Just got the YTF Aramid case from amazon to replace the VRS pro stand case. Wow am I impressed. The fit is perfect and adds no bulk at all. Added one of these cheap kickstands for $6. Works perfectly along with wireless charging. Very happy with this purchase.
Accessories Samsung Galaxy Z Fold3 Case Thread
- Thread starter bigup7
- Start date
I would love to see something that combines elements of these two cases,
www.spigen.com
Galaxy Z Fold 3 Case Thin Fit P
Guard your Galaxy Z Fold 3 with our pen design slim Case. The Thin Fit P lets you express your creativity with a slot to store your stylus while providing protection to your phone. Shop now.
Well, if you place the stylus slots on either of the sides, then it'll make the phone wider.
I currently have the Spigen Air Skin (It ads very little bulk to the device.
www.spigen.com
Find it on Amazon, it's about half off list cost.
Galaxy Z Fold 3 Case AirSkin
Protect your Galaxy Z Fold 3 with one of the thinnest cases on the market. The AirSkin redefines slim cases and is perfect for the minimalist that wants device defense without adding any unnecessary bulk. Shop online today!
My ideal case would hold the spen, but not on the rear of the device. Would have a cover for the front screen (like a folio case). And would have space for credit cards. And also ideally not fake leather, it looks like my Moms wallet.
I know it would end up being about 2 inches thick, but for my use case scenario would be ideal.
I know it would end up being about 2 inches thick, but for my use case scenario would be ideal.
No, case is very strong and I've read that people remove and reposition the stand to find the right placement.
#Fold3 #CaseMod
So all you case modders out there, I'm joining the club! Finally had it with my official flappy bit S-Pen case. Tried a bunch of aftermarket options but wasn't happy with the fit and finish or branding on any of them. So I got the official silicone cover courtesy of Samsung and my points. Attached my ESR all metal kickstand next to the camera to leave the wireless charging coil exposed. Also I shaved off the channel locking mechanism from the official S-Pen holder and attached that all the way to the side also to leave the charging pad exposed. Still gets in the way of most wireless charging pads but I've got a 1.6" coil that I'm going to use to build my own custom charging stand with a cutout for the pen. Tested it loose and it works fine. And no sloppy super glue here. Kickstand and pen holder are both attached using 3m 300lse tape (the same stuff that holds your screen onto your phone) cut to precise dimensions, with the edge recessed enough that it isn't picking up every stray hair and spec of dust. I scuffed up and prepped both surfaces with primer 94 for better adhesion. The pen holder seems to be made of the same material as the silicone cover so the whole thing (minus the kickstand) looks like an official case. When the phone is unfolded and laid flat, the pen holder acts as a fulcrum to angle the whole thing slightly like a professional drawing tablet, and no rocking. Kickstand can be used to stand the phone while folded or unfolded, both orientations, and can even be used to lay the phone flat unfolded for a nice 30° angle for writing/drawing. Gotta let the 300LSE cure for 24 hours to make a good bond to the silicone.
So all you case modders out there, I'm joining the club! Finally had it with my official flappy bit S-Pen case. Tried a bunch of aftermarket options but wasn't happy with the fit and finish or branding on any of them. So I got the official silicone cover courtesy of Samsung and my points. Attached my ESR all metal kickstand next to the camera to leave the wireless charging coil exposed. Also I shaved off the channel locking mechanism from the official S-Pen holder and attached that all the way to the side also to leave the charging pad exposed. Still gets in the way of most wireless charging pads but I've got a 1.6" coil that I'm going to use to build my own custom charging stand with a cutout for the pen. Tested it loose and it works fine. And no sloppy super glue here. Kickstand and pen holder are both attached using 3m 300lse tape (the same stuff that holds your screen onto your phone) cut to precise dimensions, with the edge recessed enough that it isn't picking up every stray hair and spec of dust. I scuffed up and prepped both surfaces with primer 94 for better adhesion. The pen holder seems to be made of the same material as the silicone cover so the whole thing (minus the kickstand) looks like an official case. When the phone is unfolded and laid flat, the pen holder acts as a fulcrum to angle the whole thing slightly like a professional drawing tablet, and no rocking. Kickstand can be used to stand the phone while folded or unfolded, both orientations, and can even be used to lay the phone flat unfolded for a nice 30° angle for writing/drawing. Gotta let the 300LSE cure for 24 hours to make a good bond to the silicone.
Nice! I did something similar with the Spigen Slim Armor Pro and the Samsung portfolio cases Pen/holder. I wanted hinge protection, S-Pen slot and a kickstand. The kickstand is the "ESR kickstand" from Amazon & the Pen slot was removed from the Samsung Pen portfolio case which I adhered with J-B plastic weld to the Spigen Slim Armor Pro's hinge. Feels pretty solid, I'm happy with it and wireless charging still works!
Attachments
Nice and thanks for the pic.
I also ordered a kickstand couple days ago for sticking it on my Aramid case.
I like the Spigen Air Skin https://smile.amazon.com/gp/product/B0938NB5PB/ref=ox_sc_act_title_2?smid=A2SFKRF5TPZMT5&psc=1 for it's slim design but the included tape does not do the job. Has anyone tried using silicone to hold especially the face plate on? The back seams fine with tape.
I moved my kickstand up near the camera like a couple of you have done with the ESR stand. I do like it better up there. I've also ordered the ESR stand as I like the looks better and it's a touch thinner, but I see that it doesn't open up as wide as this cheap stand.
Attachments
I ordered one of these a while ago and it finally came in. I got to say I am pretty happy with it especially for the price. Of course it's not the highest quality but it fits just fine and functions precisely how I hoped it would. With the pen inserted it definitely affects wireless charging but if I get it just right it will work. This is a generic unbranded case being sold everywhere online.
For Samsung Galaxy Z Fold 3 5G Leather Kickstand Case Cover With S Pen Holder | eBay
The luxury shell case is made of premium PU Litchi Grain Leather material. It can be easily compatible with different sizes of s pen,(NOT included S Pen). Situated in California since we began the organization in 2013, we utilize more than 50 staff and works through workplaces.
www.ebay.com
Case looks great, but the metal kickstand is right over the charge pad. That can't be good for wireless charging speed.I ordered one of these a while ago and it finally came in. I got to say I am pretty happy with it especially for the price. Of course it's not the highest quality but it fits just fine and functions precisely how I hoped it would. With the pen inserted it definitely affects wireless charging but if I get it just right it will work. This is a generic unbranded case being sold everywhere online.
For Samsung Galaxy Z Fold 3 5G Leather Kickstand Case Cover With S Pen Holder | eBay
The luxury shell case is made of premium PU Litchi Grain Leather material. It can be easily compatible with different sizes of s pen,(NOT included S Pen). Situated in California since we began the organization in 2013, we utilize more than 50 staff and works through workplaces.www.ebay.com
Top Liked Posts
-
There are no posts matching your filters.
-
7I bought my case and already happy with it, official Samsung Aramid Cover.
Looks good, fits well, finally done for cover display too.6Hi guys. I didn't find a case I would like so I made myself this one "bumper" lightweight case on my 3d printer. On back, hinch and front sides I have sticker from Ali. On outer display I have tempered glass, but it's going off so I need to replace it. After that I will by happy. This is first time I was making 3d model from scratch so I spent a lot of time on it but I made everything exactly as I wanted and now I am satisfied
5
I did. I like the look and feel of it. My only concern is the protection. It is so thin I question its ability to protect the phone if it were dropped. That being said, it will be my daily case until something nice comes out with S Pen support (besides the Samsung Flip one, it's not a good option)
I placed a Ringke pen holder on the back to hold my S Pen.
