if they are not needed.
Also, in third-party applications preinstalled Google Text-to-speech Engine. Speech synthesis works without connecting to the network.
Synchronization of Contacts and Calendar is added.
Time Zones updated to the latest version.
The built-in Contacts application is enabled.
Allowed to install applications not from the Play Market.
The Daydream functionality is enabled. This allows you to install any screensaver from the Play Market without stopping at one.
By default, the Clock screensaver from Android is selected. Color can be changed.
Any third-party screensaver is turned off under the same conditions as the standard one (touching the screen, switching cameras, etc.)
Android screensaver can be turned off, then the standard screensaver will work.
In the Bluetooth application, the name field is enlarged in the phone book. Added the recognition of the OBD adapter based on the settings so that the system distinguishes them from the phones and works with them correctly.
It is necessary, if your adapter does not have the letters OBD in the name.
In the Video application, the playlist is enlarged.
Repeat is disabled by default.
In the Music application, the playlist is enlarged and the repeat is disabled by default.
Instead of a spinning plate, a square fixed cover is made, loading of lyrics from the network is included,
the player is paused for an incoming call and the Mute button is pressed.
Radio - the running RDS text has been removed from the saved stations buttons. Now we can assign names to saved stations.
Fixed Bluetooth.
Now normally works those diagnostic programs that previously wrote that Bluetooth is turned off, offered to turn it on and hang up.
Programs automatically detect a previously paired adapter.
The on-screen power button in the status bar is made.
Single click to turn on the screen saver.
Double click to make a screenshot.
Triple click to kill the active application.
Long press - shutdown menu.
Added items in the shutdown menu : Restart, Safe mode, Recovery mode.
Added the ability to change the ringtone to any in the ringtones folder (only for the MD725 Bluetooth module)
Added the possibility of increasing TTL by default to bypass restrictions on the distribution of Internet from mobile devices.
Added a white list of applications that do not close when going to sleep, with the ability to configure.
The number on the volume control is increased and made white.
Added hidden item "Developer options" in settings.
The Status item is added in Settings - About machine.
Added the ability to disable some statusbar elements.
By default, the Home button, the Volume, Eject and Brightness icons are disabled. The Back button is moved from right to left. Everything can be configured, as it was in the stock or in another way.
Known issue: On devices with 1 GB due to lack of RAM or another videocodec hardware, the built-in video player and other programs that work with video does not work normally.
Solution: use a third-party video player.
How to automatically install your favorite APKs after flashing ?
Create a hct folder on a USB flash drive with firmware.
In this folder create folder apk.
Put your favorite APKs in this folder, they will be automatically installed after flashing.
How to switch to microG ?
Go to Mod Settings > Framework selection and select microG option. Changes take effect immediately !
The device will restart multiple times.
Then run the microG Settings app, give the necessary permissions and enable Google device registration and Google Cloud Messaging.
If you have GSM modem connected to your radio, go to UnifiedNlp Settings and turn on Mozilla Location Service in "Configure location backends" and Nominatim in "Configure address lookup backends".
Then go to Self-Check and verify that all the checkboxes are enabled (the check boxes in the lower part is only available with GSM modem).
Recreate Google account.
How to install this firmware instead of Android 5.1.1 ?
Download the attached archive with the SD_Firmware_Tool utility and unpack it.
Prepare a micro SD card for 2 - 4 - 8 Gb. It will be completely overwritten.
Prepare USB flash drive with the same firmware.
Insert the card into the PC card reader and run SD_Firmware_Tool.exe as Administrator.
Choose the removable disk.
Clear the "Upgrade Firmware" check box. It's important !
Press the "Firmware" button and select nupdate.img file.
Press the "Create" button and wait for the process to finish.
Insert this card into the "GPS" slot on the radio.
Insert the USB flash drive with the same firmware into the USB slot on the radio.
Hard reboot or turn off and turn on the power of the radio.
The radio will boot the recovery from Android 7 from the card and will go to the menu.
Select "Apply system image from SD card or USB"> "From usb storage"
Wait for the flashing process to finish.
Then select "Wipe data/factory reset"
Then "Reboot system now"
Radio will ask you to remove the SD card. Remove that.
Radio will boot to Android 7.
Note: You must Restore this card with the SD_Firmware_Tool utility for future use.
You can return to Android 5 in the same way.
So I apologize if this is a stupid question, but I'm still learning these units. Will this absolutely not work on an rk3066? I know it specifically states rk3188, but I've read that the two CPUs can be swapped internally without issue, so in my mind it seems that any ROMs for one are compatible with the other. I'm sure it's more complicated than that, but I figured I'd ask.
I'm using Malaysk's rom at the moment, but I'd like to have working Daydream. Thanks.
So I apologize if this is a stupid question, but I'm still learning these units. Will this absolutely not work on an rk3066? I know it specifically states rk3188, but I've read that the two CPUs can be swapped internally without issue, so in my mind it seems that any ROMs for one are compatible with the other. I'm sure it's more complicated than that, but I figured I'd ask.
I'm using Malaysk's rom at the moment, but I'd like to have working Daydream. Thanks.
Insert this card into the "GPS" slot on the radio.
Insert the USB flash drive with the same firmware into the USB slot on the radio.
Hard reboot or turn off and turn on the power of the radio.
The radio will boot the recovery from Android 7 from the card and will go to the menu.
@Hal9k_ - I ve installed your test Nougat ROM on several 1Gb RK3188/PX3 devices and the only way it will work is if the bootable SD card is removed AS SOON as "Nougat" appears on the screen, then it will boot into Nougat recovery. If this is not done then it will say "error" on screen and will not install the update, it took me hours to figure this out !
Or have you made a change so the card does not have to be ejected straight away ?
@Hal9k_ - I ve installed your test Nougat ROM on several 1Gb RK3188/PX3 devices and the only way it will work is if the bootable SD card is removed AS SOON as "Nougat" appears on the screen, then it will boot into Nougat recovery. If this is not done then it will say "error" on screen and will not install the update, it took me hours to figure this out !
Or have you made a change so the card does not have to be ejected straight away ?
Yes I did, I only ever use that option, pretty sure one other user had the problem as well, we both couldnt get it to work for days, then I managed to by ejecting the sd card as soon as "Nougat" appeared on screen.
I thought the whole point of using sd firmware tools was to make a Lollipop unit boot into Nougat recovery ?
I have an RK3368/PX5 now, but I will be installing this on a friend's Lollipop unit later, I ll make a new bootable sd card with your new ROM, maybe it wont happen with the new version ?
I ll let you know how I get on.
You only have a 2Gb RK3188/PX3 SoM now ?
Youve sold your 1Gb RK3188/PX3 SoM ?
(Starts to think of ways to get Hal9k_ to make a version of his amazing ROM for the RK3368/PX5 . . . . )
Yes I did, I only ever use that option, pretty sure one other user had the problem as well, we both couldnt get it to work for days, then I managed to by ejecting the sd card as soon as "Nougat" appeared on screen.
I have an RK3368/PX5 now, but I will be installing this on a friend's Lollipop unit later, I ll make a new bootable sd card with your new ROM, maybe it wont happen with the new version ?
Yes, I ll try with your latest version, but it would only work if the sd card was ejected as soon as Nougat appeared on the screen with your first de-odexed/rooted Nougat test version form a few months back.
2 2Gb SoMs !! ?? You should sell one and get an RK3368/PX5 SoM too, so you have one of each !
Yes, there can be no mistake that its a ROM thread now.
You could put "Nougat for ALL RK3188/PX3" units somewhere in the title too ? It would attract more users - no one can tell from the title at the moment that it is Nougat for all PX3 devices at the moment.
Sorry to keep criticising your thread title, I just want as many people to use your ROM as possible.
I take it youre on 4pda.ru as well and their users know about your excellent work too ?
You could put "Nougat for ALL RK3188/PX3" units somewhere in the title too ? It would attract more users - no one can tell from the title at the moment that it is Nougat for all PX3 devices at the moment and the fact that it is Nougat for 1Gb SoMs will attract many people.
Sorry to keep criticising your thread title, I just want as many people to use your ROM as possible.
You are neglecting RK3368/PX5 users, we are all desperate for your genius on our units
Firmware for platform MTCD-MTCE Rockchip PX3-RK3188 1024x600 800x480 based on the latest official version of HCT2.
This is the further development of my Mod v1.x based on Android 5. Thanks graviton.no for the equipment provided for development. Nougat for ALL RK3188/PX3.
You can install this firmware on your radio, if in Settings > About machine >
The model starts with px3
The Android version starts with 7.1.
The chip version starts with MTCD or MTCE. Then there can be any letters, two, three, four - it does not matter.
Machine status example:
Or, if in Settings > About device > Version info>
The MCU version starts with MTCD or MTCE. Then there can be any letters, two, three, four - it does not matter.
The Android version starts with 5.1.
The Build number starts with rk3188.
Version info example:
Also, to restore the radio, if something goes wrong, you should be able enter the recovery.
The main advantages and trends of development of this mod:
New features.
Correction of existing errors and imperfections of the stock.
Best responsiveness in comparison of the stock + the ability for the user to improve this indicator.
The customizability. All critical changes made on my taste, you can customize for yourself or do as it was in the stock.
All changes made directly in application code without the use of Xposed framework for best perfomance.
Stability.
The stock design.
The first boot takes less than one minute. When switching from any other firmware or from version 1.x, user data is cleared automatically!
If you are upgrading from a previous version of 2.x, you do not need to wipe. But it is recommended if any problems arise. Especially if you used microG in the previous version.
If you install without wiping the data on top of the previous version, the first boot may take several minutes. Depends on the number of third-party applications.
But be sure to go to "Mod settings" to apply the default settings.
After installing or updating the firmware, the HU will reboot one more time to complete the installation of Magisk.
How to install the firmware ?
Extract the nupdate.img file from the archive to the root of the USB flash drive or SD card. It must be formatted in FAT32.
Take out all the other flash drives, SD cards, modems and other devices from the radio jacks.
Insert the USB flash drive into the USB connector of the radio. It is desirable to use the connector in which it is defined as USB1 (can be seen, for example, in the player).
Or SD-card - in the GPS slot.
The radio will prompt "Firmware Updating".
Click "Install".
In addition, you can install the firmware through the System update in Settings.
Or through the recovery.
If you have an old version of the MCU, I highly recommend upgrading to the current version.
MTCE MCU can be installed instead of MTCD. (make sure the letters of the current MCU matches the one you flash!)
If you like my ROMs and you want to thank me, please consider making a donation. You can find required details on my website or just click here.
Download:
Version 2.5 Google Drive
Improved screensaver:
Made displaying covers for most third-party players and radio station icons for PCRADIO app.
For correct work, I recommend adding your players to the "List of applications that should not work simultaneously".
Made displaying recommendations when driving along a route for Yandex.Navigator, Yandex.Maps, Google Maps, Sygic GPS Navigation & Maps.
Made displaying temperature from Yandex.Weather, if the data on the temperature does not come from the CAN-adapter.
Now the screensaver is correctly displayed in 800x480.
While the screensaver is running, the stock volume control is no longer shown.
Added pop-up messages from BT Music and third-party media players. Third-party media players must be added to the appropriate list.
Added a list of applications that will work in immersive mode (full screen).
Made a separate list of navigation using TTS
Added the ability to assign the last launched navigation to the Navi button (to switch between navigation and player, for example).
By popular demand added custom parking lines. Thanks for Incognito+
Magisk updated to v18.1, Viper4Android updated to v2.7
Added new button codes to replace
OEM launchers with widgets can now be installed just all at once.
Much work has been done to ensure support for new basic firmware, although this is not visible from the outside.
Old versions
Version 2.4
Moved to the new base firmware from October 2018.
In exchange for SuperSU, another root (Magisk) is preinstalled. Do not update.
You can install additional modules to extend the functionality.
Added ability to edit the list of applications in the carousel that are switched with the Mode button.
Added the ability to replace applications that run instead of stock. You can have your radio button launch PCRadio etc.
Added speed dependant volume control.
Added color selection in the HCT screensaver.
Fixed bug with ringtone selection.
A new screensaver has been added that displays the time and date, information from most third-party players (not just regular ones), the volume level, the speed, and the temperature if this data is available.
To display the temperature you need a CAN adapter.
It is possible to customize the appearance of the screensaver: colors, background image, the maximum value for the speed indicator.
Added the ability to replace the codes of buttons located on the steering wheel and the front panel.
You can configure the actions that are performed when you press the buttons on the steering wheel, even if they are connected via a CAN adapter.
Added the ability to select a group of radio stations.
If you are traveling to another locality where other radio stations operate, you can select a different group and tune in the stations again.
And having come home, choose the default group again and your settings will be restored.
Added a list of applications that have access to USB-devices. It allows you to get rid of the annoying request for access.
For fans of Taskers, the ability to assign numbers 1-9, 0, and the characters * and # to the steering buttons is added.
Intent = "com.microntek.report.event"
Extra "type" = "key"
Extra "value" = button code.
The name of the artist was added to the pop-up message from Music, and the frequency from the message from Radio.
Added an equalizer call for a long tap to the on-screen button of presets in Music.
The checkbox "Switching folders in Music with buttons on the steering wheel" is removed, since now the buttons on the steering wheel can be customized.
Replaced sysinit system - scripts in init.d are now executed in parallel.
Updated microG to latest version.
A short press on the on-screen power button now turns on the selected screensaver.
Added MTCDialer application for calls from third-party applications.
The Google app now calls via MTCDialer without additional settings.
You can muffle music by navigation application that play voice prompts through a speech synthesizer.
To use, you need to add the application to the "List of navigational applications that muffle other sounds" and select "Text-to-speech engine that muffle other sounds"
Replaced icons in the regular launcher and in the status bar.
Added the ability to call System UI Tuner from Mod Settings.
Added the ability to replace new button codes for a joystick in a Mazda car.
Other minor changes aimed at improving stability and usability.
Version 2.3
Moved to the new base firmware from April 2018.
Made a list of applications that allow the screen saver to be started.
You can add a third-party launcher or player to it, for example.
Added the ability to switch tracks in third-party players using the steering wheel buttons for owners of CAN-adapters for Mercedes cars, etc.
Made a list of applications that are restarted after sleep.
I included the PCRadio application in it. Now it always starts playback correctly after exiting sleep, if it was started when HU go to sleep.
In PCRadio's settings, you must enable the "Resume playback when application starts" switch. Also it is necessary to remove it from the whitelist if it was added to it.
Editing the whitelist now does not require a restart of the HU.
Added a volume control in the style typical for AV equipment from the 7floor module
Added the ability to display the volume control at the top, middle or bottom of the screen.
Added the ability to adjust the time during which the volume control remains on the screen after changing the volume value.
Has been made a list of applications that should not work simultaneously.
This list is an extension of the corresponding system list.
If one of the applications included in this list is launched, then the rest are closed.
That is, for example, if you include the same PCRadio, then it will close when you start the stock Music or Radio. And vice versa.
Added the ability to move the statusbar to the bottom of the screen. (Experimental option.)
Changed the logic of the name request for the button of the stored radio station.
If the name for the stored frequency is not specified earlier, text from the RDS is suggested.
Other changes aimed at improving stability.
Version 2.2.1 OTA-package
Added the ability to disable switching folders in the Music by the buttons on the steering wheel.
Fixed interface display for 800x480 resolution.
Version 2.2
In audioplayer added a jump to the previous / next folder on the seekdown / seekup steering wheel buttons and a on the long tap to the prev / next screen buttons.
Added folder name display to the pop-up message when switching between folders.
Made a list of navigational apps that muffle other sounds when playing voice prompts.
The list should include all navigation applications, including the one that is set by default to the Navi button.
Added application F-Droid for automatic update microG.
Added the ability to hide storage icons in the statusbar.
Updated the time zones to version 2018d.
After updating without a wipe, make sure that the time zone is set correctly.
Other changes, to improve stability.
Version 2.1
Moved to the new base firmware from February 2018.
The possibility of OTA-updates is added.
Added the ability to lock device as a regular Android device.
The lock is turned on after rebooting or exiting from sleep.
You can also turn on the lock after the Android screensaver has triggered or manually from the shutdown menu.
Sorting in alphabetical order of all lists in players is done.
Added pop-up messages showing information about the current radio station and music file. It is possible to set the font size and the duration of the messages.
The audio player goes to the next folder in the list after the playing the last file in the current folder in the sequential play mode.
Added a request for a name for the button of the stored radio station.
Added the ability to choose from eight screensavers. Pictures here.
Added the ability to turn off the full-screen keyboard.
Added the ability to turn off the restarting applications that worked before going to sleep.
In the application "Wheelkey Study" added actions "turn off the screen backlight", "recent applications" and "F-Cam application".
In third-party applications preinstalled "sound improver" ViPER4Android.
In the OEM added 5 launchers and their widgets (AY, HCT2, HCT3, KGL, ZH). Selection of the launcher after installation is made as usual, by pressing the Home button, as in the phone.
Unfortunately, Android 7 does not allow third-party applications to automatically create widgets.
Therefore we do this:
Install widgets and launcher APKs. Add any widget and give permission (see Screenshot).
Then remove the launcher and install it again. Or clear the launcher's data.
In the folder with the launcher HCT2 added weather from vitarkananda. Works only with this launcher.
Other changes, to improve stability.
Ideas of some improvements are taken from the module xposed-mtce-utils and other modules with the permission of the author, MVG-V70. For which I thank him very much.
But they are implemented without using the Xposed framework.
Version 2.0
All interface changes are also made for screen resolution 800x480.
The firmware is completely re-odexed with optimization for the px3 processor.
The Mod settings are made in a separate application, also available from the "Extra settings" in the Settings app.
Added the ability to replace Gapps on a microG with a lightened Play Market and back, at any time. It's extremely speed up the device, actual for 1 GB of RAM.
Located in the Mod settings.
Allowed autoloading of third-party applications when the device starts. (Torque, etc.)
Fixed playback of voice alerts in the standard voice package in Mapcam.info.
Removed the "red text", which appeared, if you flash the firmware on the radio, where was Android 5.
The internal memory is expanded on 256MB.
Preinstalled root and SuperSU.
Added support for init.d
The default is:
English language and date format, time zone CET.
Watching video whle driving - enabled
Bluetooth Password - 1234
Mixing level - 4
GPS time update - enabled
Navigation sound mode - mixing
Timeout of the screen saver - 1 minute, options added: 2 minutes, 10 and 30 minutes.
Added the ability to choose the speed at which the video will be blocked
Deny connection to data services in roaming.
Volume when reversing -4
Brightness of the screen at night - 20%
Unnecessary applications and files were deleted:
Open Wnn
Built-in Pico TTS speech synthesizer
WAP Push Manager
Corporate profiles
EasyConnected
Android live wallpapers (the ability to install your own Live wallpaper is left)
GPSTest replaced with GPS Test Plus
Google Maps has been moved from system applications to third-party applications. Now you can simply delete them in Settings if they are not needed.
Also, in third-party applications preinstalled Google Text-to-speech Engine. Speech synthesis works without connecting to the network.
Synchronization of Contacts and Calendar is added.
Time Zones updated to the latest version.
The built-in Contacts application is enabled.
Allowed to install applications not from the Play Market.
The Daydream functionality is enabled. This allows you to install any screensaver from the Play Market without stopping at one.
By default, the Clock screensaver from Android is selected. Color can be changed.
Any third-party screensaver is turned off under the same conditions as the standard one (touching the screen, switching cameras, etc.)
Android screensaver can be turned off, then the standard screensaver will work.
In the Bluetooth application, the name field is enlarged in the phone book. Added the recognition of the OBD adapter based on the settings so that the system distinguishes them from the phones and works with them correctly.
It is necessary, if your adapter does not have the letters OBD in the name.
In the Video application, the playlist is enlarged.
Repeat is disabled by default.
In the Music application, the playlist is enlarged and the repeat is disabled by default.
Instead of a spinning plate, a square fixed cover is made, loading of lyrics from the network is included,
the player is paused for an incoming call and the Mute button is pressed.
Radio - the running RDS text has been removed from the saved stations buttons. Now we can assign names to saved stations.
Fixed Bluetooth.
Now normally works those diagnostic programs that previously wrote that Bluetooth is turned off, offered to turn it on and hang up.
Programs automatically detect a previously paired adapter.
The on-screen power button in the status bar is made.
Single click to turn on the screen saver.
Double click to make a screenshot.
Triple click to kill the active application.
Long press - shutdown menu.
Added items in the shutdown menu : Restart, Safe mode, Recovery mode.
Added the ability to change the ringtone to any in the ringtones folder (only for the MD725 Bluetooth module)
Added the possibility of increasing TTL by default to bypass restrictions on the distribution of Internet from mobile devices.
Added a white list of applications that do not close when going to sleep, with the ability to configure.
The number on the volume control is increased and made white.
Added hidden item "Developer options" in settings.
The Status item is added in Settings - About machine.
Added the ability to disable some statusbar elements.
By default, the Home button, the Volume, Eject and Brightness icons are disabled. The Back button is moved from right to left. Everything can be configured, as it was in the stock or in another way.
Known issue: On devices with 1 GB due to lack of RAM or another videocodec hardware, the built-in video player and other programs that work with video does not work normally.
Solution: use a third-party video player.
How to automatically install your favorite APKs after flashing ?
Create a hct folder on a USB flash drive with firmware.
In this folder create folder apk.
Put your favorite APKs in this folder, they will be automatically installed after flashing.
How to switch to microG ?
Go to Mod Settings > Framework selection and select microG option. Changes take effect immediately !
The device will restart multiple times.
Then run the microG Settings app, give the necessary permissions and enable Google device registration and Google Cloud Messaging.
If you have GSM modem connected to your radio, go to UnifiedNlp Settings and turn on Mozilla Location Service in "Configure location backends" and Nominatim in "Configure address lookup backends".
Then go to Self-Check and verify that all the checkboxes are enabled (the check boxes in the lower part is only available with GSM modem).
Recreate Google account.
How to install this firmware instead of Android 5.1.1 ?
Download the attached archive with the SD_Firmware_Tool utility and unpack it.
Prepare a micro SD card for 2 - 4 - 8 Gb. It will be completely overwritten.
Prepare USB flash drive with the same firmware.
Insert the card into the PC card reader and run SD_Firmware_Tool.exe as Administrator.
Choose the removable disk.
Clear the "Upgrade Firmware" check box. It's important !
Press the "Firmware" button and select nupdate.img file.
Press the "Create" button and wait for the process to finish.
Insert this card into the "GPS" slot on the radio.
Insert the USB flash drive with the same firmware into the USB slot on the radio.
Hard reboot or turn off and turn on the power of the radio.
The radio will boot the recovery from Android 7 from the card and will go to the menu.
Select "Apply system image from SD card or USB"> "From usb storage"
Wait for the flashing process to finish.
Then select "Wipe data/factory reset"
Then "Reboot system now"
Radio will ask you to remove the SD card. Remove that.
Radio will boot to Android 7.
Note: You must Restore this card with the SD_Firmware_Tool utility for future use.
You can return to Android 5 in the same way.
added custom parking lines. Thanks for Incognito+
