Currently no overclocking with this kernel.Hello, sorry to bother BUT...
I havent seen any mention regarding overclocking, is it possible using this kernel?
Thank you, Good work here ofc! Keep it!
After installing this kernel Google Play Market stopped working
---------- Post added at 10:15 PM ---------- Previous post was at 09:50 PM ----------
Phone rebboting after each 5 minutes. How can i uninstall this kernel?
Kernel has nothing to do with Google Play Store.
Maybe some other things with your ROM or apps corrupted.
To restore back kernel, just flash back again your current ROM.
Just want to share great app which manages kernel parameters.
http://goo.gl/3DWAm7
Actually that app is mainly designed for Qualcomm devices, there are not a lot of options for this device
Sent from my D5503 using XDA Free mobile app
No. This kernel only for cm11.
[B]08/02/2015 - BraveKernel Refresh v1.3 for KitKat[/B]
- Added minfree tweak in crontab
- Disabled management of not killable processes
- Tweaked adj and minfree values in init.d
- Added memory tweak in crontab
- Tweaked read_ahead_kb values
- Added F2FS support
- Fixed network arrows and speed information
- Fixed root and storage issues
- Added recovery in FOTA partition support
- Added kexec hardboot support
- Added 3 extra MB of usable RAM
- Added dynamic management of dirty page writebacks
- Added Ultra KSM
- Added entropy tweaks
- Updated BFQ scheduler
- Updated Linaro toolchain
- Improved LZO decompression
- Tweaked LMK
- Improved network speed
- Improved CPU performance
- Improved EXT4 speed
- Improved power management
- Tweaked memory management values
- Enabled clean cache
- Enabled JRCU
[B]21/12/2014 - BraveKernel Refresh v1.0 for KitKat[/B]
- Initial release
cat /sys/boottime/kernel
insmod /system/lib/modules/frandom.ko
chmod 0666 /dev/frandom
chmod 0666 /dev/erandom
mv /dev/random /dev/random.orig
mv /dev/urandom /dev/urandom.orig
ln -s /dev/frandom /dev/random
ln -s /dev/frandom /dev/urandom
echo 5 > /d/cpuidle/deepest_state
cat /d/cpuidle/stats
echo $((200 * 1024 * 1024)) > /sys/block/zram0/disksize
mkswap /dev/block/zram0
swapon /dev/block/zram0
cat /sys/block/zram0/num_reads
cat /sys/block/zram0/num_writes
cat /proc/meminfo | grep swap
su
cd /cache
dd if=/dev/zero of=swapfile bs=1024 count=81920
mkswap swapfile
swapon swapfile
echo on > /sys/kernel/abb-fg/fg_cyc
echo off > /sys/kernel/abb-fg/fg_cyc
echo dischar=75 > /sys/kernel/abb-fg/fg_cyc
echo dischar=70 > /sys/kernel/abb-fg/fg_cyc
cat /sys/kernel/abb-chargalg/eoc_status
echo 100 > /sys/kernel/abb-ponkey/emulator
echo 800 > /sys/kernel/abb-ponkey/emulator
echo on > /sys/kernel/abb-codec/anagain3
echo off > /sys/kernel/abb-codec/anagain3
echo left=?? > /sys/kernel/abb-codec/anagain3
echo right=?? > /sys/kernel/abb-codec/anagain3
echo gain=?? > /sys/kernel/abb-codec/anagain3
echo on > /sys/kernel/abb-codec/hsldiggain
echo off > /sys/kernel/abb-codec/hsldiggain
echo gain=?? > /sys/kernel/abb-codec/hsldiggain
echo on > /sys/kernel/abb-codec/hsrdiggain
echo off > /sys/kernel/abb-codec/hsrdiggain
echo gain=?? > /sys/kernel/abb-codec/hsrdiggain
echo on > /sys/kernel/abb-codec/hslowpow
echo off > /sys/kernel/abb-codec/hslowpow
echo mode=? > /sys/kernel/abb-codec/hslowpow
echo on > /sys/kernel/abb-codec/hsdaclowpow
echo off > /sys/kernel/abb-codec/hsdaclowpow
echo mode=? > /sys/kernel/abb-codec/hsdaclowpow
echo on > /sys/kernel/abb-codec/hshpen
echo off > /sys/kernel/abb-codec/hshpen
echo mode=? > /sys/kernel/abb-codec/hshepen
echo on > /sys/kernel/abb-codec/classdhpg
echo off > /sys/kernel/abb-codec/classdhgp
echo gain=?? > /sys/kernel/abb-codec/classdhpg
echo on > /sys/kernel/abb-codec/classdwg
echo off > /sys/kernel/abb-codec/classdwp
echo gain=?? > /sys/kernel/abb-codec/classdwg
echo on > /sys/kernel/abb-codec/addiggain2
echo off > /sys/kernel/abb-codec/addiggain2
echo gain=?? > /sys/kernel/abb-codec/addiggain2
echo on > /sys/kernel/abb-codec/eardiggain
echo off > /sys/kernel/abb-codec/eardiggain
echo gain=?? > /sys/kernel/abb-codec/classdwg
This is a misc tweak
View shortcir this file first
[7] EnShortPWD
0: Automatic switch off on short circuit detection is disabled
1: Automatic switch off on short circuit detection is enabled
[6] EarShortDis
0: Short circuit detection on Ear driver enabled
1: Short circuit detection on Ear driver disabled
[5] HsShortDis
0: Short circuit detection on HsL and HsR drivers enabled
1: Short circuit detection on HsL and HsR drivers disabled
[4] HsPullDEn
0: HsL and HsR outputs are in high impedance
1: HsL and HsR outputs are pulled down to ground
[2] HsOscEn (ABBamp enables it by default)
0: The HS drivers use the system clock
1: The HS drivers use a local oscillator (system clock absent: analog path only)
[1] HsFadDis
0: All intermediate steps are applied between two programmed gains (fading)
1: Gain on HS is applied immediately
[0] HsZcdDis
0: HS gain changes on signal zero cross (unless time-out occurs)
1: HS gain is changed without zero cross control
[CODE]echo ?? ?? > /sys/kernel/abb-codec/shortcir
echo [Index] [Disable?] > anaconf4
echo 5 1 > anaconf4
echo 5 0 > anaconf4
echo 0 > chargepump to use fixed 1.8V supply.
echo 1 > chargepump to use dynamic voltage supply, lower power cost.
echo on > lpa_mode to enable LPA mode
echo vape=0x?? > lpa_mode to adjust Vape voltage used in LPA mode
echo REG VAL > codec_reg
echo 0x16 0x00 > codec_reg
echo 0x4F 0x00 > codec_reg
echo 0x50 0x00 > codec_reg
echo 0x04 0x00 > codec_reg
echo 1/0 > /sys/devices/platform/nmk-i2c.2/i2c-2/2-0053/torch_enable
echo 149600 > /sys/devices/platform/nmk-i2c.2/i2c-2/2-0053/torch_current
cat /sys/kernel/fsync/mode
echo 1 > /sys/kernel/fsync/mode
echo 2 > /sys/kernel/fsync/mode
echo 0 > /sys/module/mali/parameters/mali_debug_level
echo xx > /sys/module/mali/parameters/mali_l2_max_read
echo xx > /sys/module/mali/parameters/mali_pm_sampling_rate
echo 1 > /sys/module/mali/parameters/mali_pp_scheduler_balance_jobs
echo xxx > /sys/module/mali/parameters/mali_utilization_sampling_rate
echo 5 > /sys/module/mali/parameters/mali_debug_level
cat /proc/kmsg | grep -i utilization
echo 120 > mali_utilization_low_to_high
echo 50331648 > /sys/module/mali/parameters/pre_allocated_memory_size_max
echo 6 > /sys/module/mali/parameters/mali_oskmem_allocorder
busybox sysctl net.ipv4.tcp_available_congestion_control
busybox sysctl -w net.ipv4.tcp_congestion_control=YOU_WANT_TO
echo 1 > /sys/kernel/abb-fg/fg_refresh
[B]08/02/2015 - BraveKernel Refresh v1.3 for KitKat[/B]
- Added minfree tweak in crontab
- Disabled management of not killable processes
- Tweaked adj and minfree values in init.d
- Added memory tweak in crontab
- Tweaked read_ahead_kb values
- Added F2FS support
- Fixed network arrows and speed information
- Fixed root and storage issues
- Added recovery in FOTA partition support
- Added kexec hardboot support
- Added 3 extra MB of usable RAM
- Added dynamic management of dirty page writebacks
- Added Ultra KSM
- Added entropy tweaks
- Updated BFQ scheduler
- Updated Linaro toolchain
- Improved LZO decompression
- Tweaked LMK
- Improved network speed
- Improved CPU performance
- Improved EXT4 speed
- Improved power management
- Tweaked memory management values
- Enabled clean cache
- Enabled JRCU