Question Xiaomi Note 11 stuck to rebooting into recovery mode 5.0 after unlocking the screen

[Tryskacz]

hello all, and thx for all advices in this thread
i managed to fix boot to recovery loop with uninstalling com.qualcomm.location

it was pain to turn on usb debugging so i will share my experience
heating up unfortunately didn't help

i tried it with sim, without sim, with sd card, without sd card
i noticed system is laggy with sd card - even the settings did not open

so i just poped the slot 2mm out, only sd card in - restarted - unlocked phone -> opened settings -> dev settings -> poped card socket in - and turn on the usb debugging

somehow this gave me more time to confirm it

ps: locksreen with no pin code makes phone auto reboot without touching it, 1st i did the card trick to set the locksreen pincode

maybe this help someone else

thx again xda people

 

[ekrumova]

Go to Settings -> System Apps Updater (Below About my phone) -> 3 dots on top right -> Settings -> Disable automatic updates

i just disable only installing automatic updates but enable downloading automatic updates

 

[sohel yadav]

with this optin my data not to be lost ?

data wont lost

 

[NeedToRepair]

hello all, and thx for all advices in this thread
i managed to fix boot to recovery loop with uninstalling com.qualcomm.location

it was pain to turn on usb debugging so i will share my experience
heating up unfortunately didn't help

i tried it with sim, without sim, with sd card, without sd card
i noticed system is laggy with sd card - even the settings did not open

so i just poped the slot 2mm out, only sd card in - restarted - unlocked phone -> opened settings -> dev settings -> poped card socket in - and turn on the usb debugging

somehow this gave me more time to confirm it

ps: locksreen with no pin code makes phone auto reboot without touching it, 1st i did the card trick to set the locksreen pincode

maybe this help someone else

thx again xda people

Im at this point, but it doesnt work for me...

 

[yannick7fr]

Hello everyone,

Just would like to thank you guys for the help I've found here ! (xiaomi's solution is to wipe everything .... )
The hardest part was to enable USB Debug.
First, getting the correct procedure for my phone, then doing it as fast as possible.
The idea of heating my phone to gain some time looks crazy but it actually work. I personally put my phone close to my wood stove to heat it up (not to close ! )
Finally, the adb part was easy (found some help using adb for linux here : Link )

Just dropping the procedure to enable USB Debug in case someone looks for it
Settings > Additional settings > Developer Options > USB Debug

Now my phone wants me to upgrade to MIUI 13.0.13.0. I'm currently running MIUI 13.0.12.0 (RGKEUXM).

What do you guys think ? Doing the upgrade or not ?
I have to admit, I'm a little fearful doing the upgrade after one day without a phone, struggling with debug mode.

 

[m0rt4r]

Actually I decided to do wipe tomorrow since not much time for reinstalling today and because of that I tried few more times with heating the phone. This time I used hair drier, put phone between bed sheet and heated it for like 1-2 min each side (previously I was doing it shorter, this time I tried for a bit longer). Finally it worked. Also I previously heated phone when it was on lock screen but this times I was heating phone while it was on the black "reboot screen" and did the restart after heating phone, finishing the heating after lock screen appeared.

Now I have problem with adb cause my device list is empty after using "adb devices" command but I will work with this tomorrow.

 

[polal31]

Bonjour à tous,

Je voudrais juste vous remercier pour l'aide que j'ai trouvée ici ! (la solution de xiaomi est de tout effacer.... )
Le plus difficile était d'activer le débogage USB.
Tout d'abord, obtenir la bonne procédure pour mon téléphone, puis le faire aussi vite que possible.
L'idée de chauffer mon téléphone pour gagner du temps semble folle mais ça marche vraiment. Personnellement, je mets mon téléphone près de mon poêle à bois pour le chauffer :RÉ (pas pour le fermer ! )
Enfin, la partie adb était facile (j'ai trouvé de l'aide pour utiliser adb pour linux ici : Lien )

Il suffit de laisser tomber la procédure pour activer le débogage USB au cas où quelqu'un le chercherait
Paramètres > Paramètres supplémentaires > Options pour les développeurs > Débogage USB

Maintenant, mon téléphone veut que je passe à MIUI 13.0.13.0. J'utilise actuellement MIUI 13.0.12.0 (RGKEUXM).

Qu'en pensez-vous ? Faire la mise à jour ou pas ?
Je dois admettre que j'ai un peu peur de faire la mise à niveau après une journée sans téléphone, aux prises avec le mode débogage.

Hello everyone,

Just would like to thank you guys for the help I've found here ! (xiaomi's solution is to wipe everything .... )
The hardest part was to enable USB Debug.
First, getting the correct procedure for my phone, then doing it as fast as possible.
The idea of heating my phone to gain some time looks crazy but it actually work. I personally put my phone close to my wood stove to heat it up (not to close ! )
Finally, the adb part was easy (found some help using adb for linux here : Link )

Just dropping the procedure to enable USB Debug in case someone looks for it
Settings > Additional settings > Developer Options > USB Debug

Now my phone wants me to upgrade to MIUI 13.0.13.0. I'm currently running MIUI 13.0.12.0 (RGKEUXM).

What do you guys think ? Doing the upgrade or not ?
I have to admit, I'm a little fearful doing the upgrade after one day without a phone, struggling with debug mode.

Hello
I have 13.0.13.0 and i have since yesterday the same problem... So this version isn't better.
Somenone have news from Xiaomi ??? i
I m fighting to save my phone datas... what a mess !!!!

 

[DeStROY_dA_WoRld]

Now my phone wants me to upgrade to MIUI 13.0.13.0. I'm currently running MIUI 13.0.12.0 (RGKEUXM).

What do you guys think ? Doing the upgrade or not ?
I have to admit, I'm a little fearful doing the upgrade after one day without a phone, struggling with debug mode.

Please bear in mind that, as it has been stated in previous posts, upgrading the system don't actually reinstall the buggy component. I have 13.0.13.0 and the bug occured to me so I had to proceed to the component removing via ADB.

Finally, the tricky part being enabling USB debug, even though your phone should enter into bootloop mode again after update, you'd only have to repeat the ADB process.

Also, 13.0.5.0 should remove the bug, allowing you to reinstall the (no longer) buggy component. Personally, I know I won't

 

[ekrumova]

Hello guys, I'm still trying to enable USB debugging.
I updated my phone to new vers.13.0, but I can not see something to be different.

I think that Xiaomi have to release update with Uninstall the previous vers.13.5 and after that release 13.0.

I don't know what to do...

What do you think?

 

[xstage]

Hi, sorry for the bad english. My Xiaomi Note 11 worked perfectly fine for months since I bought it, but last night I accidentally left it charging for the whole night and when I woke up, it suddenly rebooted to recovery mode. I rebooted it back to system, which reboots the phone as usual, then I unlocked the lockscreen, everything went perfectly normal, until it rebooted again to recovery mode. I tried rebooting again, but it rebooted again to recovery mode after I unlocked the lockscreen. I tried booting it to safemode, but it went the same way. However, when I leave the lockscreen unlocked, it doesn't reboot itself. I tried turning it off and rebooting it with the screen unlocked but it did nothing. Do you guys ever have the same problem? Is there any way to fix it without wiping the data? I have some banking apps and other data that would be difficult to recover if I were to wipe out the phone.

same with me, but I managed to solve it by wiping data and all my files are gone :hammer

 

[kishore_001]

Hi, sorry for the bad english. My Xiaomi Note 11 worked perfectly fine for months since I bought it, but last night I accidentally left it charging for the whole night and when I woke up, it suddenly rebooted to recovery mode. I rebooted it back to system, which reboots the phone as usual, then I unlocked the lockscreen, everything went perfectly normal, until it rebooted again to recovery mode. I tried rebooting again, but it rebooted again to recovery mode after I unlocked the lockscreen. I tried booting it to safemode, but it went the same way. However, when I leave the lockscreen unlocked, it doesn't reboot itself. I tried turning it off and rebooting it with the screen unlocked but it did nothing. Do you guys ever have the same problem? Is there any way to fix it without wiping the data? I have some banking apps and other data that would be difficult to recover if I were to wipe out the

(2022/11/13)
I hope you guys can understand what I am trying to say ,I'm not good in English

exact same problem brother it happened today for me my device also Xiaomi Note 11, while this happen I'm playing clash of clans suddenly exit from the game and my device starts to restart and loads the to recovery mode and I just select reboot my device rebooted but I unlock my phone after few seconds again the device restart and bring me into recovery mode until I unlock my phone its okay whenever I unlock it its reboots and enter to recovery mode, the time I unlock my device I saw Xiaomi built in apps not visible for example calculator app, note app....

I'm a student my notes , short notes all my studying stuff is in this phone I'm so upset while I'm doing my advanced Levels I used a broken Samsung J1 mobile after that I bought this phone for my studies and other stuff, I bought Xiaomi Note 11 on 2022 march it has been 8 months I think now I'm facing this issue I hope this issue can be fixed without my any data.
I have warranty for my device I contact the mobile shop where I bought it they said bring the device to them, I will let you guys know if they fix my device maybe I think its MIUI OS crash or something

I forgot to tell you something before this error came I got a software update but I didn't install it maybe the problem?

Hello guys I'm kishore today I went to Xiaomi service center and I saw people at there having the same problem they took my device and upgrade my android version to 12 and now its working hopefully I think this won't happen again..(my data is good didn't happened anything to them)

if you guys have warranty just go to official service center you problem will solved, if you don't have warranty please visit trust phone repair center...

 

[polal31]

Hello !
Since today my phone work perfectly !
I Say previously that my redmi 11 is on 13.0.13.0 and the bug was working...
Thank you to everyone for the help !!!!

 

[blurryclique]

hello all, and thx for all advices in this thread
i managed to fix boot to recovery loop with uninstalling com.qualcomm.location

it was pain to turn on usb debugging so i will share my experience
heating up unfortunately didn't help

i tried it with sim, without sim, with sd card, without sd card
i noticed system is laggy with sd card - even the settings did not open

so i just poped the slot 2mm out, only sd card in - restarted - unlocked phone -> opened settings -> dev settings -> poped card socket in - and turn on the usb debugging

somehow this gave me more time to confirm it

ps: locksreen with no pin code makes phone auto reboot without touching it, 1st i did the card trick to set the locksreen pincode

maybe this help someone else

thx again xda people

This worked, after I had been trying the heating up method for hours. THANK YOU SO MUCH!!

 

[baasit_grant]

yes

that is good i did the same too yesterday

 

[JustJack123]

Hello everyone , yesterday , a family members phone has recieved the same boot loop after updating , and they insisted to fix it without wiping the phone data , this thread is exactly what ive been looking for, there is one problem tho , for some reason , unlike how it is with most others i see here , the phone restarts almost immeadetly after it boots up , it takes around 3 seconds to turn back off , making it impossible to enable usb debugging.
Does anyone have any idea why it acts differently like that ?

 

[NeedToRepair]

Finally today i got it!

With an SD card in the phone and after a day with the phone powered on I have succeeded in enabling USB-Debugging.
After that, with the phone locked, I was able to execute the commands:

The phone is working now.
Now i updated to 13.0.13.0 and still ok.

One question:
What did we uninstall?

 

[DeStROY_dA_WoRld]

Finally today i got it!

With an SD card in the phone and after a day with the phone powered on I have succeeded in enabling USB-Debugging.
After that, with the phone locked, I was able to execute the commands:

View attachment 5761467
The phone is working now.
Now i updated to 13.0.13.0 and still ok.

One question:
What did we uninstall?

This: https://forum.xda-developers.com/t/...er-unlocking-the-screen.4515039/post-87701833

 

[m0rt4r]

Hello everyone , yesterday , a family members phone has recieved the same boot loop after updating , and they insisted to fix it without wiping the phone data , this thread is exactly what ive been looking for, there is one problem tho , for some reason , unlike how it is with most others i see here , the phone restarts almost immeadetly after it boots up , it takes around 3 seconds to turn back off , making it impossible to enable usb debugging.
Does anyone have any idea why it acts differently like that ?

Do you have screen lock enabled? From what I saw previously someone posted that without any lock device was restarting after turning on.

Actually I decided to do wipe tomorrow since not much time for reinstalling today and because of that I tried few more times with heating the phone. This time I used hair drier, put phone between bed sheet and heated it for like 1-2 min each side (previously I was doing it shorter, this time I tried for a bit longer). Finally it worked. Also I previously heated phone when it was on lock screen but this times I was heating phone while it was on the black "reboot screen" and did the restart after heating phone, finishing the heating after lock screen appeared.

Now I have problem with adb cause my device list is empty after using "adb devices" command but I will work with this tomorrow.

Ok, today I was able to work with this adb. I think my pc have some problem with usb ports/drivers and was not seeing the phone so I used the old laptop.
I'm not sure if this helps someone but I didn't know how to work with this debugging mode and my phone was unauthorized when I used adb devices command (at least it was seen this time, list was not empty like on pc). When the phone is connected to the computer you need to unclock it and accept the debugging, phone can reboot after but laptop was now able to work with it and then it is shown after using adb devices command. Then just go:
adb shell
pm uninstall -k --user 0 com.qualcomm.location

and after unlocking screen phone is not restarting anymore.
Thanks everyone for help

 

[yannick7fr]

For the record, I've sent an email to xiaomi support yesterday. Sorry it's french

Bonjour,
Nous faisons suite à votre e-mail reçu le 13 Novembre 2022.


Nous vous remercions pour l'intérêt que vous portez à la marque Xiaomi.
Nous vous informons que la réinitialisation est le seul moyen pour régler le soucis rencontrer si cela ne fonctionne pas, le téléphone nécessitera une réparation.



Nous restons à votre disposition pour plus d'informations et nous vous remercions de nous avoir contacté.

Cordialement,
L'équipe Xiaomi France.

Basically, for them no way to fix this unless you wipe everything out ..... and if it's not working your phone will require a fix....
Finally on xiaomi site there is a post in which you are instructed to wipe everything and to make factory reset.

Well I'm so glad to have found a real solution here

Since yesterday, no issue at all with the phone, running as usual and all services were up and running

 

[ekrumova]

Hi guys , finally I did it today !
After heating the phone with a hairdryer for about 10 minutes, I was able to enable the USB debugging.
Slight update is that you need to accept the SHA key once it is enabled - meaning unlock the phone and accept it fast.
Then execution of the adb commands were a breeze.
Really appreciate your help guys ! Kudos to XDA