• Introducing XDA Computing: Discussion zones for Hardware, Software, and more!    Check it out!

[SHARED] Redmi 9 ENG rom (engineering rom)

Search This thread

razers211

Member
Jan 18, 2020
10
5
after further testing and finally restoring my IMEIs using this rom, i can say that it is indeed working, so hope it helps a lot of you guys stuck with a phone without IMEIs.
link :

Requirements:
- SP flash tool and right DA file (provided in the post).
-brom bypass (also provided).
-patience and perseverance.

Steps to install:
1)steps to install brom bypass:
-first install python 3 (check on google)
- then run this code in a cmd
Code:
pip install pyusb pyserial json5
-after that make sure to have all the mediatek drivers installed and install libusb from the archive i provided
- after installing libusb you will be greeted by a filter wizard window, check the "install new device filter" then connect the phone to the pc while pressing (volume +, volume - and power button) all at the same time you
will see in the list a new mtk com port appear click on it and then on install, done with the prep'.
2)steps to flash:
-first launch the brom bypass, a window will appear saying 'waiting for bootrom' connect your phone while pressing (volume +, volume - and power button) all together then you will see on the command prompt 'protection disabled' it means you have successfully bypassed the brom.
- now oppen up sp flash tool, select the download agent, select the scatter fille from the rom folder and the auth file (provided with sp flash tool archive on the post) then setup sp flash tool in uart mode with a bud rate of 921600 then flash in format all.
-done.

Hope this helped, cheers !
 

Attachments

  • SP flash tool.rar
    37 MB · Views: 544
  • libusb + BROM bypass.rar
    624.6 KB · Views: 464
Last edited:

willkurt27

Member
Feb 28, 2016
9
5
after further testing and finally restoring my IMEIs using this rom, i can say that it is indeed working, so hope it helps a lot of you guys stuck with a phone without IMEIs.
link :

Requirements:
- SP flash tool and right DA file (provided in the post).
-brom bypass (also provided).
-patience and perseverance.

Steps to install:
1)steps to install brom bypass:
-first install python 3 (check on google)
- then run this code in a cmd
Code:
pip install pyusb pyserial json5
-after that make sure to have all the mediatek drivers installed and install libusb from the archive i provided
- after installing libusb you will be greeted by a filter wizard window, check the "install new device filter" then connect the phone to the pc while pressing (volume +, volume - and power button) all at the same time you
will see in the list a new mtk com port appear click on it and then on install, done with the prep'.
2)steps to flash:
-first launch the brom bypass, a window will appear saying 'waiting for bootrom' connect your phone while pressing (volume +, volume - and power button) all together then you will see on the command prompt 'protection disabled' it means you have successfully bypassed the brom.
- now oppen up sp flash tool, select the download agent, select the scatter fille from the rom folder and the auth file (provided with sp flash tool archive on the post) then setup sp flash tool in uart mode with a bud rate of 921600 then flash in format all.
-done.

Hope this helped, cheers !
Help sir, how to fix this error? Thanks
 

Attachments

  • ss4.png
    ss4.png
    5.9 KB · Views: 163

willkurt27

Member
Feb 28, 2016
9
5
after further testing and finally restoring my IMEIs using this rom, i can say that it is indeed working, so hope it helps a lot of you guys stuck with a phone without IMEIs.
link :

Requirements:
- SP flash tool and right DA file (provided in the post).
-brom bypass (also provided).
-patience and perseverance.

Steps to install:
1)steps to install brom bypass:
-first install python 3 (check on google)
- then run this code in a cmd
Code:
pip install pyusb pyserial json5
-after that make sure to have all the mediatek drivers installed and install libusb from the archive i provided
- after installing libusb you will be greeted by a filter wizard window, check the "install new device filter" then connect the phone to the pc while pressing (volume +, volume - and power button) all at the same time you
will see in the list a new mtk com port appear click on it and then on install, done with the prep'.
2)steps to flash:
-first launch the brom bypass, a window will appear saying 'waiting for bootrom' connect your phone while pressing (volume +, volume - and power button) all together then you will see on the command prompt 'protection disabled' it means you have successfully bypassed the brom.
- now oppen up sp flash tool, select the download agent, select the scatter fille from the rom folder and the auth file (provided with sp flash tool archive on the post) then setup sp flash tool in uart mode with a bud rate of 921600 then flash in format all.
-done.

Hope this helped, cheers !
Help sir, how to fix this error? Thanks
 

Attachments

  • ss4.png
    ss4.png
    5.9 KB · Views: 59

yoalcuadrao

Member
Apr 2, 2017
6
0
after further testing and finally restoring my IMEIs using this rom, i can say that it is indeed working, so hope it helps a lot of you guys stuck with a phone without IMEIs.
link :

Requirements:
- SP flash tool and right DA file (provided in the post).
-brom bypass (also provided).
-patience and perseverance.

Steps to install:
1)steps to install brom bypass:
-first install python 3 (check on google)
- then run this code in a cmd
Code:
pip install pyusb pyserial json5
-after that make sure to have all the mediatek drivers installed and install libusb from the archive i provided
- after installing libusb you will be greeted by a filter wizard window, check the "install new device filter" then connect the phone to the pc while pressing (volume +, volume - and power button) all at the same time you
will see in the list a new mtk com port appear click on it and then on install, done with the prep'.
2)steps to flash:
-first launch the brom bypass, a window will appear saying 'waiting for bootrom' connect your phone while pressing (volume +, volume - and power button) all together then you will see on the command prompt 'protection disabled' it means you have successfully bypassed the brom.
- now oppen up sp flash tool, select the download agent, select the scatter fille from the rom folder and the auth file (provided with sp flash tool archive on the post) then setup sp flash tool in uart mode with a bud rate of 921600 then flash in format all.
-done.

Hope this helped, cheers !
Hi thank you i was succesfuly installed this rom and now what to restore IMEI? AT commands not working it says +CME ERROR: 100
 

hckbkl

Senior Member
Jun 12, 2021
89
7
76
Xiaomi Black Shark 4
after further testing and finally restoring my IMEIs using this rom, i can say that it is indeed working, so hope it helps a lot of you guys stuck with a phone without IMEIs.
link :

Requirements:
- SP flash tool and right DA file (provided in the post).
-brom bypass (also provided).
-patience and perseverance.

Steps to install:
1)steps to install brom bypass:
-first install python 3 (check on google)
- then run this code in a cmd
Code:
pip install pyusb pyserial json5
-after that make sure to have all the mediatek drivers installed and install libusb from the archive i provided
- after installing libusb you will be greeted by a filter wizard window, check the "install new device filter" then connect the phone to the pc while pressing (volume +, volume - and power button) all at the same time you
will see in the list a new mtk com port appear click on it and then on install, done with the prep'.
2)steps to flash:
-first launch the brom bypass, a window will appear saying 'waiting for bootrom' connect your phone while pressing (volume +, volume - and power button) all together then you will see on the command prompt 'protection disabled' it means you have successfully bypassed the brom.
- now oppen up sp flash tool, select the download agent, select the scatter fille from the rom folder and the auth file (provided with sp flash tool archive on the post) then setup sp flash tool in uart mode with a bud rate of 921600 then flash in format all.
-done.

Hope this helped, cheers !
thank very much bro
 

tiagoql

New member
Oct 30, 2015
1
0
muito obrigado, tive que usar o META modem para escrever IMEI. so deu certo com essa room, deus te abençoe. BRASIL

----------

MOD EDIT: English Translation Below

thank you very much, had to use META modem to write IMEI. it just worked out with this room, god bless you. BRAZIL
 
Last edited by a moderator:

lobothefoots

Member
Jun 13, 2010
40
0
after further testing and finally restoring my IMEIs using this rom, i can say that it is indeed working, so hope it helps a lot of you guys stuck with a phone without IMEIs.
link :

Hello and thanks for sharing, I have the same error as @willkurt27
while using SPFlash Tool

What I do:
Launch bypass.bat
Plug my phone with vol - pressed and battery unplugged.

[2021-08-24 21:33:09.958798] Waiting for device [2021-08-24 21:39:08.793257] Found device = 0e8d:0003 [2021-08-24 21:39:14.833772] Device hw code: 0x707 [2021-08-24 21:39:14.833772] Device hw sub code: 0x8a00 [2021-08-24 21:39:14.833772] Device hw version: 0xca00 [2021-08-24 21:39:14.833772] Device sw version: 0x0 [2021-08-24 21:39:14.833772] Device secure boot: True [2021-08-24 21:39:14.833772] Device serial link authorization: True [2021-08-24 21:39:14.833772] Device download agent authorization: True [2021-08-24 21:39:14.833772] Disabling watchdog timer [2021-08-24 21:39:14.849712] Disabling protection [2021-08-24 21:39:14.849712] Using kamakiri [2021-08-24 21:39:14.849712] Protection disabled Appuyez sur une touche pour continuer...

Then I use SPFlash Tool v5.1924.0
Tried with DA_6765_6785_6768_6873_6885_6853.bin and MTK_AllInOne_DA.bin


SPerror.PNG


What am I doing wrong?
 

kazuhiko23124

Member
Aug 21, 2021
27
2
Redmi 9
Hello and thanks for sharing, I have the same error as @willkurt27
while using SPFlash Tool

What I do:
Launch bypass.bat
Plug my phone with vol - pressed and battery unplugged.

[2021-08-24 21:33:09.958798] Waiting for device [2021-08-24 21:39:08.793257] Found device = 0e8d:0003 [2021-08-24 21:39:14.833772] Device hw code: 0x707 [2021-08-24 21:39:14.833772] Device hw sub code: 0x8a00 [2021-08-24 21:39:14.833772] Device hw version: 0xca00 [2021-08-24 21:39:14.833772] Device sw version: 0x0 [2021-08-24 21:39:14.833772] Device secure boot: True [2021-08-24 21:39:14.833772] Device serial link authorization: True [2021-08-24 21:39:14.833772] Device download agent authorization: True [2021-08-24 21:39:14.833772] Disabling watchdog timer [2021-08-24 21:39:14.849712] Disabling protection [2021-08-24 21:39:14.849712] Using kamakiri [2021-08-24 21:39:14.849712] Protection disabled Appuyez sur une touche pour continuer...

Then I use SPFlash Tool v5.1924.0
Tried with DA_6765_6785_6768_6873_6885_6853.bin and MTK_AllInOne_DA.bin


View attachment 5392951

What am I doing wrong?
try to insert the auth file
 

kazuhiko23124

Member
Aug 21, 2021
27
2
Redmi 9
Hello and thanks for sharing, I have the same error as @willkurt27
while using SPFlash Tool

What I do:
Launch bypass.bat
Plug my phone with vol - pressed and battery unplugged.

[2021-08-24 21:33:09.958798] Waiting for device [2021-08-24 21:39:08.793257] Found device = 0e8d:0003 [2021-08-24 21:39:14.833772] Device hw code: 0x707 [2021-08-24 21:39:14.833772] Device hw sub code: 0x8a00 [2021-08-24 21:39:14.833772] Device hw version: 0xca00 [2021-08-24 21:39:14.833772] Device sw version: 0x0 [2021-08-24 21:39:14.833772] Device secure boot: True [2021-08-24 21:39:14.833772] Device serial link authorization: True [2021-08-24 21:39:14.833772] Device download agent authorization: True [2021-08-24 21:39:14.833772] Disabling watchdog timer [2021-08-24 21:39:14.849712] Disabling protection [2021-08-24 21:39:14.849712] Using kamakiri [2021-08-24 21:39:14.849712] Protection disabled Appuyez sur une touche pour continuer...

Then I use SPFlash Tool v5.1924.0
Tried with DA_6765_6785_6768_6873_6885_6853.bin and MTK_AllInOne_DA.bin


View attachment 5392951

What am I doing wrong?
or install mtk drivers properly
 

hckbkl

Senior Member
Jun 12, 2021
89
7
76
Xiaomi Black Shark 4
Hello and thanks for sharing, I have the same error as @willkurt27
while using SPFlash Tool

What I do:
Launch bypass.bat
Plug my phone with vol - pressed and battery unplugged.

[2021-08-24 21:33:09.958798] Waiting for device [2021-08-24 21:39:08.793257] Found device = 0e8d:0003 [2021-08-24 21:39:14.833772] Device hw code: 0x707 [2021-08-24 21:39:14.833772] Device hw sub code: 0x8a00 [2021-08-24 21:39:14.833772] Device hw version: 0xca00 [2021-08-24 21:39:14.833772] Device sw version: 0x0 [2021-08-24 21:39:14.833772] Device secure boot: True [2021-08-24 21:39:14.833772] Device serial link authorization: True [2021-08-24 21:39:14.833772] Device download agent authorization: True [2021-08-24 21:39:14.833772] Disabling watchdog timer [2021-08-24 21:39:14.849712] Disabling protection [2021-08-24 21:39:14.849712] Using kamakiri [2021-08-24 21:39:14.849712] Protection disabled Appuyez sur une touche pour continuer...

Then I use SPFlash Tool v5.1924.0
Tried with DA_6765_6785_6768_6873_6885_6853.bin and MTK_AllInOne_DA.bin


View attachment 5392951

What am I doing wrong?
use mtkbypass
 

Top Liked Posts

  • There are no posts matching your filters.
  • 1
    Already using VDV171 MTK Bypass

    I can flash some Roms without problems like:
    lancelot_global_images_V12.0.1.0.RJCMIXM_20210609.0000.00_11.0_global
    lancelot_global_images_V11.0.8.0.QJCMIXM_20200905.0000.00_10.0_global

    I can't flash:
    lancelot_global_images_V11.0.4.0.QJCMIXM_20200618.0000.00_10.0_global
    LANCELOT_Engineering_AL2615-lancelot-V011-Q-0623_QP1A.190711.020_by-VD171
    just grab the md1img from rom_eng.
    use that md1img in romglobal.
    can also flash md1img separately or just flash md1img rom_eng
  • 4
    after further testing and finally restoring my IMEIs using this rom, i can say that it is indeed working, so hope it helps a lot of you guys stuck with a phone without IMEIs.
    link :

    Requirements:
    - SP flash tool and right DA file (provided in the post).
    -brom bypass (also provided).
    -patience and perseverance.

    Steps to install:
    1)steps to install brom bypass:
    -first install python 3 (check on google)
    - then run this code in a cmd
    Code:
    pip install pyusb pyserial json5
    -after that make sure to have all the mediatek drivers installed and install libusb from the archive i provided
    - after installing libusb you will be greeted by a filter wizard window, check the "install new device filter" then connect the phone to the pc while pressing (volume +, volume - and power button) all at the same time you
    will see in the list a new mtk com port appear click on it and then on install, done with the prep'.
    2)steps to flash:
    -first launch the brom bypass, a window will appear saying 'waiting for bootrom' connect your phone while pressing (volume +, volume - and power button) all together then you will see on the command prompt 'protection disabled' it means you have successfully bypassed the brom.
    - now oppen up sp flash tool, select the download agent, select the scatter fille from the rom folder and the auth file (provided with sp flash tool archive on the post) then setup sp flash tool in uart mode with a bud rate of 921600 then flash in format all.
    -done.

    Hope this helped, cheers !
    1
    Already using VDV171 MTK Bypass

    I can flash some Roms without problems like:
    lancelot_global_images_V12.0.1.0.RJCMIXM_20210609.0000.00_11.0_global
    lancelot_global_images_V11.0.8.0.QJCMIXM_20200905.0000.00_10.0_global

    I can't flash:
    lancelot_global_images_V11.0.4.0.QJCMIXM_20200618.0000.00_10.0_global
    LANCELOT_Engineering_AL2615-lancelot-V011-Q-0623_QP1A.190711.020_by-VD171
    just grab the md1img from rom_eng.
    use that md1img in romglobal.
    can also flash md1img separately or just flash md1img rom_eng