[UNBRICK Guide][for Bootloader v1 jb only][I9195]How to unbrick your device

Search This thread

Aronuser

Senior Member
Mar 1, 2014
1,049
442
Berlin
Disclaimer:

I'm not liable to any demage to your device, including Knox. The information here is as good as I know, there is no guarantee.


(If you like to provide extra information or have a correction, I'll add it to the OP)


>>I'm searching for more full repair firmwares (Containing, PIT, Bootloader, etc. seperated), if anyone could send me the files for I9195 and I9192 etc. i'd upload them too, please help and help others.<<


There are several types of a brick:

Bootloop (usually possible to unbrick)

Stuck at splash screen (a bit harder but still usually possible)

Hardbrick (black screen and nothing works) (there is also a possible solution but it could also mean the end)

Full brick (black screen, nothing works, even the hardbrick method doesn't work. solution could be using a JTAG)

How to unbrick a bootloop and stuck at splash screen brick

Download one of the repair firmwares from here

I9195 Here

Thanks a lot for providing the I9195 files to: @b0g

PIT file:
https://drive.google.com/file/d/0Bx2R0nz6jh17bllKenctWnVsWkE/edit?usp=sharing

Other files:
https://drive.google.com/file/d/0Bx2R0nz6jh17aEVHMHkwLVRjWVE/edit?usp=sharing

###########################################################################################

- Unzip/unrar the files

- Install usb drivers and use the Odin program

- Put the files like the following:

(file names starting with: )
Bootloader (BL) > BOOTLOADER...
PDA (AP) > CODE...
PHONE (CP) > MODEM...
CSC > CSC...
PIT > CSB...

- Make sure your device has enough charge 40% is recommended

- Enter download mode (press volume down + home + power button in the booting process for around 20 seconds)

- connect your device (Odin should say "Added")

- Click start (do NOT disconnect your device or restart your computer in the flashing process, this could make things worse)

- Wait until the phone has fully reset and enter the recovery

- Do a "Factory reset" and "Wipe cache"

- Reboot

- Done

How to unbrick a Hardbricked phone

- Buy a USB-JIG online

- Make sure that the devices battery has charged (even if it doesn't show charging animation)

- Remove your battery

- Plug the USB-JIG inside your phone

- Wait 3 minutes and put the battery back inside

- Wait 40 seconds and the "download mode" screen should appear

- Follow the steps like in the "Bootloop and stuck at splashscreen guide" as above (note: you don't have to enter download mode because using the JIG it should enter it automatically)

Credits:
Me
@b0g
 
Last edited:

skortax

New member
Jun 17, 2014
2
1
hi.

i search a solution repair my s4 mini for hours. tried many ways on this forum and others, but nothing works. so i found this and use the data follow the steps above to ressurrect my phone of bootloop and stuck.
odin flashs correctly i think, but after the reset the phone stucks in "recovery booting..."

i checked autoreboot and re partitition, unchecked f reset time. the odin log says everthing ok:

<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9195XXUBML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9195XXUBML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9195XXUBML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_OXA_I9195OXABML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> aboot.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sbl1.mbn
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> aboot.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> persist.img.ext4
<ID:0/003> persdata.img.ext4
<ID:0/003> NON-HLOS.bin
<ID:0/003> Transmission Complete..
<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003> Receive Response from boot-loader
<ID:0/003> cache.img.ext4
<ID:0/003> hidden.img.ext4
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/003> Removed!!

what can i do, please help?
 
  • Like
Reactions: cyby

Aronuser

Senior Member
Mar 1, 2014
1,049
442
Berlin
hi.

i search a solution repair my s4 mini for hours. tried many ways on this forum and others, but nothing works. so i found this and use the data follow the steps above to ressurrect my phone of bootloop and stuck.
odin flashs correctly i think, but after the reset the phone stucks in "recovery booting..."

i checked autoreboot and re partitition, unchecked f reset time. the odin log says everthing ok:

<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9195XXUBML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9195XXUBML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9195XXUBML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_OXA_I9195OXABML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> aboot.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sbl1.mbn
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> aboot.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> persist.img.ext4
<ID:0/003> persdata.img.ext4
<ID:0/003> NON-HLOS.bin
<ID:0/003> Transmission Complete..
<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003> Receive Response from boot-loader
<ID:0/003> cache.img.ext4
<ID:0/003> hidden.img.ext4
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/003> Removed!!

what can i do, please help?

try flashing twrp recovery and wipe all then (despite external sd)

also try flashing with f reset time enabled...
 

skortax

New member
Jun 17, 2014
2
1
thanks for the quick help. flashed twrp and it boots in recovery, but full wipe doesnt run, so i wiped manually - unfortunately i get bluescreen and i am again at the beginning.

every method i tried ends with the same result: bluescreen, blackscreen, greenscreen and every other existing screen, in every possible loop or odin stuck during the flash process :(

i think the problem lies deeper and can only be solved with jtag, if it is not an hardware error. what do you think?
 
Last edited:

woggle

Member
Jun 8, 2007
29
3
Hi I'm having a similar issue with my i9195 getting stuck on boot screen. I think mine has something todo with the new battery i got for it, as the new one only has 3 pins and the old has 4?

one way i found of being able to boot my phone was to take out the battery plug the charger in then put the battery back in once the green battery icon shows that it is charging hold the power until it vibrates and it should (it does for me) start up, i was also able to get into recovery using the above method by holding the home and volume up as normal.
 
  • Like
Reactions: Aronuser

Loulou-13

Senior Member
Aug 24, 2013
1,826
666
Marseille
....

I9195 Here

Thanks a lot for providing the I9195 files to: @b0g

PIT file:
https://drive.google.com/file/d/0Bx2R0nz6jh17bllKenctWnVsWkE/edit?usp=sharing

Other files:
https://drive.google.com/file/d/0Bx2R0nz6jh17aEVHMHkwLVRjWVE/edit?usp=sharing

###########################################################################################

- Unzip/unrar the files

- Install usb drivers and use the Odin program

- Put the files like the following:

(file names starting with: )
Bootloader (BL) > BOOTLOADER...
PDA (AP) > CODE...
PHONE (CP) > MODEM...
CSC > CSC...
PIT > CSB...

- Make sure your device has enough charge 40% is recommended

- Enter download mode (press volume down + home + power button in the booting process for around 20 seconds)

- connect your device (Odin should say "Added")

- Click start (do NOT disconnect your device or restart your computer in the flashing process, this could make things worse)

- Wait until the phone has fully reset and enter the recovery

- Do a "Factory reset" and "Wipe cache"

- Reboot

- Done

.....


hi !

can i use this part for to try to downgrade a KK firmware to JB ???!!!

have to check "re-partition" ???
 

Loulou-13

Senior Member
Aug 24, 2013
1,826
666
Marseille
yes ,i think i will try it , but i'm "nervious" with re-partition and pit ! i'm a little afraid ...
i would have prefered an advise to a person"spécialist" who know Samsung very well ...... before testing with this flash .

but i know "re-partition" and Odin (I have already had olds Samsungs )

it's principaly the **** of **** of ****** of HELL "Knox" who scares me ... :(

The pit here is REALLY the good ???


There are devises who have good(s) method(s) for to downgrade , there are other that it's really impossible ..... but for the S4-mini ,nobody have done expérimenations about ,no tutorials ...etc ...
everybody flash as one file .tar now ...

EDIT !

maybe the master @arco68 can answer to this problem ???!!!
 
Last edited:

jerrry

Senior Member
May 18, 2006
126
5
Prague
Hello, can you please help me? I have problems with random restarting of my i9195 S4 Mini (Vodafone). I tried to flash another official ROM, but this problem remains. When I try flash back original stock ROM (or any other ROM - with root or without root), the results are still same - FAIL message in ODIN after aboot.mbn file.

I tried this guide, but again, everything was ended with fail message (check the attached log).

Code:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9195XXUBML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9195XXUBML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9195XXUBML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_OXA_I9195OXABML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sbl1.mbn
<ID:0/004> NAND Write Start!! 
<ID:0/004> sbl2.mbn
<ID:0/004> sbl3.mbn
<ID:0/004> aboot.mbn
<ID:0/004> FAIL! (Auth)
<ID:0/004> 
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Can you please help me and tell me what I can do if I want to put back any stock ROM? I am going crazy with the fail message which shows me in every try. Checked with Odin 3.09, 3.07, 1.83 and still no success.
 

sasank360

Senior Member
Feb 27, 2012
692
329
Hyderabad
Hello, can you please help me? I have problems with random restarting of my i9195 S4 Mini (Vodafone). I tried to flash another official ROM, but this problem remains. When I try flash back original stock ROM (or any other ROM - with root or without root), the results are still same - FAIL message in ODIN after aboot.mbn file.

Can you please help me and tell me what I can do if I want to put back any stock ROM? I am going crazy with the fail message which shows me in every try. Checked with Odin 3.09, 3.07, 1.83 and still no success.

Can you tell what is the text in download mode screen? If the last 2 lines say BOOTLOADER SW REV : 2, then you have latest bootloader and IT IS IMPOSSIBLE TO DOWNGRADE. :(
 

jerrry

Senior Member
May 18, 2006
126
5
Prague
Can you tell what is the text in download mode screen? If the last 2 lines say BOOTLOADER SW REV : 2, then you have latest bootloader and IT IS IMPOSSIBLE TO DOWNGRADE. :(

Thank you for reply. Yes, I have Bootloader AP SWREV: 2. But what can I do if I want to change actual ROM which is flashed in device? I would like to get back original Vodafone ROM (stock), but I can't do anything (flash same ROM which is now in device, flash Vodafone ROM, flash custom ROM).
 

j0ep0

Senior Member
Jul 12, 2010
308
406
Utrecht
Hello, can you please help me? I have problems with random restarting of my i9195 S4 Mini (Vodafone). I tried to flash another official ROM, but this problem remains. When I try flash back original stock ROM (or any other ROM - with root or without root), the results are still same - FAIL message in ODIN after aboot.mbn file.

I tried this guide, but again, everything was ended with fail message (check the attached log).

Code:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9195XXUBML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9195XXUBML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9195XXUBML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_OXA_I9195OXABML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sbl1.mbn
<ID:0/004> NAND Write Start!! 
<ID:0/004> sbl2.mbn
<ID:0/004> sbl3.mbn
<ID:0/004> aboot.mbn
<ID:0/004> FAIL! (Auth)
<ID:0/004> 
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Can you please help me and tell me what I can do if I want to put back any stock ROM? I am going crazy with the fail message which shows me in every try. Checked with Odin 3.09, 3.07, 1.83 and still no success.

I had the same issue (aboot.mbn failing and finally I managed to fix it by flashing I9195XXUCNE6_I9195OXACNE6_DBT with Odin 3.09. Downloaded the firmware from sammobile (http://www.sammobile.com/firmwares/3/?confirm=31540). Had to wipe data/cache after flashing the ROM. Not the ROM I wanted, but at least now I have a working S4 mini again.
 

Aronuser

Senior Member
Mar 1, 2014
1,049
442
Berlin
Thank you for reply. Yes, I have Bootloader AP SWREV: 2. But what can I do if I want to change actual ROM which is flashed in device? I would like to get back original Vodafone ROM (stock), but I can't do anything (flash same ROM which is now in device, flash Vodafone ROM, flash custom ROM).

skip the modem file and the bootloader file at flashing and you should be fine
 

Top Liked Posts

  • There are no posts matching your filters.
  • 32
    Disclaimer:

    I'm not liable to any demage to your device, including Knox. The information here is as good as I know, there is no guarantee.


    (If you like to provide extra information or have a correction, I'll add it to the OP)


    >>I'm searching for more full repair firmwares (Containing, PIT, Bootloader, etc. seperated), if anyone could send me the files for I9195 and I9192 etc. i'd upload them too, please help and help others.<<


    There are several types of a brick:

    Bootloop (usually possible to unbrick)

    Stuck at splash screen (a bit harder but still usually possible)

    Hardbrick (black screen and nothing works) (there is also a possible solution but it could also mean the end)

    Full brick (black screen, nothing works, even the hardbrick method doesn't work. solution could be using a JTAG)

    How to unbrick a bootloop and stuck at splash screen brick

    Download one of the repair firmwares from here

    I9195 Here

    Thanks a lot for providing the I9195 files to: @b0g

    PIT file:
    https://drive.google.com/file/d/0Bx2R0nz6jh17bllKenctWnVsWkE/edit?usp=sharing

    Other files:
    https://drive.google.com/file/d/0Bx2R0nz6jh17aEVHMHkwLVRjWVE/edit?usp=sharing

    ###########################################################################################

    - Unzip/unrar the files

    - Install usb drivers and use the Odin program

    - Put the files like the following:

    (file names starting with: )
    Bootloader (BL) > BOOTLOADER...
    PDA (AP) > CODE...
    PHONE (CP) > MODEM...
    CSC > CSC...
    PIT > CSB...

    - Make sure your device has enough charge 40% is recommended

    - Enter download mode (press volume down + home + power button in the booting process for around 20 seconds)

    - connect your device (Odin should say "Added")

    - Click start (do NOT disconnect your device or restart your computer in the flashing process, this could make things worse)

    - Wait until the phone has fully reset and enter the recovery

    - Do a "Factory reset" and "Wipe cache"

    - Reboot

    - Done

    How to unbrick a Hardbricked phone

    - Buy a USB-JIG online

    - Make sure that the devices battery has charged (even if it doesn't show charging animation)

    - Remove your battery

    - Plug the USB-JIG inside your phone

    - Wait 3 minutes and put the battery back inside

    - Wait 40 seconds and the "download mode" screen should appear

    - Follow the steps like in the "Bootloop and stuck at splashscreen guide" as above (note: you don't have to enter download mode because using the JIG it should enter it automatically)

    Credits:
    Me
    @b0g
    3
    I9195 mirror at Google drive added

    Huge thanks go to @b0g for providing the files for I9195! :good:
    2
    hi.

    i search a solution repair my s4 mini for hours. tried many ways on this forum and others, but nothing works. so i found this and use the data follow the steps above to ressurrect my phone of bootloop and stuck.
    odin flashs correctly i think, but after the reset the phone stucks in "recovery booting..."

    i checked autoreboot and re partitition, unchecked f reset time. the odin log says everthing ok:

    <OSM> Enter CS for MD5..
    <OSM> Check MD5.. Do not unplug the cable..
    <OSM> Please wait..
    <OSM> BOOTLOADER_I9195XXUBML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
    <OSM> Checking MD5 finished Sucessfully..
    <OSM> Leave CS..
    <OSM> Enter CS for MD5..
    <OSM> Check MD5.. Do not unplug the cable..
    <OSM> Please wait..
    <OSM> CODE_I9195XXUBML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
    <OSM> Checking MD5 finished Sucessfully..
    <OSM> Leave CS..
    <OSM> Enter CS for MD5..
    <OSM> Check MD5.. Do not unplug the cable..
    <OSM> Please wait..
    <OSM> MODEM_I9195XXUBML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
    <OSM> Checking MD5 finished Sucessfully..
    <OSM> Leave CS..
    <OSM> Enter CS for MD5..
    <OSM> Check MD5.. Do not unplug the cable..
    <OSM> Please wait..
    <OSM> CSC_OXA_I9195OXABML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
    <OSM> Checking MD5 finished Sucessfully..
    <OSM> Leave CS..
    <ID:0/003> Added!!
    <ID:0/003> Odin v.3 engine (ID:3)..
    <ID:0/003> File analysis..
    <ID:0/003> SetupConnection..
    <ID:0/003> Initialzation..
    <ID:0/003> Set PIT file..
    <ID:0/003> DO NOT TURN OFF TARGET!!
    <ID:0/003> Get PIT for mapping..
    <ID:0/003> Firmware update start..
    <ID:0/003> SingleDownload.
    <ID:0/003> sbl1.mbn
    <ID:0/003> NAND Write Start!!
    <ID:0/003> sbl2.mbn
    <ID:0/003> sbl3.mbn
    <ID:0/003> aboot.mbn
    <ID:0/003> rpm.mbn
    <ID:0/003> tz.mbn
    <ID:0/003> sbl1.mbn
    <ID:0/003> sbl2.mbn
    <ID:0/003> sbl3.mbn
    <ID:0/003> aboot.mbn
    <ID:0/003> rpm.mbn
    <ID:0/003> tz.mbn
    <ID:0/003> boot.img
    <ID:0/003> recovery.img
    <ID:0/003> system.img.ext4
    <ID:0/003> persist.img.ext4
    <ID:0/003> persdata.img.ext4
    <ID:0/003> NON-HLOS.bin
    <ID:0/003> Transmission Complete..
    <ID:0/003> Now Writing.. Please wait about 2 minutes
    <ID:0/003> Receive Response from boot-loader
    <ID:0/003> cache.img.ext4
    <ID:0/003> hidden.img.ext4
    <ID:0/003> RQT_CLOSE !!
    <ID:0/003> RES OK !!
    <ID:0/003> Remain Port .... 0
    <OSM> All threads completed. (succeed 1 / failed 0)
    <ID:0/003> Removed!!

    what can i do, please help?

    try flashing twrp recovery and wipe all then (despite external sd)

    also try flashing with f reset time enabled...
Our Apps
Get our official app!
The best way to access XDA on your phone
Nav Gestures
Add swipe gestures to any Android
One Handed Mode
Eases uses one hand with your phone