[TUTORIAL][ROMS] SP Tool Flashing Procedure

Search This thread
By:
Advanced…
Sam Solomon

Sam Solomon

Senior Member
Dec 7, 2012
1,400
2,600
25
Quilon
www.buzzeee.com
SP Tool Tutorial & SP Tool Flashable ROMs

DOWNLOADS


FLASHING ROM

1)Install Drivers.

2)Open SP tool
1.JPG

3)Select 'Android Scatter file' inside ROM folder.

2.JPG

4)Now Shut_Down Canvas 2.

5)Click Firmware_Upgrade Button.

3.JPG

6)Connect Phone{Switched off} to PC via USB Cable.

7)If everythings right,Flashing will proceed..

8)Wait till It finishes..A green ring is displayed on completion..

9)Now Close SP tool..Remove Phone from PC..

10)Switch ON the phone...It is successfully Flashed...


FLASHING PATCH(Single Files)

1)Select Android Scatter File .txt ....

2)Uncheck all files from the below box....

3)Select the correct file you want Flash by clicking it....

4)Click Download button on SP tool.... **"Dont click Firmware Upgrade"

5)A box asks to confirm it...Click Yes...

6)Connect Phone in Switch off State...

7)It will get Flashed...

HIT THANKS PLEASE BECAUSE IT WONT COST ANY :angel:


META-MODE

Meta-Mode is very useful if device fails to get detected by PC under normal Conditions.....To make device fall to Meta-Mode,just do these :

1) Start SP Tool on PC..
2) Now run SP Tool with "Firmware Upgrade/Download"
3) Switch OFF Phone..
4) Remove Battery..
5) Connect mobile to PC while holding Volume + button [WITHOUT BATTERY]..
6) Flashing will be started
7) Hold the button till flashing completes...
8) After 100% Flash,Release Button..
9) Insert Battery..
10) Start Device.. :good:



Note:I am not responsible for Mistakes and Bricked Devices...And dont flash ROM that arent made for A110 unless confirmed by others...​
 
Last edited:
  • Like
Reactions: ekss, UDIT.PATEL2526, Skqnder TN and 70 others
coolpartha

coolpartha

Senior Member
Feb 24, 2012
474
65
Re: [Tutorial]Flashing ROM via SP tool

will it get bak to our warranty?

Sent from my Samsung GT-S9081 using xda app-developers app
 
Sam Solomon

Sam Solomon

Senior Member
Dec 7, 2012
1,400
2,600
25
Quilon
www.buzzeee.com
Re: [Tutorial]Flashing ROM via SP tool

coolpartha said:
hnw to flash??? is thr ny jb stock rom?

Sent from my Samsung GT-S9081 using xda app-developers app
Click to expand...

No,For getting Warranty you have to flash only Micromax Official Stock ROM.....JB ROMs are there but you will loose warranty..:rolleyes:

Sent from my Micromax A110 Canvas 2 using xda premium
 
  • Like
Reactions: saurabhsn, dvl2dhaval, The_GMAN and 1 other person
T

tanmay5

Senior Member
May 10, 2012
88
21
Jammu
unable to root using your method help
when i clicked on firmware->upgrade it said check weather all images are loaded properly i pressed ok.
i tried to install super pro update but it says installation aborted but doesnt help it always strucks at 0% doesnt move forward no green ring as i only selected recovery and browsed for it on local drive.
i m struck on stock recovery requires cwm becuz i require pre rooted rom help..........
 
  • Like
Reactions: NeMann
Sam Solomon

Sam Solomon

Senior Member
Dec 7, 2012
1,400
2,600
25
Quilon
www.buzzeee.com
Re: [Tutorial]Flashing ROM via SP tool

tanmay5 said:
unable to root using your method help
when i clicked on firmware->upgrade it said check weather all images are loaded properly i pressed ok.
i tried to install super pro update but it says installation aborted but doesnt help it always strucks at 0% doesnt move forward no green ring as i only selected recovery and browsed for it on local drive.
i m struck on stock recovery requires cwm becuz i require pre rooted rom help..........
Click to expand...

If you want yo install recovery alone then click Download instead of Firmware upgrade

Sent from my ZP950 using xda premium
 
  • Like
Reactions: sereshkhk
T

tanmay5

Senior Member
May 10, 2012
88
21
Jammu
i only selected recovery and pressed download then warning message pompt up that

"not all images are properly loaded you still want to continue i pressed ok"

my phone is switched of and then i connected to pc and nothing working on sptool/flash tool
it strucks on 0% and no green ring on sptools

Help me plzzz........

drivers to cynus t2 rom are installed on my pc n can b traced under device manager if debuggging n media is on help......
 
Sam Solomon

Sam Solomon

Senior Member
Dec 7, 2012
1,400
2,600
25
Quilon
www.buzzeee.com
Re: [Tutorial]Flashing ROM via SP tool

tanmay5 said:
i only selected recovery and pressed download then warning message pompt up that

"not all images are properly loaded you still want to continue i pressed ok"

my phone is switched of and then i connected to pc and nothing working on sptool/flash tool
it strucks on 0% and no green ring on sptools

Help me plzzz........

drivers to cynus t2 rom are installed on my pc n can b traced under device manager if debuggging n media is on help......
Click to expand...

Not Debugging drivers...Preloader drivers have to be installed

Sent from my ZP950 using xda premium
 
  • Like
Reactions: sereshkhk and tanmay5
T

tanmay5

Senior Member
May 10, 2012
88
21
Jammu
yeah my mt65xx drivers was not installed after installing/updating from drive i selected mobile cynus t2 under program files and said encounted a problem and cant update drivers so i downloaded MT65xx drivers from xda site and browsed and drivers got installed named is preloade usb vcom(android) Com 4. i used sp flash tools selected scatter file n recovery pressed download

red bar completes 100% and showing enter usb in 15 sec after that i get an error helpp.............

error 8100 cant find usb port

what should i do know
 
Sam Solomon

Sam Solomon

Senior Member
Dec 7, 2012
1,400
2,600
25
Quilon
www.buzzeee.com
Re: [Tutorial]Flashing ROM via SP tool

tanmay5 said:
yeah my mt65xx drivers was not installed after installing/updating from drive i selected mobile cynus t2 under program files and said encounted a problem and cant update drivers so i downloaded MT65xx drivers from xda site and browsed and drivers got installed named is preloade usb vcom(android) Com 4. i used sp flash tools selected scatter file n recovery pressed download

red bar completes 100% and showing enter usb in 15 sec after that i get an error helpp.............

error 8100 cant find usb port

what should i do know
Click to expand...

Try other USB port...

Sent from my Micromax™ A110 using xda premium
 
  • Like
Reactions: sereshkhk
drsooraj

drsooraj

Senior Member
Dec 8, 2012
380
93
Thrissur
Re: [Tutorial]Flashing ROM via SP tool

Y dont u use other simpler rooting tools available.. And install cwm via mobileuncle tools.. So u can skip the spflash tool method altogather

Sent from my Micromax A110
 
drsooraj

drsooraj

Senior Member
Dec 8, 2012
380
93
Thrissur
Re: [Tutorial]Flashing ROM via SP tool

That error is due to failed vcom drivers itself. U need more trial and errors..like pdanet drivers..few Windows restarts.. Well how did u get jb Rom in the first place? Stock jb over stock recovery?
Can you somehow revert to ics again?
Sent from my Micromax A110
 
You must log in or register to reply here.

Similar threads

P
[Q] My Micromax A110 is Dead while flashing stock ROM through SP tool
Replies
1
Views
752
rkmadotra
rkmadotra
S
[Q] Can't flash by sp tool
Replies
1
Views
607
jatin@1
[email protected]
Rana Fahad Khan
[Flash Tool] SP Flash Tool Latest - v 3.13
Replies
2
Views
21K
F
furiouskid
C
[Update] SP Tool flash JB v1.11 Stock Micromax Official
Replies
19
Views
24K
@
@bunty
A
not responding to sp flash tool
Replies
8
Views
17K
K
kbheda

Top Liked Posts

24 Hours All time
  • There are no posts matching your filters.
  • 73
    Sam Solomon
    Sam Solomon
    SP Tool Tutorial & SP Tool Flashable ROMs

    DOWNLOADS


    FLASHING ROM

    1)Install Drivers.

    2)Open SP tool
    1.JPG

    3)Select 'Android Scatter file' inside ROM folder.

    2.JPG

    4)Now Shut_Down Canvas 2.

    5)Click Firmware_Upgrade Button.

    3.JPG

    6)Connect Phone{Switched off} to PC via USB Cable.

    7)If everythings right,Flashing will proceed..

    8)Wait till It finishes..A green ring is displayed on completion..

    9)Now Close SP tool..Remove Phone from PC..

    10)Switch ON the phone...It is successfully Flashed...


    FLASHING PATCH(Single Files)

    1)Select Android Scatter File .txt ....

    2)Uncheck all files from the below box....

    3)Select the correct file you want Flash by clicking it....

    4)Click Download button on SP tool.... **"Dont click Firmware Upgrade"

    5)A box asks to confirm it...Click Yes...

    6)Connect Phone in Switch off State...

    7)It will get Flashed...

    HIT THANKS PLEASE BECAUSE IT WONT COST ANY :angel:


    META-MODE

    Meta-Mode is very useful if device fails to get detected by PC under normal Conditions.....To make device fall to Meta-Mode,just do these :

    1) Start SP Tool on PC..
    2) Now run SP Tool with "Firmware Upgrade/Download"
    3) Switch OFF Phone..
    4) Remove Battery..
    5) Connect mobile to PC while holding Volume + button [WITHOUT BATTERY]..
    6) Flashing will be started
    7) Hold the button till flashing completes...
    8) After 100% Flash,Release Button..
    9) Insert Battery..
    10) Start Device..     :good:



    Note:I am not responsible for Mistakes and Bricked Devices...And dont flash ROM that arent made for A110 unless confirmed by others...​
    View
    4
    Sam Solomon
    Sam Solomon
    Re: [Tutorial]Flashing ROM via SP tool

    coolpartha said:
    hnw to flash??? is thr ny jb stock rom?

    Sent from my Samsung GT-S9081 using xda app-developers app
    Click to expand...

    No,For getting Warranty you have to flash only Micromax Official Stock ROM.....JB ROMs are there but you will loose warranty..:rolleyes:

    Sent from my Micromax A110 Canvas 2 using xda premium
    View
    3
    lopestom
    lopestom
    Re: [Tutorial]Flashing ROM via SP tool

    You have a right click (picture 1) property/settings and change driver in you PC of the phone.

    example: MediaTek DA USB VCOM driver for MT6577
    After install automaticly ADB drives.
    After this a yellow symbol go out.

    Sent from my VIVO 4.3 using xda app-developers app
    -------------------------------------------------------------------------------
    Hey guys,
    Sorry if I'm interrupting. But I've used SP Flash and flash many ROM's for my device. I not have your device, but only that the process is always the same.
    However, I ask Dark4Droid: Why do the "5) Click Firmware_Upgrade Button"?
    I ask this because I did not have to perform this action/option.

    Many users SP Flash not know, as I had to learn that the driver must update the phone again. View this ..... http://forum.xda-developers.com/showthread.php?t=1982587
    Some have SP Flash folder containing drivers (InstallDriver.exe), but also need to reinstall the driver folder ADB (android_winusb.inf).
    View
    3
    T
    tanmay5
    Dude you are life saver

    By enabling UAC n by disabling Driver signature in Win 8

    Some how i was unable to download the recover.img flash tool was giving an error

    But by firmware-upgrade my phone got updated to official Ics state n later i downloaded recovery.img

    thanx a ton bro....

    going to install Jelly dream rom by dark4droid

    thanx all spply dark4droid n lopestom thanx a lot
    View
    2
    Sam Solomon
    Sam Solomon
    Re: [Tutorial]Flashing ROM via SP tool

    tanmay5 said:
    i only selected recovery and pressed download then warning message pompt up that

    "not all images are properly loaded you still want to continue i pressed ok"

    my phone is switched of and then i connected to pc and nothing working on sptool/flash tool
    it strucks on 0% and no green ring on sptools

    Help me plzzz........

    drivers to cynus t2 rom are installed on my pc n can b traced under device manager if debuggging n media is on help......
    Click to expand...

    Not Debugging drivers...Preloader drivers have to be installed

    Sent from my ZP950 using xda premium
    View

New posts

Our Apps
Get our official app!
The best way to access XDA on your phone
Nav Gestures
Add swipe gestures to any Android
One Handed Mode
Eases uses one hand with your phone