@fergeteg can you send my the link to download the firmware for my HU 8227L and the instructions? fran.roy.morales@gmail.com
I sent an email.
@fergeteg can you send my the link to download the firmware for my HU 8227L and the instructions? fran.roy.morales@gmail.com
Can you send me the last firmware for 9213AJ ?
I have a problem with radio app.
Asimolo76@hotmail.com
Thanks
@fergeteg can you send my the link to download the firmware for my YT9213AJ and the instructions? tablettihui@gmail.com
I have the same problem.
It's posible send a mail with solution.
mateus.j@gmail.com
Tanks in advance
bonsoir,
j'ai flashé mon système YT9213AJ_AHD_00011_V001_20200222 avec ce firmware (ui2 20200417) associé au fichier .bin . après 3 ou 4 sec, un message s'affiche en grand sur mon écran et indique que le fichier update n'est pas valide. Mais surprise, ça fonctionne : balance gauche droite ok, fader avant arrière non et plus de hausse excessive de volume entre le point 17 et 18.
bizarre donc mais ça fonctionne ! merci pour ce post
good evening,
I flashed my system YT9213AJ_AHD_00011_V001_20200222 with this firmware (ui2 20200417) associated with the .bin file. after 3 or 4 seconds, a large message appears on my screen and indicates that the update file is not valid. But surprise, it works: balance left right ok, fader front rear no and no excessive increase in volume between point 17 and 18.
weird so but it works! Thank you for this post
YT9213AJ OTA > 0323
drive.google.com/file/d/1ODTAjpWVm7qk00cxNRLZR_3TrXE421NG
Will work. You do NOT have a dedicated radio chip, so .... Not sure what your expectations of RDS are?
Did you solve your problem with the volume by installing that update? I have the same problem with the volume between levels 17 and 18, a pause and an excessive increase of volume, may you share me the links and which process did you use to install it?
Thanks!
---------- Post added at 09:51 PM ---------- Previous post was at 09:37 PM ----------
I have the volume problem on levels 17 and 18, a pause and a volume increase, do you think the update you shared helps me solve that issue? This is the data of my unit
Android: YT9213AJ_00011_V001_20200321
If it would help me with my unit, could you send me the mail to jero_silentwolf@hotmail.com ?
Thanks in advance!
Even after applied the update ? which is the last version of the YT9213AJ that you have?
my friend can you helpme
Hello,
i have an YT9213A_00009_V001_20191126 Android Radio (Android 9.1, DDR/FLASH: 1G/16G, CPU: A7 1.3GHz x 4)
I have the same Probems with Fading and Balacing settings an like to flash a new Firmware.
I tried to update the firmware with the following steps:
- formated an USB Stick
- copied the XYAUTO_UPDATE(1).BIN and xyauto_ui1_9213A_full_8227L_demo-ota-20200312.ZIP files to the USB Stick
- The Radio recogizes the stick and offers the Update Button
- It starts to update after pressing the update-Button and reboots after 18%
--> after the reboot the Android-Robot is shown by the text update. after 20 seconds the update ends showing the dead Android-Robot and the text "error" is shown.
Please can someone help me by providing the needed Files and an Manual how to update the radio?
Thanks in advance and best regards
maniac2002
maniac200220002@gmail.com
Hi, I've got the same unit, can you please send me the link to this update. my mail address is cyberart@o2.pl, Thank You!!
Hello guys, I wanted to ask for help in choosing the software for my radio. Below are photos of my model, can I ask for support and instructions. I want the radio to have RDS and better sound quality.
My e-mail dawidcieslik@gmail.com
Hi,Hello!
so if you remember what you did in 2021 )
if you would be so kind...
i have a yt9213A. and I am on 6.0 firmware and trying to upgrade to 8.1 a 2GB RAM unit on SPF Flash tool.
I tried Flashing with correct 8.1 firmware in format+download mode (except preloader) but did not get a boot. it was a black screen. wont start.
Should i flash the preloader too? Could your preloader work? (i tried yt9213Aj 6.0 firmware and its compatible.
when flashing all, including the 8.1 preloader (for the yt9213a firmware) it gave brick and i had to do a test point recovery which was nasty.
I dont get the full trick. I think one should flash all the files on the XYauto.com site and should work but it didnt.
Thanks!